TOYOTA AYGO 2021 Owners Manual

992. Instrument cluster
2
Instrument cluster
AYGO_OM_Europe_OM9A012E
Warning lights inform the driver of malfunctions in the indicated vehi-
cle’s systems.
Warning lights
*1Brake system warning
light ( P. 449)
*1Electric power steering
system warning light
( P. 451)
*1
Charging system
warning light ( P. 449)
*1, 2, 4
PCS warning light
( P. 452)
*1
Low engine oil pressure
warning light ( P. 449)
*2, 3
(Yellow)
Speed limiter indicator
( P. 452)
*1High engine coolant
temperature warning
light ( P. 450)
*1, 2, 4
Stop & Start cancel
indicator ( P. 452)
*1“STOP” warning light
( P. 450)
*1
Slip indicator light
( P. 453)
*1, 2Multi-mode manual
transmission
warning light ( P. 450)
*2
(Yellow)
LDA indicator (P. 453)
*1, 2, 4
Heat clutch warning light
( P. 450)
*2, 7
(Yellow)
Lane marker indicators
( P. 453)
*1
Malfunction indicator
lamp ( P. 451)
*2, 5
(Yellow)
Smart entry & start
system indicator light
( P. 453, 457)
*1SRS warning light
( P. 451)
Open door warning light
( P. 453)
*1
ABS warning light
( P. 451)
Driver’s and front pas-
senger’s seat belt
reminder light ( P. 453)

1002. Instrument cluster
AYGO_OM_Europe_OM9A012E
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system), to indicate that a system check
is being performed. They will turn off after the engine is started, or after a
few seconds. There may be a malfunction in a system if a light does not
come on, or turn off. Have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable repairer.
*2: If equipped
*3: The light comes in yellow to indicate a malfunction.
*4: The light flashes to indicate a malfunction.
*5: The light flashes in yellow to indicate a malfunction. The light flashes
quickly in green to indicate that the steering lock has not been released.
*6: This light illuminates on the center panel.
*7: The lights turn on with LDA indicator to indicate a malfunction.
The indicators inform the driver of the operating state of the vehicle’s
various systems.
*6Rear passengers’ seat
belt reminder lights
(P. 453)*1, 2
Tire pressure warning
light (P. 454)
Low fuel level warning
light (P. 454)
Indicators
*1Gear Shift indicator
(P. 224, 227)Headlight high beam
indicator (P. 232)
Turn signal indicator
(P. 229)
*2Front fog light indicator
(P. 235)
*2
(Green)
Smart entry & start
system indicator light
(P. 217)Rear fog light indicator
(P. 235)
Tail light indicator
(P. 231)
*1, 3Slip indicator light
(P. 280)

1012. Instrument cluster
2
Instrument cluster
AYGO_OM_Europe_OM9A012E
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system), to indicate that a system check
is being performed. They will turn off after the engine is started, or after a
few seconds. There may be a malfunction in a system if a light does not
come on, or turn off. Have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable repairer.
*2: If equipped
*3: The light flashes to indicate that the system is operating.
*4: This light illuminates on the center panel.
*5: The light comes on when the system is turned off.
*6: The light comes on when system settings are changed.
*7: The light flashes in yellow to indicate that the vehicle is deviating from the
lane.
*1VSC off indicator
( P. 280)
*1, 2Stop & Start cancel
indicator ( P. 273)
*2
(Green)
Speed limiter indicator
light ( P. 269)
*1, 2
“TRC OFF” indicator
( P. 280)
*2
(Green)
LDA indicator (P. 264)
*2, 3, 6
PCS activation indicator
( P. 251, 254)
*2, 7
(Green)
Lane marker indicators
( P. 265)
*1, 2, 5
PCS warning light
( P. 254)
*1, 2
Stop & Start indicator
light ( P. 272) “PASSENGER AIR BAG” indicator
( P. 4 9 )
*1, 4

1022. Instrument cluster
AYGO_OM_Europe_OM9A012E
WARNING
■If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable repairer immediately if
this occurs.
NOTICE
■ To prevent damage to the engine and its components
The engine may be overheating if the high engine coolant temperature
warning light flashes or turns on. In this case, immediately stop the vehicle
in a safe place, and check the engine after it has cooled completely.
( P. 5 0 4 )

103
2
2. Instrument cluster
Instrument cluster
AYGO_OM_Europe_OM9A012E
Gauges and meters
Vehicles without a tachometer
The units used on the speedometer may differ depending on the target
region.
Speedometer
Displays the vehicle speed
Fuel gauge
Displays the quantity of fuel remaining in the tank
“DISP” buttons
P. 105
Drive monitor display
Presents the driver with a variety of driving-related data (P. 105)
1
2
3
4

