Engine oul SUZUKI BALENO 1999 1.G Owners Manual

WARRANTY POLICY
60G-74E

dealer/service station,

(k) any vehicle which has been used for purposes other than

what it was designed for.

(I) any damage or deterioration caused by industrial pollution

and bird droppings,

(m) insignificant defects which do not affect the function of the

vehicle including without limitation sound, vibration and fluid

seep,

(n) any natural wear and tear including without limitation, ageing

etc.

For Maruti Air-Conditioned Vehicles

(o) V-belts, hoses and gas leaks.

(5) Extent of Warranty:

This warranty is the entire written warranty given by Maruti for

Maruti vehicles and no dealer or its or his agent or employee

is authorised to extend or enlarge this warranty and no dealer

or its or his agent or employee is autorised to make any oral

warranty on Maruti's behalf.

Maruti reserves the right to add any improvements or change

the design of any model at any time with no obligation to make

the same changes on units previously sold.

(6) Warranty Service:

To obtain warranty service, the complete vehicle must be

presented at the owner's expenses to any authorised Maruti

dealer.

(7) Owner's Warranty Responsibilities:
It is responsibility of each owner to:

(a) make certain that the warranty registration/PDI card was

completed at the time of delivery of the vehicle;

(b) have performed, at his own expenses, by an Maruti

authorised dealer/service station all the service inspections

specified in the Maruti "Owner's Manual and Service Booklet"

and maintain adequate proof that such service inspections

have been performed.

(c) make certain that the Maruti authorised dealer/service station

performing the service inspection has certified the work on

the "Maintenance Service Record" page in the "Owner's

Manual and Service Booklet" and

(d) present the Maruti "Owner's Manual and Service Booklet" to

the authorised Maruti dealer whenever requesting service

inspections or warranty service.

If the "Owner's Manual and Service Booklet" should be lost or

destroyed the owner should consult the authorised Maruti dealer from

whom the vehicle was purchased for instructions concerning

replacement of the "Owner's Manual and Service Booklet".

(8) Disclaimer of Consequential Damage:

Maruti assumes no responsibility for loss of vehicle, loss of time,

inconvenience or any other indirect incidental or consequential

damage resulting from the vehicle not being available to the

owner because of any defect covered by this warranty.

(9) Change of owner

Even if ownership of the vehicle changes, the remaining

warranty period is effective for the new owner.

2-2

60G-74E

EMISSION WARRANTY

Maruti offers the Emission Warranty on all Maruti vehicles (aparts from the Regular warranty and will run parallel to the regular

product warranty) only in four metropolitan cities (New Delhi, Kolkata, Mumbai and Chennai) with effect from July 1st, 2001.

Terms:

The Emission Warranty will be applicable for 80,000 kms or 3 years (Whichever comes earlier) from the date of delivery to the

first owner. The remaining warranty terms will be valid in case of any change in ownership provided the production of all valid documents.

Conditions :

1. Under Emission Warranty, Warranty claims will be admitted for a prima facie examination, in case vehicle fails to meet to the

Emission Standard as specified In sub rule (2) of rule no. 115 of Central Motor Vehicles Rules (CMVR), 1989.

2. The warranty claims will only be accepted after examination carried out by Maruti or it's dealer which leads to firm conclusions

that the

a) Original settings have not been tempered in any case.

b) Part (as given in Annexure-A) has a manufacturing defect.

c) Vehicle is unable to meet the Emission Standards (as given in 1.), inspite of the vehicle having been maintained and used

in accordance with the instructions as specified in Owner's Manual and Service Booklet and the used fuel and different oils

(Engine oil, Transmission oil, Brake oil etc.) are also as per specification.

3. The method of examination for deciding the warranty of the parts will be at the sole discretion of Maruti and it's dealer and

results of the examination will be final and binding. If after examination, the warrantable condition is not established, Maruti

and it's dealer has the right to charge all, or part of the cost of such examination.

4. Under Emission Warranty, the parts (as given in Annexure-A) will be changed free of cost, but the consumables will be charged

as per actual.

