key TOYOTA AVALON 2001 Service Owner's Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 256 of 1897
BE1EH-01
I03433
Not turned
Unlock
I13485
1
2
I13334
I04020
1
- BODY ELECTRICALLUGGAGE COMPARTMENT DOOR OPENER SYSTEM
BE-125
1729 Author: Date:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT LUGGAGE COMPARTMENT DOOR KEY
LOCK AND UNLOCK SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Not turned-No continuity
UNLOCK1 - 2Continuity
If continuity is not as specified, replace the switch.
2. INSPECT LUGGAGE COMPARTMENT DOOR OPEN-
ER MAIN SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF-No continuity
ON1 - 2Continuity
If continuity is not as specified, replace the switch.
3. INSPECT LUGGAGE COMPARTMENT DOOR OPEN-
ER CANCEL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF-No continuity
ON1 - 2Continuity
If continuity is not as specified, replace the switch.
4. INSPECT LUGGAGE COMPARTMENT DOOR OPEN-
ER MOTOR OPERATION
Connect positive (+) lead to the terminal 1 and negative (-) lead
to the opener motor body, and check that the motor operateds.
If operation is not as specified, replace the lock.
Page 258 of 1897
BE212-01
BE-88
- BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
1692 Author: Date:
ADJUSTMENT
ENABLING/DISABLING AUTO DOOR LOCK FUNCTION
(a) To disable auto door lock:
(1) Enter the vehicle and shut all doors.
(2) Insert the key into the ignition cylinder and turn it to
the ON position (not ACC).
(3) Open the driver's door and keep it open.
(4) Turn the key to the LOCK position and remove it
from the ignition cylinder.
(5) Insert the key into the ignition cylinder and remove
it. Repeat this operation three more times. (End this
step with the key out of the ignition cylinder.)
(6) Push the ºUNLOCKº button on the driver's door
master switch 5 times within 10 seconds. Wait at
least 10 seconds and shut the driver's door.
(7) Verify auto lock operation has been disabled by
starting the engine, putting the vehicle into a gear
and releasing the brake pedal.
(b) To enable auto door lock:
Follow the same sequence as above, except step 6. In step 6,
push the ºLOCKº button on the driver's door master switch 5
times within 10 seconds. Wait at least 10 seconds and shut the
driver 's door.
Page 259 of 1897
I12841
UNLOCKLOCK1 2 3 4 5 6
BE1DY-02
I12842
LOCK
UNLOCK1 2 3 4 5 6
I12843
UNLOCK
1 2 3 4 5 6
I12844
UNLOCK
1 2 3 4 5 6
I07301
LOCK
BE-82
- BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
1686 Author: Date:
2001 AVALON (RM808U)
INSPECTION
1. Driver 's door:
INSPECT DOOR KEY LOCK AND UNLOCK SWITCH
CONTINUITY
Switch positionTester connectionSpecified condition
LOCK3 - 5Continuity
OFF-No continuity
UNLOCK3 - 6Continuity
If continuity is not as specified, replace the switch.
2. Passenger 's Door:
INSPECT DOOR KEY LOCK AND UNLOCK SWITCH
CONTINUITY
Switch positionTester connectionSpecified condition
LOCK2 - 4Continuity
OFF-No continuity
UNLOCK1 - 4Continuity
If continuity is not as specified, replace the switch.
3. Driver 's Door:
INSPECT DOOR UNLOCK DETECTION SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
OFF (Door Lock set to
LOCK)-No continuity
ON (Door Lock set to
UNLOCK)3 - 4Continuity
If continuity is not as specified, replace the switch.
4. Passenger 's Door:
INSPECT DOOR UNLOCK DETECTION SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
OFF (Door Lock set to
LOCK)-No continuity
ON (Door Lock set to
UNLOCK)3 - 4Continuity
If continuity is not as specified, replace the switch.
5. Rear LH Door:
INSPECT DOOR UNLOCK DETECTION SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
OFF (Door Lock set to
LOCK)-No continuity
ON (Door Lock set to
UNLOCK)1 - 2Continuity
If continuity is not as specified, replace the switch.
Page 265 of 1897
BE0IJ-03
I12855
Driver Side Junction Block
Door No.1 Fuse
Body ECUIgnition Switch
Front Door Lock Assembly
Door Lock Motor
Door Unlock Detection Motor
Door Key Lock and Unlock Switch
Rear Door Lock Assembly
Door Lock Motor
Door Unlock Detection Switch
Power Window Master Switch
Door Lock Control Switch
Driver Door ECU
- BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
BE-81
1685 Author: Date:
2001 AVALON (RM808U)
POWER DOOR LOCK CONTROL SYSTEM
LOCATION
Page 306 of 1897
BE04Q-06
BE-2
- BODY ELECTRICALTROUBLESHOOTING
1606 Author: Date:
2001 AVALON (RM808U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
POWER OUTLET
SymptomSuspect AreaSee page
Electric power source cannot be taken out of the power outlet11. PWR OUTLET No. 1, 2 Fuse
12.Wire Harness-
-
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
HEADLIGHT AND TAILLIGHT SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
FOG LIGHT SYSTEM:
SymptomSuspect AreaSee page
Fog light does not light with light control SW HEAD.
