lock SUBARU LEGACY 2001 3.G User Guide

2-8
HB1000BB
1. Press once to Unlock
driver’s door.
2. Press a second time to Unlockall doors.
Press to Lock all doors. Press and Hold to activate panic alarm.
LED
Locking the doors
Briefly p ress the “LOCK/ARM ” b utton (for less than two sec ond s) to
loc k all d oors (and rear g ate on the station wag on) . The horn will
sound one time.
If any of the d oors (or the rear g ate) is not fully c losed , the horn will
sound three times to alert you that the d oors (or t he rear g ate) are not
p rop erly c losed . When you c lose the d oor, it will a utomatic ally loc k.
Unlocking the doors
Briefly p ress the “UNLOCK/DISARM ” b utton (for less than two
sec ond s) to unloc k the d river ’s d oor. The horn will sound two times. To
unloc k all d oors (and rear g ate on the station wag o n), b riefly p ress the
“ UNLOCK/DISARM ” b utton a sec ond time.
Illuminated entry
The interior (d ome) lig ht will illuminate when the “UNLOCK/DISARM ”
b utton is p ressed . The lig ht will illuminate for ap p roximately 30
sec ond s or until the key is inserted in the ig nitio n switc h or until the
“ LOCK/ARM ” b utton is p ressed . Onc e any of the d oors (or the r ear
g ate on the station wag on) is op ened , this func tion will b e c anc eled .
The interior lig ht must b e set to the middle position in ord er for this
func tion to op erate. Sounding a panic alarm
To ac tivate the alarm, keep the “LOCK/ARM ” b utton p ressed for more
than two seconds .
To d eac tivate it, p ress the “LOCK/ARM ” b utton or “UNLOCK/DISARM ”

Keys and doors2-9
–
CONTINUED –
b utton. Unless a b utton on the remote is p ressed , t
he alarm will b e
d eac tivated after ap p roximately 30 sec ond s. Selecting audible signal operation
Using the horn, the system will g ive you an aud ib le sig nal when the
d oors loc k and unloc k. If d esired , you may turn the aud ib le sig nal off.
To turn the aud ib le sig nal off, simultaneously d ep r ess “LOCK/ARM ”
and “UNLOCK/DISARM ” b uttons for more than two sec ond s. The horn
will sound two times to inform you that the aud ib le sig nal has b een
turned off.
To turn the aud ib le sig nal on, simultaneously d ep re ss “LOCK/ARM ”
and “UNLOCK/DISARM ” b uttons for more than two sec ond s. The horn
will sound one time to inform you that the aud ib le sig nal has b een
turned on. Replacing the battery
CAUTION
Do not let dust, oil or water get on or in the transmitter when
replacing the battery.
When the transmitter b attery b eg ins to g et weak, tr ansmitter rang e will
b eg in to d ec rease and the LED will not illuminate. Rep lac e the b attery
as soon as p ossib le.
HB1002BB
HB1001BA
Positive (+) side facing up
To rep lac e the b attery:
1. Remove the two sc rews on the b ac k of the transmit ter c ase b y

2-10using a p hillip s sc rewd river.
2. Sep arate the c ase.
3. Remove the old b attery from the hold er.
4. Rep lac e with a new b attery (Typ e CR2032 or eq uiva
lent) making
sure to install the new b attery with the p ositive ( + ) sid e fac ing up .
5. Install the b ac k half of the transmitter c ase.
6. Reinstall the two sc rews on the b ac k of the trans mitter c ase.
After the battery is replaced, the transmitter must be synchro-nized with the keyless entry system ’s control unit. Press either
the “LOCK/ARM” or “UNLOCK/DISARM” button six times to syn-
chronize the unit. Replacing lost transmitters
If you lose a transmitter or want to p urc hase ad d it ional transmitters
(up to four c an b e p rog rammed ), you should re-p rog r am all of your
transmitters for sec urity reasons. It is rec ommend e d that you have
your d ealer p rog ram all of your transmitters into y our system.
n Programming the transmitters
The keyless entry system is eq uip p ed with a sp ec ial c od e learning
feature that allows you to p rog ram new transmitter c od es into the sys-
tem or to d elete old ones. The system c an learn up to four uniq ue
transmitter c od es. The four transmitter c od es may b e the same or d if-
ferent.
To enter the programming mode:
HB1005BC
HB1000CB
1 Press to dis-
arm the security system (if so equipped).
2
3