5. If the part covered under Emission Warranty or the associated parts, are not independently replaceable, on account of these

being integral parts of a complete assembly, Maruti and it's dealer will have the sole discretion to replace either the entire assembly

or by using some of the parts of the system through suitable repairs or modifications.
8

9

60G-74E
BEFORE DRIVING

WINDOWS

60G-03-009E

Electric window controls (if equipped)

The driver's door has switches ®,®,© & ©

to operate the driver's window, front

passenger's window, rear right and rear left

passenger's window respectively.

The passenger's door only has a switch ©

to operate the passenger's window. The

electric windows can only be operated when

the ignition switch is in the "ON" position.

To open a window with the driver's door

switches, push the top part of the switch and

to close the window lift up the top part

of the switch.
6OG-O3-010E

The driver's window has an "auto-down"

feature for added convenience (at toll booths

or drive-through restaurants, for example).

This means you can open the window without

holding the window switch in the "Down"

position. Press the driver's window

switch completely down and release it. To

stop the window before it reaches the

bottom, lift up the switch briefly.
To open or to close a window with the

passenger's door switch, push down or push

up the switch.

19

3-6

BEFORE DRIVING

60G-74E

60G-03-011E

The driver's door also has a lock switch for

the passenger's window. When you push in

the lock side of the switch, the passenger's

windows can not be raised or lowered by

operating either of the switches ®,@,® & ©.

To restore normal operation, push the unlock

side of the switch.
60G-03-012

You should always push the lock side

of the lock switch when there are

children in the vehicle. Children can be

seriously injured if they get part of their

body caught by the window during

operation.
NOTE:

The rear side door windows are not designed

to open fully. They can be opened about 2/3

of the way down.

3-7
20
CAUTION

Since the electric windows consumes

a large amount of electricity, the same

should not be used excessively with

engine in "OFF" condition.

6OG-74E
STEERING COLUMN CONTROLS

ACC

Accessories such as the radio can operate,

but the engine is off.

ON

This is the normal operating position. All

electrical systems are on.

START

This is the position for starting the engine using

the starter motor. The key should be released

from this position as soon as the engine starts.

Never remove the ignition key while

the vehicle is moving. The steering

wheel will lock and you will not be

able to steer the vehicle.

Do not leave children alone In a

parked vehicle. Unattended children

could cause accidental movement of

the vehicle, which could result in

severe personal Injury.

Always remove the key when parked

to prevent unintentional operation of

the vehicle and to improve security.
LIGHTING/TURN SIGNAL

CONTROL LEVER

CAUTION

Do not use the starter motor for

more than 15 seconds at a time. If

the engine does not start; wait 15

seconds before trying again. If the

engine does not start after several

attempts, check the fuel and ignition

systems or consult your MARUTI

dealer.

Do not leave the ignition switch in

the "ON" position if the engine is not

running as the battery will

discharge.
60G-04-003

This control lever is located on the outboard

side of the steering column. Operate the lever

as described below.

Lighting Operation

To turn the lights on or off, twist the knob on

the end of the lever. There are three positions:

in the "OFF" position all lights are off; in the

middle position the front parking lights, tail-

lights, registration plate light, and instrument

lights are on, but the headlights are off; in the

third position the headlights come on in

addition to the other lights.

33

4-2

STEERING COLUMN CONTROLS
60G-74E

With the headlights on, push the lever forward

to switch to the high beams (main beams) or

pull the lever toward you to switch to the low

beams. When the high beams (main beams)

are on, a light on the instrument panel will

come on. To flash the high beams (main

beams) pull the lever slightly towards you and

release it.

Lights "On" Reminder (if Equipped)

A buzzer/chime sounds to remind you to turn

off the lights if they are left on when the ignition

key is removed and the driver's door is opened.
Turn Signal Operation

With the ignition switch in the "ON" position,

move the lever up or down to activate the left

or right turn signals.

Normal Turn Signal

Move the lever clockwise until it clicks to signal

a right turn or anticlockwise to signal a left

turn. When the turn is completed, the signal

will cancel and the lever will return to its normal

position.
6OG-04-006

Lane Change Signal

Some times, such as when changing lanes,

the steering wheel is not turned far enough

to cancel the turn signal. For convenience,

you can flash the turn signal by moving the

lever part way and holding it there. The

lever will return to its normal position when

you release it.

