key TOYOTA AVALON 2001 Service Repair Manual

AT8748
D02459
21
D07236
P
P2
P1
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Column Shift)
AX-19
1309 Author
: Date
:
2001 AVALON (RM808U)
3. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals.
Standard resistance: 12.5 -16.5 W
If resistance value is not as specified, replace the solenoid.
(c) Supply battery positive voltage between terminals.
If the solenoid does not operate, replace the solenoid.
4. INSPECT SHIFT LOCK CONTROL SWITCH
Inspect that continuity between at each terminal.
Shift positionTester connectionSpecified value
P position (Release button
is not pushed)3 (P1) - 1 (P)Continuity
P position (Release button
is pushed)3 (P1) - 1 (P)
4 (P2) - 1 (P)Continuity
R, N, D, 2, L position4 (P2) - 1 (P)Continuity
If continuity is not specified, replace the switch.

AX03T-04
D07231
Shift Lock Control Switch
Key Interlock Solenoid
Stop Light Switch Shift Lock Solenoid
Shift Lock Control ECU
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Column Shift)
AX-17
1307 Author
: Date
:
2001 AVALON (RM808U)
SHIFT LOCK SYSTEM (Column Shift)
LOCATION

AX0CT-02
Q09455Wire harness side: 5 (IG)
4 (KLS
+)
3 (E)
2 (STP)1 (ACC)
Q09456
1 (KLS+)
2 (E)
Q09457(-) (+)1 (KLS
+)
2 (E) AX-16
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Floor Shift)
1306 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY
Using a voltmeter, measure the voltage at each terminal.
HINT:
Do not disconnect the shift lock control unit assembly connec-
tor.
Terminal (Symbol)Measuring ConditionVoltage (V)
1 (ACC) - 3 (E)Ignition switch ACC10 - 14
5 (IG) - 3 (E)Ignition switch ON10 - 14
2 (STP) - 3 (E)Depressing brake pedal10 - 14
4 (KLS+) - 3 (E)
(1) Ignition switch ACC and P position
(2) Ignition switch ACC and except P position
(3) Ignition switch ACC and except P position (After approx. 1 second)0
7.5 - 11
6 - 9.5
2. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure resistance between termi-
nals.
Standard resistance: 14.5 ± 1.5 W
If resistance value is not as specified, replace the solenoid.
(c) Apply battery positive voltage between terminals. Check
that an operation noise can be heard from the solenoid.
If the solenoid does not operated, replace the solenoid.

AX0CS-02
D07232
Key Interlock Solenoid
Stop Light Switch
Shift Lock Control
Unit Assembly
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Floor Shift)
AX-15
1305 Author
: Date
:
2001 AVALON (RM808U)
SHIFT LOCK SYSTEM (Floor Shift)
LOCATION

I19691
ºTUNE DOWNº Switch
º1chº Switch º2chº Switch º3chº Switchº4chº Switch º5chº Switchº6chº Switch
ºDISCº Switch
ºTUNE UPº Switch
- BODY ELECTRICALAUDIO SYSTEM
BE-133
1737 Author
: Date
:
2001 AVALON (RM808U)
2. Except Europe models:
DIAGNOSIS FUNCTION
Error codes over tuner and connected equipment are displayed on the screen of tuner.
(a) Diagnosis start-up
For shifting to diagnosis mode, push ºDISCº switch 3 times with pressing º1º and º6º of PRESET switch
at the same time while the audio power is OFF and ACC is ON.
To exit from diagnosis mode, press ºDISCº switch for 2 seconds or turn the ignition key OFF.
(When º1-190º is displayed, the mode is transferred to LAN check mode.)
(b) LAN check
When starting up the diagnosis mode, the mode turns to LAN check mode, the screen displays the
code numbers (physical address) of tuner and connected equipment. Smaller codes are displayed in
order, displayed code numbers are switched by operating TUNE ºUPº or ºDOWNº switch. In LAN check
mode, by pressing º5º of PRESET switch for more than 2 secs., diagnosis memory of each equipment
can be deleted, when deletion is completed, the mode returns to LAN check mode.
Code No. (physical address) List
Code No. (physical address)Equipment name
190Radio receiver assembly (Audio head unit)
240CD changer (in Luggage room)
360CD changer (in center console and glove compartment box)
440Power amplifier
(c) System check
When pressing º1º of PRESET switch in LAN check mode, the mode turns to the system check
mode, the system performs self diagnosis of connected equipment and displays the re-
sults.(ºSYSº (showing the system is under detection) is displayed.)
Perform the operation shown in the following illustration, then read the result of the inspection.

BE-136
- BODY ELECTRICALAUDIO SYSTEM
1740 Author
: Date
:
2001 AVALON (RM808U)
3. Europe models:
DIAGNOSIS CODE LIST
TermsMeaning
Physical addressThree-digit code (shown in hexadecimal) which is given to each component com-
prising the AVC-LAN.
Corresponding to the function, individual symbols are specified.
Logical addressTwo-digit code (shown in hexadecimal) which is given to each function comprising
the inner system of the AVC-LAN.
(a) Physical address 190: Radio receiver assembly
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It is stored when 180 sec. has passed after the power supply connector is pulled out after engine
start.
*3: It may be stored when the engine key is turned 1 min. again after engine start.
*4: It may be stored when the engine key is turned again after engine start.
*5: When 210 sec. has passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.
(1) Logical address: 01 (Communication control)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
D6
*1Absence of MasterComponent in which this code is recorded
has been disconnected from system with
ignition in ACC or ON. Or, when this code
was recorded, multi-display assembly was
disconnected.Check harness for power supply system of
multi-display.
Check harness for communication system
of multi-display.
Check harness for power supply system of
radio and player.
Check harness for communication system
of radio and player.
D8
*2No Response to Connection CheckComponent shown by auxiliary code is or
had been disconnected from system after
engine is start.
D9Check harness for power supply system of
component shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
D9
*1Last Mode ErrorComponent operated (sounds and/or
images were provided) before engine stop is
or has been disconnected with ignition
switch in ACC or ON.Check harness for power supply system of
component shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
DANo Response to ON/OFF InstructionNo response is identified when changing
mode (audio and visual mode change).
Detected when sound and picture does not
change by button operation.Check harness for power supply system of
component shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
If error occurs again, replace component
shown by auxiliary code.
DB
*1Mode Status ErrorDual alarm is detected.Check harness for power supply of compo-
nent shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
DC
*3Transmission ErrorTransmission to component shown by auxil-
iary code has been failed.
(Detecting this DTC does not necessarily
mean actual failure.)If same auxiliary code is recorded in order
component, check harness for power supply
and communication system of all compo-
nents shown by code.