(Headlight is normal)
1. FOG Fuse
2. Fog Light Relay
3. Fog Light Switch
4. Wire Harness-
BE-26
BE-26
-
Fog light does not light with light control SW HEAD.
(Headlight does not light)1. Other Parts*1
2. Wire Harness
-
-
Only one light does not light.1. Bulb
2. Wire Harness-
-
*1: Inspect Headlight System.
TURN SIGNAL AND HAZARD WARNING SYSTEM:
SymptomSuspect AreaSee page
ºHazardº and ºTurnº do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher
3. Wire HarnessBE-29
BE-29
-
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Switch
3. Wire Harness-
BE-29
-
Hazard warning light does not light up.
(Turn is normal.)1. HAZ Fuse
2. Wire Harness-
-
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE-29
-
*1Turn signal does not light up.
1. Ignition Switch
2. TURN Fuse
3. Turn Signal Switch
4. Wire HarnessBE-16
-
BE-29
-
*2Turn signal does not light up.
1. TURN Fuse
2. Turn Signal Switch
3. Wire Harness-
BE-29
-
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE-29
-
Only one bulb does not light up.1. Bulb
2. Wire Harness-
-
*1: Combination Meter, Wiper and Washer do not operate.
*
2: Combination Meter, Wiper and Washer are normal.
Page 311 of 1897
- BODY ELECTRICALTROUBLESHOOTING
BE-7
1611 Author: Date:
2001 AVALON (RM808U)
WIRELESS DOOR LOCK CONTROL SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
Some functions of wireless door lock control system do not operate.
HINT:
Troubleshooting of the wireless door lock control system is based on the premise that the door lock
control system is operating normally. Accordingly, before troubleshooting the wireless door lock control
system, first make certain that the door lock control system is operating normally.
If the trouble still reappears even though there are no abnormalities in any of the other circuits, then
check and replace the Wireless Door Lock Control Receiver as the last step.
SLIDING ROOF SYSTEM:
SymptomSuspect AreaSee page
Sliding roof system does not operate.
(Door Lock does not operate)1. SUN ROOF Fuse
2. GAUGE Fuse
3. Wire Harness-
-
-
Sliding roof system does not operate.
(Door Lock is normal)
1. Sliding Roof Control Switch
2. Sliding Roof Motor and Limit Switch
3. Sliding Roof Control Relay
4. Wire HarnessBE-103
BE-103
BE-103
-
Sliding roof system operates abnormally.
1. Sliding Roof Control Switch
2. Sliding Roof Motor and Limit Switch
3. Sliding Roof Control Relay
4. Wire HarnessBE-103
BE-103
BE-103
-
Sliding roof system stops operation half way.
(Stones of foreign material trapped in motor assembly)1. Sliding Roof Control Relay and Switch
2. Sliding Roof Motor and Limit Switch
3. Wire HarnessBE-103
BE-103
-
ºKey-of f Sliding Roofº operation does not operate.
1. DOOR Fuse
2. GAUGE Fuse
3. Ignition Switch
4. Body ECU
5. Wire Harness-
-
BE-16
BE-16
-
POWER SEAT CONTROL SYSTEM (w/o Driving position memory driver's seat):
SymptomSuspect AreaSee page
Power seat does not operate.
(Door lock system does not operate)1. DOOR Fuse
2. Wire Harness-
-
Power seat does not operate.
(Door lock system is normal)1. Power Seat Swtich (D,P)
2. Wire HarnessBE-105
-
ºSlide operationº does not operate.
1. Power Seat Switch (D, P)
2. Slide Motor (D, P)
3. Wire HarnessBE-16
BE-105
-
ºFront vertical Operationº does not operate.
1. Power Seat Switch (D, P)
2. Front Vertical Motor (D, P)
3. Wire HarnessBE-105
BE-105
-
ºRear verticalº does not operate.
1. Power Seat Switch
2. Rear Vertical Motor
3. Wire HarnessBE-105
BE-105
-
ºReclining Operationº does not operate.
1. Power Seat Switch (D, P)
2. Reclining Motor (D, P)
3. Wire HarnessBE-105
BE-105
-
(D): Driver's Seat
(P): Passenger's Seat
Page 319 of 1897
BE2MA-01
I20790
Key Plate Inserted
ON
OFFWithin. 5 sec.
1 Key Plate Not Inserted
23 910Within. 30 sec.