4-3
34
60G-04-006

60G-04-005

60G-04-004E

60G-74E
INSTRUMENT PANEL

INSTRUMENT CLUSTER

© Speedometer

® Odometer

© Trip meter (if equipped)

© Trip meter reset knob

© Tachometer (if equipped)

© Fuel gauge

® Temperature gauge

© Warning and indicator lights

60G-05-002

39

5-2

INSTRUMENT PANEL
60G-74E

WARNING AND INDICATOR LIGHTS

70F-07-070

Brake fluid level warning/Parking Brake

Indicator light

This light operates under three conditions:

1) when the ignition switch is turned to the

"START' position, 2) when the fluid in the brake

fluid reservoir falls below the specified level

or 3) when the parking brake is not fully

released and the ignition switch is in the "ON"

position. The light should go out after starting

the engine and fully releasing the parking

brake, if the fluid in the brake fluid reservoir is

adequate. If the light does not go off or comes

on whilst you are driving, it may mean that

there is something wrong with the vehicle's

braking system. If this happens, you should:

1) Pull off the road and stop carefully.

Remember that stopping distance may

be longer, you may have to push

harder on the pedal, and the pedal

may go down farther than normal.
2) Test the brakes by carefully starting and

stopping at the side of the road.

3) If you determine that it is safe, drive

carefully at low speed to the nearest dealer

for repairs.

Have the vehicle towed to the nearest

dealer for repairs.
or

4)

If any of the following conditions occur,

you should Immediately ask your

MARUTI dealer to inspect the brake

system.

• If the brake fluid level warning light

does not go out after the engine has

been started and the parking brake

has been fully released.

• If the brake fluid level warning light

does not come on when the ignition

switch is turned to the "START"

position.

• If the brake fluid level warning light

comes on at any time during vehicle

operation.

NOTE:

Because the disc brake system is self

adjusting, the fluid level will drop as the brake

pads become worn.

Replenishing the brake fluid reservoir is

considered normal periodic maintenance.
70F-03-039

Oil Pressure Light

This light comes on when the ignition switch

is turned on, and goes out when the engine

is started. The light will come on and remain

on if there is insufficient oil pressure. If the

light comes on when driving, pull off the

road as soon as you can and stop the

engine. Check the oil level and add oil if

necessary (see pages 9-8 and 9-9). If there

is enough oil, the lubrication system should

be inspected by your MARUTI dealer before

you drive the vehicle again.

5-3
40

60G-74E
INSTRUMENT PANEL

60G-09-002

CAUTION

If you operate the engine with this

light on, severe engine damage can

result.

Do not rely on the Oil Pressure Light

to indicate the need to add oil. Be

sure to periodically check the engine

oil level (see pages 9-8 and 9-9).
70F-03-009

Charging Light

This light comes on when the ignition switch

is turned on, and goes out when the engine is

started. The light will come on and remain on

if there is something wrong with the battery

charging system. If the light comes on when

the engine is running, the charging system

should be inspected immediately by your

MARUTI dealer.

CAUTION

Do not continue driving long with the

charging light ON as this will drain the

battery 'dead'.
72F-05-027

"Malfunction Indicator" Light

Your vehicle has a computer-controlled

emission control system. A "Malfunction

Indicator" light is provided on the instrument

panel to indicate when it is necessary to have

the emission control system serviced. The

"Malfunction Indicator" light comes on when

the ignition switch is turned to "ON" and goes

out when the engine is started.

If the "Malfunction Indicator" light comes on

when the engine is running, there is a problem

with the emission control system. Take the

vehicle to your MARUTI dealer to have the

problem corrected.

CAUTION

Continuing to drive the vehicle when

the "Malfunction Indicator" light is on

can cause permanent damage to the

vehicle's emission control system, and

can affect fuel economy and

driveability.

5-4

INSTRUMENT PANEL
60G-74E

70F-03-042

Turn Signal Indicators

When you turn on the left or right turn signals,

the corresponding green arrow on the

instrument panel will flash along with the

respective turn signal lights. When you turn

on the hazard warning switch, both arrows will

flash along with all of the turn signal lights.

70F-03-043

Main Beam (High Beam) Indicator Light

This indicator comes on when headlight main

beams (high beams) are turned on.
SPEEDOMETER/ODOMETER/

TRIPMETER (if equipped)

60G-05-003

© Speedometer

© Odometer

(D Trip meter

© Trip meter reset knob

The speedometer indicates vehicle speed in

km/h.The odometer records the total distance

the vehicle has been driven. The tripmeter can

be used to measure the distance travelled on

short trips or between fuel stops. You can reset

the tripmeter to zero by pushing the reset

knob.
CAUTION

Keep track of your odometer reading

and check the maintenance schedule

regularly for required services.