1042. Instrument cluster
AYGO_OM_Europe_OM9A012E
Vehicles with a tachometer
The units used on the speedometer may differ depending on the target
region.
Tachometer
Displays the engine speed in revolutions per minute
Speedometer
Displays the vehicle speed
Fuel gauge
Displays the quantity of fuel remaining in the tank
“DISP” buttons
 P. 105
Drive monitor display
Presents the driver with a variety of driving-related data (P. 105)
NOTICE
■To prevent damage to the engine and its components
Do not let the indicator level of the tachometer enter the red zone, which
indicates the maximum engine speed.
1
2
3
4
5

105
2
2. Instrument cluster
Instrument cluster
AYGO_OM_Europe_OM9A012E
Drive monitor display
The drive monitor display presents the driver with a variety of driving-
related data including the current outside air temperature.
●Outside temperature display
(P. 375)
●Trip information (P. 105)
Displays driving range, fuel con-
sumption and other cruising related
information
●Instrument cluster light control
(P. 108)
●Shift position (vehicles with a multi-mode manual transmission)
Displays the selected shift position (P. 222)
●Speed limiter display (if equipped) (P. 269)
■Switching the display
Items displayed can be
switched by pushing one of the
“DISP” buttons.
Forward
Backward
■Odometer
Displays the total distance the vehicle has been driven.
Display contents
Trip information
1
2

1062. Instrument cluster
AYGO_OM_Europe_OM9A012E■
Trip meters “A” and “B”
Displays the distance the vehicle has been driven since the meter
was last reset. Trip meters “A” and “B” can be used to record and
display different distances independently.
Push and holding one of the “DISP” buttons will reset the trip meter that
is currently displayed.
■
Stop & Start system operation time (if equipped)
●Displays the amount of time the engine was stopped due to oper-
ation of the Stop & Start system during the current trip.
Vehicles without a smart entry & start system: From the engine switch in
the “ON” position to the engine switch in the “LOCK” position.
Vehicles with a smart entry & start system: From the engine switch in
IGNITION ON mode to the engine switch off.
●When the Stop & Start system is operating, the presently dis-
played screen is interrupted and the Stop & Start system opera-
tion time automatically displayed.
• Push one of the “DISP” buttons to return to the previous screen.
• The automatically displayed function of the Stop & Start system oper-
ation time activated or deactivated switch over method. (P. 108)
■
Stop & Start system total operation time (if equipped)
Displays the total amount of time that the engine has been stopped
due to operation of the Stop & Start system since the system was
last reset.
Push and hold one of the “DISP” buttons to reset.
■Outside temperature (vehicles with a multi-mode manual
transmission)
Displays the outside temperature. (
P. 375)
■Current fuel consumption
Displays the current rate of fuel consumption.

1072. Instrument cluster
2
Instrument cluster
AYGO_OM_Europe_OM9A012E■
Average fuel consumption
Displays the average fuel consumption since the function was
reset.
• The function can be reset by pushing one of the “DISP” buttons for lon-
ger than 1 second when the average fuel consumption is displayed.
• Use the displayed average fuel consumption as a reference.
■
Driving range
Displays the estimated approximate distance that can be driven
with the quantity of fuel remaining.
• This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
• When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the engine switch to the “LOCK” position (vehicles
without a smart entry & start system) or off (vehicles with a smart entry
& start system). If the vehicle is refueled without turning the engine
switch to the “LOCK” position or off, the display may not be updated.
• The display shows “LoFUEL” when the remaining is very low.
■
Average vehicle speed
Displays the average vehicle speed since the function was reset.
The function can be reset by pushing one of the “DISP” button for longer
than 1 second when the average vehicle speed is displayed.
■
Instrument cluster light control
Displays the instrument cluster light control display.
• This screen is only displayed when the tail lights are on.
• The brightness of the instrument cluster light can be adjusted.
(P. 108)

1082. Instrument cluster
AYGO_OM_Europe_OM9A012E
The automatically displayed function of the Stop & Start system oper-
ation time can be activated or deactivated.
Push one of the “DISP” buttons and the Stop & Start system opera-
tion time is displayed, while the vehicle is stopped.
Push and hold the “DISP” buttons for 5 seconds.
Push the “DISP” buttons to
switch activate or deactivate.
Activated
Deactivated
The screen will change back to the
previous screen after 6 seconds or
by push and holding one of the
“DISP” buttons for 2 seconds.
Push the one of the “DISP” buttons and the instrument cluster light
control display while the tail lights is turned on and vehicle is
stopped.
Push and hold one of the “DISP” buttons until instrument cluster
light control display flashes.
Push one of the “DISP” buttons.
Brighter
Darker
The illumination level can be set by
push and holding one of the “DISP”
buttons, turning off the tail lights, or
automatically 6 seconds after the
last button push has elapsed.
Stop & Start system operation time customization (if equipped)
1
2
Instrument cluster light control
1
2