Keys and doors2-11
–
CONTINUED –
1. Disarm the sec urity system. (if your vehic le is e
q uip p ed with the
op tional sec urity system.)
2. Op en the d river ’s d oor and sit in the d river ’s seat.
3. Close the d river ’s d oor.
HB2032BB
4. Plac e the ig nition key into the ig nition switc h a nd c yc le the switc h
from LOCK to ON ten times within 15 seconds. Be sure to stop at the
LOCK p osition and leave the key in the ignition . The horn will sound
onc e to ind ic ate that you are in the transmitter p r og ramming mod e.
NOTE
You must finish the next step (opening the driver ’s door) within
45 seconds of starting this procedures.
To program the transmitters:
HB1000DB
1
2
HB1005BB3 Press any button.

2-14
Arming the system
n To arm the system using remote transmitter
HB2033BB
Press to Arm the system. Press to Disarm the system.
HB1000EB
1. Close all wind ows and moonroofs (if so eq uip p ed ).
2. Remove the key from the ig nition switc h.
3. Op en the d oors and g et out of the vehic le.
4. Make sure that the eng ine hood (and the trunk lid ) are loc ked .
5. Close all d oors (and the rear g ate on the station wag on).
6. Briefly p ress the “LOCK/ARM ” b utton (for less than two sec ond s).
All d oors (and the rear g ate on the station wag on) will loc k, the horn
will sound one time, the p arking lig hts will flash one time and the ind i-
c ator lig ht starts flashing slowly (ap p roximately o nc e every two
sec ond s).
If any of the d oors, (rear g ate or trunk lid ) is no t fully c losed , the horn
sound s three times, the p arking lig hts flash three times and the ind i-
c ator lig ht flashes rap id ly to alert you that the d oors (or the rear g ate)
are not p rop erly c losed . When you c lose the d oor, t he system will au-
tomatic ally arm and d oors will automatic ally loc k.

Keys and doors2-15
–
CONTINUED –
n
To arm the system using power door locking switches
HB2024CC
1. Close all wind ows and moonroofs (if so eq uip p ed ).
2. Remove the key from the ig nition switc h.
3. Op en the d oors and g et out of the vehic le.
4. Make sure that the eng ine hood (and the trunk lid ) are loc ked .
5. Close the d oors (and the rear g ate on the station wag on) b ut leave
only the d river ’s d oor or the front p asseng er ’s d oor op en.
6. Push the p ower d oor loc king switc h forward ( “LOCK ” sid e) to set
the d oor loc ks.
7. Close the d oor. The horn will sound one time, the p arking lig hts will
flash one time and the ind ic ator lig ht will start f lashing slowly (ap p roxi-
mately onc e every two sec ond s) to inform you that t he system has
armed . NOTE The system can be armed even if the engine hood, the windows and/or moonroofs are opened. Always make sure that they arefully closed before arming the system. Disarming the system
Briefly p ress the “UNLOCK/DISARM ” b utton (for less than two
sec ond s) on the remote transmitter. The d river ’s d oor will unloc k, the
horn will sound two times, the p arking lig hts will flash two times and
the ind ic ator lig ht will g o off.

2-16To unloc k all d oors (and the rear g ate on the stati
on wag on), b riefly
p ress the “UNLOCK/DISARM ” b utton a sec ond time.
n Emergency disarming
If you c annot d isarm the system using the transmitt er (i.e. the trans-
mitter is lost, b roken or the transmitter b attery i s too weak), you c an
d isarm the system without using the transmitter.
To d isarm the system:
1. Unloc k the d oor with the key and then op en the d o or.
2. The alarm will sound .
3. Insert the key into the ig nition switc h and c yc le it from the “LOCK ”
to the “ON ” p osition three (3) times within 5 seconds.
Sounding a panic alarm
To ac tivate the alarm, keep the “LOCK/ARM ” b utton p ressed for more
than two seconds .
To d eac tivate it, p ress the “LOCK/ARM ” b utton or “UNLOCK/DISARM ”
b utton.
The p arking lig hts will also flash when the alarm i s ac tivated .
Unless a b utton on the remote is p ressed , the alarm will b e d eac ti-
vated after ap p roximately 30 sec ond s. Valet mode
When you c hoose the valet mod e, the sec urity system d oes not op er-
ate. In valet mod e, the remote transmitter is used only for loc king and
unloc king the d oors (and rear g ate on the station w ag on) and p anic
ac tivation.
To enter the valet mod e, op en the d river ’s d oor and keep the
“ UNLOCK/DISARM ” b utton d ep ressed for more than two seconds .
The ind ic ator lig ht rep eated ly flashes two times wh ile the system is in
valet mod e.
To exit valet mod e, op en the d river ’s d oor and keep the “UNLOCK/
DISARM ” b utton p ressed for more than two seconds. The ind ic ator
will stop flashing .