Increased wear or damage to certain

parts can result from failure to perform

required services at the proper mileage

intervals and your warranty rights may

be affected.

5-5

42
41

60G-74E
INSTRUMENT PANEL

TACHOMETER (if equipped)

FUEL GAUGE
TEMPERATURE GAUGE

60G-05-004

The tachometer indicates engine speed in

revolutions per minute.

Never drive with the engine speed

indicator in the red zone or severe

engine damage can result.
60G-05-005

This gauge gives an approximate indication

of the amount of fuel in the fuel tank as shown

in figure. "P stands for full and "E" stands for

empty.

If the indicator gets in the red zone, refill the

tank as soon as possible.

Note:

This vehicle has fuel gauge of new design.

Even when the ignition switch is "OFF", the

needle will not return to "E" position but will

show the reading.
60G-05-006

When the ignition switch is on, this gauge

indicates the engine coolant temperature.

Under normal driving conditions, the indicator

should stay within the normal, acceptable

temperature range between "H" and "C". If the

indicator approaches "H", and maintains that

reading, overheating is indicated. Follow the

instructions for engine overheating in the

EMERGENCY REMEDIES section.

CAUTION

Continuing to drive the vehicle when

engine overheating is indicated, can

result in severe engine damage.

43

5-6

INSTRUMENT PANEL

60G-74E

HAZARD WARNING SWITCH
REAR WINDOW DEFROSTER SWITCH CIGARETTE LIGHTER (if equipped)

(if equipped)

60G-05-007

Push in the hazard warning switch to activate

the hazard warning lights. All four turn signal

lights and both turn signal indicators will flash

simultaneously. To turn off the lights, push the

switch again.

Use the hazard warning lights to warn other

traffic during emergency parking or when your

vehicle could otherwise become a traffic

hazard.
60G-05-008

When the rear window is misted, push this

switch to clear the window. An indicator light

will be lit when the defroster is on. The

defroster will only work when the ignition

switch is in the "ON position. To turn off the

defroster, push the switch again.

CAUTION

The rear window defroster uses a large

amount of electricity. Be sure to turn

off after the window has become clear.
60G-05-009

To use the cigarette lighter, push it all the way

into the receptacle and release it. It will

automatically heat up and will pop out to its

normal position when it is ready for use.

5-7
44

60G-74E
INSTRUMENT PANEL

60G-05-018

Cool Face/Warm Feet

Push the "BI-LEVEL" button and move the air

intake lever to "FRESH AIR", the temperature

control lever to the desired temperature

position, and the fan switch to the desired fan

speed position. Unless the temperature control

lever is in the fully "COOL" position or fully

"HOT position, the air that comes out of the

center and side outlets will be cooler than the

air that comes out of the floor outlets.
60G-05-019

Defrosting/Warm Feet

Push the "HEAT & DEFROST' button and

move the air intake lever to "FRESH AIR", the

temperature control lever to the desired

temperature position, and the fan switch to

"HIGH". When the windscreen has become

clear, move the fan switch to the desired fan

speed position.
60G-05-020

Defrosting

Push the "DEFROST' button and move the

air intake lever to "FRESH AIR", the

temperature control lever to the desired

temperature position, and the fan switch to

"HIGH" Moving the temperature control lever

to a higher temperature position increases

defrosting efficiency. When the windscreen

has become clear, move the fan switch to the

desired fan speed position.

49

5-12

INSTRUMENT PANEL

60G-74E

AIR CONDITIONING SYSTEM

(if equipped)
SYSTEM OPERATING INSTRUCTIONS

60G-05-021

The air conditioning system can be used to

provide cooling and dehumidifying, as

described below. To turn on the air conditioning

system, push in the A/C button and move the

fan switch to a position other than "OFF". An

indicator light will come on when the air

conditioning system is on. To turn off the air

conditioning system, push the A/C button again.