- BODY ELECTRICALAUDIO SYSTEM
BE-137
1741 Author
: Date
:
2001 AVALON (RM808U) DD
*4
Master Reset (Momentary Interruption)After engine is started, multi-display assem-
bly was disconnected from system.Check harness for power supply system of
multi-display.
Check harness for communication system
of multi-display.
Check harness for power supply system of
radio and player.
Check harness for communication system
of radio and player.
If this error occurs frequently, replace mul-
ti-display assembly.
DE
*4Slave Reset (Momentary Interruption)After engine is started, slave component
was disconnected from system.Check harness for power supply of compo-
nent shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
DF
*5Master ErrorDue to defective condition of component
with a display, master function is switched to
audio equipment.
Error occurs in communication between
sub-master (audio) and master component.Check harness for power supply of multi-
display assembly.
Check harness for communication system
of multi-display assembly.
Check harness for communication system
between multi-display assembly and sub-
master component.
E0
*1Registration Completion Instruction ErrorºRegistration Completion Instructionº com-
mand from master cannot be received.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
E1
*1Audio processor ON errorWhile source equipment is operating, AMP
output is stopped.Check harness for power supply of multi-
display assembly.
Check harness for communication system
of multi-display assembly.
E2ON/OFF Instruction Parameter ErrorError occurs in ON/OFF controlling com-
mand from multi-display assembly.Replace multi-display assembly.
E3
*1Registration Request TransmissionRegistration Request command is output
from slave component.
Receiving Connection Check Instruction,
Registration Request command is output
from sub-master component.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
(2) Logical address: 61 (Cassette switch)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
40Mechanical of Media ErrorMalfunction due to mechanical failure is
identified.
Or cassette tape is cut or entangled.Inspect cassette tape.
Replace radio and player.
(b) Physical address: 440 Stereo component amplifier
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It may be stored when the engine key is turned 1 min. again after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.

BE-138
- BODY ELECTRICALAUDIO SYSTEM
1742 Author
: Date
:
2001 AVALON (RM808U)
Logical address: 01 (Communication control)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
D6
*1Absence of MasterComponent in which this code is recorded
has been disconnected from system with
ignition in ACC or ON. Or, when this code
was recorded, multi-display assembly was
disconnected.Check harness for power supply of radio
and player.
Check harness for communication system
of radio and player.
Check harness for power supply of stereo
component amplifier.
Check harness for communication system
of stereo component amplifier.
D4Communication Check ErrorComponent in which this code is recorded is
or was disconnected from system after en-
gine start. Or, when recording this code,
multi-display assembly was disconnected.Check harness for power supply of radio
and player.
Check harness for communication system
of radio and player.
Check harness for power supply of stereo
component amplifier.
Check harness for communication system
of stereo component amplifier.
D1
*2Transmission ErrorTransmission to component shown by auxil-
iary code has been failed.
(Detecting this DTC does not necessarily
mean actual failure.)If same auxiliary code is recorded in order
component, check harness for power supply
and communication system of all compo-
nents shown by code.
(c) Physical address: 240 CD Auto Changer
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It may be stored when the engine key is turned 1 min. again after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: It may be stored when the engine key is turned again after engine start.
*5: When 210 sec. has passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.
(1) Logical address: 01 (Communication control)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
DITransmission ErrorTransmission to component shown by auxil-
iary code has been failed.
(This code does not necessarily mean actu-
al failure.)If same auxiliary code is recorded in other
component(s), check harness for power
supply and communication system of com-
ponents shown sub code.
D4
*5Connection check Error
Component in which this code is recorded is
or was disconnected from system after en-
gine start. Or, when recording this code,
multi-display assembly was disconnected.Check harness for power supply of multi-
display.
Check harness for communication system
of multi-display.
Check harness for power supply of CD
auto changer.
Check harness for communication system
of CD auto changer.
(2) Logical address: 63 (CD Auto Changer)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
60CD ErrorError is detected in CD auto changer.Replace CD auto changer
61EJECT ErrorMagazine cannot be ejected.Replace CD auto changer
62No Disc ReadoutDisc cannot be read.Inspect CD

I03099
BE0B4-04
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE-181
1785 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
INSPECTION TRANSPONDER KEY COIL CONTINUITY
Check that continuity exists between terminal 1 and 2.
If continuity is not as specified, replace the coil.

BE0B3-1 1
I12540
Driver Side Junction Block

IGN Relay
Ignition Switch Assembly

Transponder Key Amplifier

Transponder Key Coil

Key Unlock Warning SwitchEngine Room Junction Block

EFI No. 2 Fuse
ECM
BE-180
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
1784 Author
: Date
:
2001 AVALON (RM808U)
LOCATION