roof rack TOYOTA CAMRY 1999 Service Repair Manual

BO0LE±01
N22588
121
N21430
: 4 Clips
N22591
BO±28
± BODYLUGGAGE COMPARTMENT DOOR AND HINGE
2376 Author: Date:
REMOVAL
1. REMOVE LUGGAGE COMPARTMENT DOOR TRIM
2. REMOVE LUGGAGE COMPARTMENT DOOR
(a) Disconnect the connector.
(b) Using a clip remover, disconnect the clamps.
(c) Remove the 4 bolts and door.
Torque: 8.0 N´m (80 kgf´cm, 71 in.´lbf)
3. REMOVE THESE PARTS:
(a) Luggage compartment floor mat
(b) LH and RH rear floor finish side plates
(c) Inner cover trims
(d) Rear seat
(e) Room partition trims
4. REMOVE HIGH±MOUNTED STOP LIGHT
(a) Push on the both side of the cover to release the claws by
your hand and remove the cover as shown in the illustra-
tion.
(b) Remove the 2 bolts and stop light, then disconnect the
connector.
5. REMOVE ROOF SIDE INNER GARNISH
(a) Remove the clip.
(b) Using a screwdriver, pry loose and remove the garnish.
HINT:
Tape the screwdriver tip before use.
6. REMOVE PACKAGE TRAY TRIM
7. REMOVE TORSION BAR
(a) Remove the torsion bar from the center bracket.

BO0LI±01
H01754
H01755
H01756
N21430
: 4 clips
± BODYLUGGAGE COMPARTMENT DOOR AND HINGE
BO±33
2381 Author: Date:
INSTALLATION
1. INSTALL TORSION BAR
(a) Insert the torsion bar into the bracket.
HINT:
The center bracket opening is the nominal position of the tor-
sion bar.
If needed, move the torsion bar to the upper or lower hole to pro-
vide the correct luggage door lift.
(b) Install the SST onto the torsion bar of the hinge side.
SST 09804±24010
(c) Slowly lift the torsion bar with the SST and place it in the
torsion bar bracket.
(d) Slowly push the SST down and install the torsion bar to
the hinge.
(e) Slowly lift the SST and install the torsion bar.
(f) Install the torsion bar to the center bracket.
(g) Repeat for the other side.
2. INSTALL PACKAGE TRAY TRIM
3. INSTALL ROOF SIDE INNER GARNISH
4. INSTALL HIGH MOUNTED STOP LIGHT
5. INSTALL THESE PARTS:
(a) Room partition trims
(b) Rear seat
(c) Inner cover trims
(d) LH and RH rear floor finish side plates
(e) Luggage compartment floor mat
6. INSTALL LUGGAGE COMPARTMENT DOOR
(a) Install the door with 4 bolts.
(b) Install clamps.
(c) Connect the connector.
7. INSTALL LUGGAGE COMPARTMENT DOOR TRIM

N21529
BO±56
± BODYSLIDING ROOF (TMC Made)
2404 Author: Date:
5. REMOVE SLIDING ROOF HOUSING
(a) Disconnect the 4 drain hoses from the housing.
(b) Remove the 8 bolts and 4 brackets.
Torque: 5.5 N´m (55 kgf´cm, 49 in.´lbf)
(c) Remove the 6 nuts, then remove the housing as shown
on the following page.

BO0LW±01
H01824
H01825
± BODYSLIDING ROOF (TMMK Made)
BO±65
2413 Author: Date:
REMOVAL
1. REMOVE ROOF HEADLINING
(See page BO±83)
2. REMOVE SIDE GARNISHES
HINT:
At the time of installation, please refer to the following item.
Soak the garnishes in water to soften them before assembly.
3. REMOVE GLASS PANEL ASSEMBLY
(a) Remove the 4 glass panel adjustment screws.
HINT:
At the time of installation, please refer to the following item.
Adjust the height of the glass panel, then tighten the 4 screws.
(b) Pull the glass upward to remove it.
4. REMOVE SLIDING ROOF ASSEMBLY
(a) Remove the 4 drain hoses from the sliding roof assembly.
(b) Remove the 8 bolts and 4 brackets.
Torque: 5.5 N´m (55 kgf´cm, 49 in.´lbf)
(c) Remove the 6 nuts and the sliding roof assembly.

Toyota Supports ASE CertificationPage 1 of 7
BO020-01Title:
SLIDING ROOF DIAGNOSTIC TIPS
Models:
'97 ± '01 TMMK Camry
Technical Service
BULLETIN
August 17, 2001

The 1997 ± 2001 model year TMMK Camry sliding roof assembly components are now
available as service parts. Additional diagnostic and repair information has been
developed to supplement the Repair Manual and to provide service tips for the sliding
roof components.

1997 ± 2001 model year Camry vehicles built in the US (TMMK).
MODEL/PLANTSTARTING VIN
Camry (TMMK)All VINs Begin with ª4º
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty±±±±
REFPART NUMBERPART NAMEQTY
163201±AA010±83Glass Sub±Assy, Sliding Roof1
263202±AA010Rail Sub±Assy, Slide Roof1
363209±AA010Panel Sub±Assy, Roof Wind Deflector1
463214±AA010Channel, Roof Drip, RR1
563217±AA010Garnish, Sliding Roof Side, RH1
663218±AA010Garnish, Sliding Roof Side, LH1
763221±AA010Guide, Roof Channel, RH1
863222±AA010Guide, Roof Channel, LH1
963223±AA010Cable, Sliding Roof Drive, RH1
1063224±AA010Cable, Sliding Roof Drive, LH1
1163225±AA010Spring, Roof Wind Deflector, RH1
1263226±AA010Spring, Roof Wind Deflector, LH1
1363227±AA010Arm, Sliding Roof Lift, RH1
1463228±AA010Arm, Sliding Roof Lift, LH1
1563241±AA010Bracket, Sliding Roof Housing Fr. Mtg., RH2
1663245±AA010Bracket, Sliding Roof Housing Fr. Mtg., LH2
1763251±AA010Weatherstrip, Sliding Roof1
1863260±AA010Gear Assy, Sliding Roof Drive (Not Illustrated)1
BODY
Introduction
Applicable
Vehicles
Warranty
Information
Parts
Information

Toyota Supports ASE CertificationPage 1 of 1
SS003±98Title:
RIVET NUT TOOL
Models:
All Models
Technical Service
BULLETIN
December 11, 1998

Toyota Motor Sales is making available a tool suitable for installing Rivet Nuts as required
by some DIO accessories, such as wind deflectors, roof Racks, and running boards. The
tool is available from Owatonna Tool Company, also known as OTC.
All models requiring Rivet Nuts for the installation of an accessory.
OTC PART NUMBERPART NAMENOTE
00002±95161Rivet Nut ToolMandrels for 5, 6 and 8 mm Rivet Nuts included*
* Also includes a molded plastic carrying case, not shown
Rivet Nut Tool may be ordered by calling the OTC Order Desk at 1±800±933±8335. The
introductory price for this tool is $460.00.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
SPECIAL SERVICE TOOLS
Introduction
Affected
Vehicles
Part Number
Information
Ordering
Procedure
Warranty
Information