During operation of the air conditioner, you may

notice slight changes in engine speed. These

changes are normal, the system is designed

so that the compressor turns on or off to

maintain the desired temperature. Less

operation of the compressor results in better

fuel economy.
60G-05-022

Normal Cooling (using outside air)

Push in the A/C button and the

"VENTILATION" button, and the move the air

intake lever to "FRESH AIR", the temperature

control lever to the "COOL" position, and the

fan switch to the desired fan speed position.

Moving the fan switch to a higher fan speed

position increases cooling efficiency.

If the ambient temperature is high enough to

cause insufficient cooling, use the "Quick

Cooling" as following.
60G -05-023

Quick Cooling (Using recirculated air)

The lever settings are the same as for normal

cooling except you move the air intake lever

to "RECIRCULATED AIR". If you use this

cooling method for a extended period of time,

the air in the vehicle can become

contaminated. Therefore, you should

occasionally move the air intake lever to

"FRESH AIR".

NOTE:

If your vehicle has been left in the sun with

the windows closed, it will cool faster if you

open the windows briefly while you operate

the air conditioner with the air intake lever at

"FRESH AIR" and the fan at high speed.

5-13
50

OTHER CONTROLS AND EQUIPMENTS
60G-74E

PARKING BRAKE LEVER

63B-06-001E

The parking brake lever is located between

the seats. To apply the parking brake, hold the

brake pedal down and pull the parking brake

lever all the way up.
63B-06-002E

To release the parking brake, hold the brake

pedal down, pull up slightly on the parking

brake lever, push the button on the end of the

lever with your thumb, and lower the lever to

its original position.
Never drive your vehicle with the

parking brake on: rear brake

effectiveness can be reduced from

over heating, brake life may be

shortened, or permanent brake

damage may result.

If the parking brake does not hold

the vehicle securely or does not fully

release, have your vehicle inspected

immediately by an authorized

MARUTI dealer.

Always apply the parking brake fully

before leaving your vehicle or it may

move, causing injury or damage. When

parking, make sure the gear shift lever

is left in first gear or reverse.

Remember, even though the

transmission is in gear, you must

always apply the parking brake fully.

6-1
54

60G-74E
OTHER CONTROLS AND EQUIPMENT

PEDALS

GEAR LEVER

60G-06-001

Clutch Pedal ©

The clutch pedal is used to disengage the drive

to the wheels when starting the engine,

stopping, or shifting the transmission lever.

Depressing the pedal disengages the clutch.

CAUTION

Do not drive with your foot resting on

the clutch pedal. It could result in

excessive clutch wear, clutch damage,

or unexpected loss of engine braking.
Brake Pedal ®

Your MARUTI vehicle is equipped with front

disc brakes and rear drum brakes. Depressing

the brake pedal applies both sets of brakes.

You may hear occasional brake squeal when

you apply the brakes. This is a normal

condition caused by environmental factors

such as cold, wet, snow, etc.

If brake squeal is excessive and occurs

each time the brakes are applied, you

should have the brakes checked by

your MARUTI dealer.

A WARNING

Do not "ride" the brakes by applying

them continuously or resting your foot

on the pedal. This will result in

overheating of the brakes which could

cause unpredictable braking action,

longer stopping distances, or

permanent brake damage.

Accelerator Pedal ®

This pedal controls the speed of the engine.

Depressing the accelerator pedal increases

power output and speed.
70F-04-005E

The gear change pattern is shown in the

illustration. For details on how to use the

transmission, refer to USING THE

TRANSMISSION in the OPERATING YOUR

VEHICLE section.

55

6-2

S0G-74E
OPERATING YOUR VEHICLE

OPERATING YOUR VEHICLE

Exhaust Gas Warning 7-1

Daily Inspection Checklist 7-1

Starting the Engine 7-2

Using the Transmission 7-3

Braking 7-4

Running-in 7-5

Catalytic Converter (if equipped) 7-6

Improving Fuel Economy 7-7

Trailer Towing 7-7

OPERATING YOUR VECHILE

60G-74E

EXHAUST GAS WARNING
DAILY INSPECTION CHECKLIST

60G-07-001E

Avoid breathing exhaust gases.

Exhaust gases contain carbon

monoxide, a potentially lethal gas that

is colourless and odourless. Since

carbon monoxide is difficult to detect

by itself, be sure to take the following

precautions to help prevent carbon

monoxide from entering your vehicle.