Keys and doors2-17
–
CONTINUED –

Passive arming
When p assive arming mod e has b een p rog rammed b y the d ealer,
arming of the system is automatic ally ac c omp lished without using the
remote transmitter. Note that in this mod e, DOORS M UST BE MANU-
ALLY LOCKED. n To enter the passive mode
WARNING
Do not disconnect or tamper with any yellow connector and/or any harness covered with yellow insulation and/or tape.Doing so could result in accidental inflation of the SRS airbag orcould make the SRS airbag system inoperative, which may result
in serious injury.
HB2038BB
HB2036BA
1. Remove the sid e sill c over on the d river ’s sid e.
1) Op en the d river ’s d oor.
2) Remove the c lip b y p rying the ed g e with sc rewd riv er.
3) Remove the sid e sill c over b y p ulling it up .
2. Connec t the white (1 p ole) c onnec tor.
3. Turn the ig nition switc h from the “LOCK ” to the “ON ” p osition.
4. Install the sid e sill c over.
To p lac e the system in ac tive arming mod e (remote r eq uired for ac -
tivation), d isc onnec t the white c onnec tor.

2-18n
Arming the system CAUTION
In passive mode, the system will automatically activate the alarm
but WILL NOT automatically lock the doors. In order to lock thedoors you must either lock them as indicated in step 4 below orwith the key once they have been closed. Failure to lock thedoors manually will result in a higher security risk.
HB2024DB
HB2031BB
1. Turn the ig nition switc h to the “ON ” p osition.
2. Turn the ig nition switc h from “ON ” to “LOCK ” p osition and remove
the key from the ig nition switc h.
3. Op en the d oors and g et out of the vehic le.
4. Before c losing the d oors, loc k all d oors with the insid e d oor loc k
levers.
5. Close the d oors. The system will automatic ally ar m after one min-
ute.
In the p assive mod e, the system c an also b e armed w ith the remote
transmitter or with the p ower d oor loc king switc hes . If the remote
transmitter or p ower d oor loc k switc h is used to lo c k the vehic le, arm-
ing will take p lac e immed iately reg ard less of wheth er or not the p as-
sive mod e has b een selec ted .

Keys and doors2-19
–
CONTINUED –

Disarming the system
To d isarm the system, b riefly p ress the “UNLOCK/DISARM ” b utton on
the transmitter. Tripped sensor identification
If the horn sound s four times and the p arking lig ht s flash four times
when you d isarm the system, this ind ic ates that the alarm was trig -
g ered . The numb er of times the ind ic ator lig ht flas hes ind ic ates what
sensor c aused the alarm c ond ition.
To enter id entific ation mod e:
1. Op en the d river ’s d oor and leave it op en.
2. Turn the ig nition switc h to the “ON ” p osition two times. ( “LOCK ” 
“ ON ”  “ LOCK ”  “ ON ”  “ LOCK ”)
3. The ind ic ator lig ht will start flashing .
The ind ic ator lig ht p rovid es the following ind ic ati ons.
Flashing one time: Any d oor, the rear g ate or the trunk lid has b een
op ened .
Flashing three times: The imp ac t sensor in the system ’s unit has
b een ac tivated . This may ind ic ate that your vehic le has b een shoc ked
or tamp ered with b y some outsid e forc e and /or unaut horized p erson.
Flashing four times: The ig nition switc h has b een turned on.
To exit this mod e, c lose the d oor and turn the ig ni tion switc h to the
“ ON ” p osition.