Cover SUZUKI GRAND VITARA 2000 2.G Service Manual Online

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-5
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER
REAR WIPER AND WASHER (IF EQUIPPED)
TroublePossible causeCorrection
Wiper malfunctions
ªWIPER / WASHERº fuse blown (Hard Top
Model)
ªWIPº fuse blown (Canvas Top Model)

Wiper motor faulty

Wiper switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace motor
Replace switch
Repair
Washer malfunctions
Washer hose or nozzle clogged

ªWIPER / WASHERº fuse blown (Hard Top
Model)
ªWIPº fuse blown (Canvas Top Model)

Washer motor faulty

Washer switch faulty

Wiring faultyClean or repair clogged hose or
nozzle
Replace fuse to check for short
Replace motor
Replace switch
Repair
REAR WINDOW DEFOGGER (IF EQUIPPED)
TroublePossible causeCorrection
Defogger does not work
ªREAR DEFGº fuse blown

Defogger switch faulty

Defogger heat wire faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair heat wire
Repair
POWER WINDOW CONTROL SYSTEM
TroublePossible causeCorrection
All power windows do not
operate
ªPOWER WINDOWº fuse blown (Hard Top
Model)
ªP / Wº fuse blown (Canvas Top Model)

Ignition switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair
Only one power window
does not operate
Power window switch (main or sub) faulty

Power window motor faulty

Window lock switch faulty

Wiring or grounding faultyReplace switch
Replace motor
Replace switch
Repair

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-27
1
1. Immobilizer Control Module
1. Steering column lower cover
1. Coil antenna
IMMOBILIZER CONTROL MODULE
Removal
1) Disconnect negative (±) cable at battery.
2) Remove steering column hole cover.
3) Disconnect coupler at Immobilizer Control Module.
4) Remove Immobilizer Control Module.
Installation
Reverse removal procedure for installation.
NOTE:
After replacing Immobilizer Control Module, be sure to register
Transponder code and ECM/Immobilizer Control Module code
in Immobilizer Control Module and ECM/Immobilizer Control
Module code in ECM / PCM by performing procedure described
in ªProcedure after Immobilizer Control Module Replacementº
section.
COIL ANTENNA
Removal
1) Disconnect negative (±) cable at battery.
2) Remove steering column upper and lower cover by removing 3
screws.
3) Remove steering column hole cover.
4) Remove coil antenna.
Installation
For installation, reverse removal procedure.

YH4
GRAND
VITARA
6. Door trim
7. Door hinge
8. Door open stop
9. Door sealing cover
10. Window regulator handle (if equipped) 1. Door glass
2. Weatherstrip
3. Opening weatherstrip
4. Window regulator
5. Glass run
9-2 BODY SERVICE
GLASS, WINDOWS AND MIRROR
FRONT DOOR GLASS

YH4
GRAND
VITARA
1. Screws 1. Door outside weatherstrip
2. Screw1. Door inside pull handle bracket
BODY SERVICE 9-3
REMOVAL
1) Remove inside handle bezel.
2) Remove door mirror bezel (if equipped).
3) Remove inside lock knob and door inside pull handle case fitting
screw.
3-1) Remove window regulator handle (if equipped).
To remove regulator handle, pull off snap ring by using a cloth
as shown below.
4) Remove door trim.
With inside handle bezel tilted as shown in figure, turn door trim
90
counterclockwise to remove it.
And disconnect power window switch lead wire at coupler (if
equipped).
5) Remove door inside pull handle bracket.
6) Remove door sealing cover.
7) Remove door outside weatherstrip.
Lower window all the way down. Then, use a tape-wrapped putty
knife (or screwdriver) to pry off weatherstrip.
CAUTION:
Use a tape-wrapped putty knife (or screwdriver) to pry off
weatherstrip. Use of an unwrapped tool will cause dam-
age to painting.
8) Remove glass attaching screws.
9) Take out door glass.

YH4
GRAND
VITARA
1. Screws
1. Bolts
1. Door sealing cover
2. Adhesive1, (a)
9-4 BODY SERVICE
INSTALLATION
Reverse removal procedure to install door glass noting following
points:

Tighten glass attaching screws to specified torque. Tighten front
screw first, then rear screw.
Tightening Torque
(a): 2.5 N
.m (0.25 kg-m, 1.8 lb-ft)

When window becomes hard to raise and lower, adjust screws to
correct tilted glass as shown in figure.

Adjust equalizer of window regulator so that measurement A and
B are equal.

Secure door sealing cover with adhesive.

YH4
GRAND
VITARA
1. Eyeleteer
1. Piano string
2. Windshield
3. Windshield knife
BODY SERVICE 9-7
REMOVAL
1) Clean both inside and outside of glass and around it.
2) Remove wiper arms and garnish.
3) Using tape, cover body surface around glass to prevent any
damage.
4) Remove rear view mirror, sunvisor, and front pillar trims (right
& left).
5) If necessary, remove instrument panel. Refer to ªINSTRU-
MENT PANELº in this section.
6) If necessary, remove head lining. Refer to ªHEAD LININGº in
this section.
7) If necessary, remove roof trim. Refer to ªROOF TRIMº in this
section.
8) Remove (or cut) windshield molding all around until windshield
edge comes out.
9) Drill hole with eyeletter through adhesive and let piano string
through it.
10) Cut adhesive all around windshield with piano string.
When using tool to cut adhesive, be careful not to cause dam-
age to windshield. Use wire to cut adhesive along lower part of
windshield.
NOTE:
Use piano string as close to glass as possible so as to pre-
vent damage to body and instrument panel.