• Do not leave the engine running in

garages or other confined areas.

• Do not park with the engine running

for a long period of time, even in an

open area. If it is necessary to sit for

a short time in a parked vehicle <=>
with the engine running, make sure

the air intake lever is set to "FRESH

AIR" and the fan is at high speed.

To allow proper operation of your

vehicle's ventilation system, keep

the air inlet grille in front of the

windscreen clear of snow, leaves, or

other obstructions at all times.

Keep the exhaust tailpipe area clear

of snow and other material to help

reduce the buildup of exhaust gases

under the vehicle.This is particularly

important when parked in blizzard

conditions.

Have the exhaust system inspected

periodically for damage and leaks.

Any damage or leaks should be

repaired immediately.

7-1
70F-05-007

Before driving:

1) Make sure that windows, mirrors, lights,

and reflectors are clean and unobstructed.

2) Check the tyres.

3) Look for fluid and oil leaks.

NOTE:

It is normal for water to drip from the air

conditioning system after use.

4) Adjust the seat/head restraint.

5) Check the brake pedal and the parking

brake lever.

6) Adjust the mirrors.

7) Make sure that you and passengers have

properly fastened your seat belts.

8) Make sure that all warning lights come on

as the key is turned to the "ON" or "START'

position.

9) Check all gauges.

10) Make sure that the brake fluid level

warning light is off when the parking brake

is released with the ignition switch in "ON"

position.

66
65

60G-74E
OPERATING YOUR VEHICLE

Once a week, or each time you fill your fuel

tank, perform the following under-bonnet

checks:

1) Engine oil level.

2) Coolant level.

3) Brake fluid level.

4) Power steering (if equipped) fluid level.

5) Windscreen washer fluid level.

6) Battery solution level.

7) Bonnet latch operation.

Pull the bonnet release handle inside the

vehicle. Make sure that you can not open

the hood all the way without releasing the

secondary latch. Be sure to close the hood

securely after checking for proper

operation. See "All Latches, Hinges &

Locks" of "PERIODIC MAINTENANCE

SCHEDULE" in the "INSPECTION AND

MAINTENANCE" section for lubrication

schedule.

Make sure the bonnet is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
STARTING THE ENGINE

Before starting the engine:

1) Make sure the parking brake is applied

fully.

2) Manual Transmission - Shift into "N"

(neutral) and depress the clutch pedal all

the way to the floor. Hold it while starting

the engine.

Make sure that the parking brake is

applied fully and the transmission is in

Neutral before attempting to start the

engine.

CAUTION

Stop turning the starter immediately

after the engine has started or the

starter system can be damaged.

Do not crank the engine for more

than 15 seconds at a time. If the

engine doesn't start on the first try,

wait about 15 seconds before trying

again.
Starting a Cold Engine

Engine which is started after 6 hours should

be treated as cold engine.

For Electronic fuel injection models

• With your foot off the accelerator pedal,

crank the engine by turning the ignition

key to "START1. Release the key when the

engine starts.

• If the engine does not start after 15

seconds of cranking, wait about 15

seconds, then press down the accelerator

pedal to 1/3 of its travel and try cranking

the engine again. Release the key and

accelerator pedal when the engine starts.

• If the engine still does not start, try holding

the accelerator pedal all the way to the

floor while cranking. This should clear the

engine if it is flooded.

Starting a Warm Engine

For Electronic fuel injection models:

Use the same procedure as for "Starting a cold

Engine".

67

7-2

OPERATING YOUR VECHILE

60G-74E

USING THE TRANSMISSION

70F-04-005E

Starting off

To start off, depress and maintain pressure

upon the clutch pedal and change into 1st

gear. After releasing the parking brake,

gradually release the clutch. When you hear

a change in the engine's sound (speed), gently

apply pressure to the accelerator to keep the

engine sound (speed) constant whilst

continuing to gradually release the clutch.
Gear changing

All forward gears are synchronized, which

provides for quiet, easy changing. Always

depress the clutch pedal fully before changing

gears.The following table shows the maximum

allowable speed for each gear.
GEAR

First

Second

Third

Fourth

Fifth
MAXIMUM SPEED

50 km/h

95 km/h

140 km/h

Top Speed

Top Speed

7-3
68