Once Nine times
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-91
1695 Author: Date:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT WIRELESS DOOR LOCK DIAGNOSIS MODE
(a) Start up diagnosis mode.
HINT:
Follow the method below.
(1) Insert the ignition key into the ignition key cylinder.
(2) Remove the ignition key from the ignition key cylin-
der.
(3) Insert the key into the ignition switch.
(4) Turn the ignition switch ON once within 5 sec.
(5) Repeat turning the ignition switch OFF " ON 9
times within 30 sec.
(6) Enter the diagnosis mode, and make sure that the
buzzer sounds.
(b) Finishing the Diagnosis Mode.
During the Diagnosis mode, turn the ignition switch OFF
" ON to go back to the normal mode.
At this time make sure that the buzzer sounds.
Page 320 of 1897
I20456
(1) LOCK switch
(2) UNLOCK switch
(3) Luggage door switch
(4) Disagreement of recognition code or
rolling code.
0.13 sec.
0.5 sec.
0.13 sec. 0.25 sec. 0.5 sec.
0.5 sec. 0.5 sec.
OFF ON
OFF ON
OFF ON
OFF ON
While receiving
I06938
Dry cell battery (1.5 V x 2)
Push BE-92
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
1696 Author: Date:
2001 AVALON (RM808U)
(c) Diagnosis Mode Check.
HINT:
Check how the buzzer sounds when pressing each transmitter
switch.
(1) LOCK switch
(2) UNLOCK switch
(3) Luggage door switch
(4) Disagreement of recognition code or rolling code.
HINT:
If (4) is detected in the Diagnosis Check, conduct the recogni-
tion code registration.
(5) No response from the buzzer.
HINT:
Conduct the following checks.
Check the wireless door lock transmitter.
Check the wireless door lock receiver.
2. INSPECT WIRELESS DOOR LOCK TRANSMITTER
OPERATION
HINT:
Refer to ºWireless door lock control receiver and transmitter re-
placementº.
(a) Using a screwdriver, remove the cover.
(b) Remove the battery (lithium battery).
(c) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery can not be obtained, connect 2
new 1.5 V batteries in series, connect the battery (+) to the bat-
tery receptacle side terminal and battery (-) to the bottom termi-
nal, then apply 3 V voltage to the transmitter.
(d) In the location where is approx. 1 M away from driver's
outside handle in the right direction, face the key plate of
the transmitter to the vehicle, and check the transmitter
operation when pressing transmission switch on the side
of the transmitter body.
Standard:
Remote control of vehicle door lock can be operated.
LED lights up more than once.
HINT:
The minimum operation distance differs according to op-
erator, the way of holding, and location.
As weak wave is used, operation distance might be short-
ened when noise is detected in strong wave or used fre-
quency.
Page 323 of 1897
I04152
Wire Harness Side
I04153
From Back Side
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-95
1699 Author: Date:
2001 AVALON (RM808U)
8. Connector disconnected:
INSPECT WIRELESS DOOR LOCK CONTROL RE-
CEIVER CIRCUIT
Disconnect the connector from the receiver and inspect the
connector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
1 - GroundConstantContinuity
7 - GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuit connected to
other parts.
9. Connector connected:
INSPECT WIRELESS DOOR LOCK CONTROL RE-
CEIVER CIRCUIT
Connect the wire harness side connector to the receiver and in-
spect the wire harness side connector from the back side, as
shown.
Tester connectionConditionSpecified condition
3 - Ground
Ignition switch position OFF
Key removed
Transmitter OFF " ON
4.5 - 5.5 V " below 1 V
4 - Ground
Ignition switch position OFF
Key removed
Transmitter OFF
10 - 14 V
If circuit is as specified, replace the receiver.
If the circuit is not as specified, inspect the circuit connected to
other parts.
Page 326 of 1897
BE2M9-01
I06940
I06941
BE-96
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
1700 Author: Date:
2001 AVALON (RM808U)
REPLACEMENT
1. REPLACE TRANSMITTER (LITHIUM) BATTERY
NOTICE:
Special caution should be taken for handling each compo-
nent as they are precision electronic components.
(a) Using a screwdriver, remove the cover.
NOTICE:
Do not pry out the cover forcibly.
HINT:
Push the cover with a finger as shown in the illustration, so that
there becomes clearance, then pry out the cover from that
clearance.
(b) Remove the transmitter.
(c) Remove the battery (lithium battery).
NOTICE:
Do not push the terminals with a finger.
If prying up the battery (lithium battery) forcibly to re-
move, the terminals are deformed.
(d) Install a battery (lithium battery) as shown in the illustra-
tion.
NOTICE:
Face the battery upward. Take care not to deform the termi-
nals.
(e) Assemble the transmitter to the key plate and the cover.