YH4
GRAND
VITARA
1. Door trim
2. Inside handle
bezel7. Door hinge
8. Door open stop
9. Door sealing cover
10. Door center sash
11. Partition glass
12. Window regulator handle (if equipped) 1. Door glass
2. Weatherstrip (outside)
3. Glass run
4. Window regulator
5. Partition weather strip
6. Door trim
9-12 BODY SERVICE
REAR DOOR GLASS
REMOVAL
-1) Remove inside handle bezel.
-2) Remove inside lock knob and door inside pull handle case fit-
ting screw.
2-1) Window regulator handle (if equipped).
To remove regulator handle, pull off snap ring by using a cloth
as shown below.
3) Remove door trim with inside weatherstrip.
With inside handle bezel tilted as shown in figure, turn door trim
90
counterclockwise to remove it. And disconnect power win-
dow switch lead wire.
4) Remove door sealing cover.

YH4
GRAND
VITARA
1. Glass
2. Screw
1. Glass run
2. Center sash
3. Partition glass
1. Screw
2. Partition glass
3. Center sash
1. Door outer
weatherstrip
2. Screw
1. Door sealing
cover
2. Adhesive
1
BODY SERVICE 9-13
5) Remove outer weatherstrip.
CAUTION:
Using a tape-wrapped putty knife (or tape-wrapped
screwdriver), pry off weatherstrip. Use of an unwrapped
tool will cause damage to painting.
6) Remove glass fitting screws. Then down door glass.
7) Detach rear part of glass run from center sash.
8) Remove door center sash (by removing two screws with door
glass lowered all the way down).
9) When remove partition glass, slide to front to remove it.
10) Take out glass.
INSTALLATION
Reverse removal sequence to install door glass.
However, be careful of following points.

Securely seal door sealing cover with adhesive.

When weatherstrip is hardened, water leak may develop. In such
case, replace it with new one.

YH4
GRAND
VITARA
9-14 BODY SERVICE
1. Door window
regulator attaching
nuts
2. Hole
1. Window regulator lubrication points
1. Door sealing
cover
2. Adhesive
REAR DOOR WINDOW REGULATOR
REMOVAL
1) Remove door glass, refer to steps 1) to 10) of REAR DOOR
GLASS REMOVAL in this section.
2) Disconnect power window motor lead wire at coupler and clamp.
3) Remove door window regulator attaching nuts (6 pcs.), and take
out regulator through hole as shown in left figure.
INSPECTION
1) Check regulator sliding and rotating parts for greasing.
2) Check rollers for wear and damage.
3) Check wire for damage.
INSTALLATION
Reverse removal sequence to install door window regulator noting
following points.

Tighten regulator base nuts according to the order (a, b, c) shown
in figure.

Adjust door window regulator according to following procedure.
a. Loosen three nuts, two screws and two bolts.
b. Raise window fully.
c. Tighten three regulator rail nuts according to the order (d, e,
f) shown in figure and two center sash bolts A.
d. Lower window.
e. Tighten two screws B to specified torque. Tighten front screw
first, then rear.
Tightening Torque for glass attaching screws
2.5 N
.m (0.25 kg-m, 1.8 lb-ft)
f. Check that the glass moves up and down smoothly and that
the top part of the glass contacts the glass run evenly.

Securely seal door sealing cover with adhesive.

Install door window regulator handle (if equipped) so that it has
an angle as shown when glass is fully closed.

YH4
GRAND
VITARA
9-16 BODY SERVICE
1. Molding
2. Glass
3. Fastener
1. Molding
2. Glass
3. Primer
4. Adhesive
5. Fastener
1. Door sealing cover
BACK DOOR GLASS
REMOVAL AND INSTALLATION
Refer to ªWINDSHIELDº section as removal and installation proce-
dures and cautions are basically the same. However, note the fol-
lowing.
NOTE:

Before applying primer to glass edge, install molding ac-
cording to installing position shown in figure.

Observe following precautions when applying adhesive
along glass edge.
±Adhesive should be applied evenly especially in height.
±Be careful not to damage primer.
±Press glass against body quickly after adhesive is applied.
Height ªbº : 15 mm (0.59 in.)
Width ªcº : 8 mm (0.31 in.)
Width ªdº : 16 mm (0.63 in.)
Clearance ªeº : 1 mm (0.04 in.)

When replacing back door, coat replacement door inside
with wax for proper anticorrosive treatment. Refer to ªUN-
DER COATING / ANTI-CORROSION COMPOUND APPLICA-
TION AREAº in this section.

Apply sealing compound to peripheral of door hem area and
reinstall door sealing cover.

When weatherstrip is hardened and water leaks have devel-
oped, replace it.