TOYOTA LAND CRUISER 1996 J80 Workshop Manual

Engine Coolant
Temperature
Gauge
Ignition Switch
Battery Sender
Gauge
Z06815
Engine
Coolant T emperature Gauge
Ignition
Switch Tester Bulb
(3.4 W)
Battery
BE1222
Oil Pressure Gauge
Ignition
Switch Sender
Gauge
Battery
−
BODY ELECTRICAL COMBINATION METER
BE−37
1996 LAND CRUISER (RM451U)
11. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver
gauge needle indicates COOL.
(c) Ground terminal on the wire harness side connector through a 3.4 W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights up and the receiver gauge needle moves to the hot side.
If operation is as specified, replace the sender gauge. Then re-
check the system.
If operation is not as specified, measure the receiver gauge re-
sistance.
12. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
Between terminalsResistance (Ω )
A − B71 − 79
A − C117 − 141
B − C185 − 215
HINT:
Connect the test leads so that the current from the ohmmeter
can flow according to the above order. This circuit include the
diode.
If resistance value is not as specified, replace the receiver
gauge.
13. INSPECT OIL PRESSURE RECEIVER GAUGE OP-
ERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver
gauge needle indicates LOW.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE4917
Test LED
Battery
BE1217
Warning Light
Ignition
Switch Battery
N01212
BE−38
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
(c) Ground terminal on the wire harness side through a 3.4
W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and that the receiver gauge needle moves to the high
side.
If operation is not as specified, measure the receiver gauge re-
sistance.
14. INSPECT OIL PRESSURE RECEIVER GAUGE RESIS- TANCE
Measure the receiver gauge resistance between terminals. Resistance:
40 − 48 Ω
If resistance value is not as specified, replace the receiver
gauge.
15. INSPECT OIL PRESSURE SENDER GAUGE OPERA-
TION
(a) Disconnect the connector from the sender gauge.
(b) Apply battery positive voltage to the sender gauge termi- nal through a test LED.
(c) Check that the bulb does not light when the engine is stopped.
(d) Check that the LED flashes when the engine is running. The number of flashed should vary with engine speed.
If operation is not as specified, replace the sender gauge.
16. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connectors from the level warning switch and parking brake switch.
(b) Connect terminals on the wire harness side connector of
the level warning switch connector.
(c) Turn the ignition switch ON, and check that the warning light lights up.
17. INSPECT PARKING BRAKE SWITCH
(a) Check that there is continuity between terminal and the switch set nut with switch pin released (parking brake le-
ver pulled up).
(b) Check that there is no continuity between terminal and the switch set nut with switch pin pushed in. (parking
brake lever released)
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE2570
ON
OFF
BE0044
BE1428
−
BODY ELECTRICAL COMBINATION METER
BE−39
1996 LAND CRUISER (RM451U)
18. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
(a) Check that there is no continuity between terminals with
the switch OFF (float up).
(b) Check that there is continuity between terminals with the switch ON (float down).
If operation is not as specified, replace the switch.
19. INSPECT OPEN DOOR WARNING LIGHT
(a) Disconnect the connector from the door courtesy switch and ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON, and check that the warning light lights up.
If the warning light does not light up, test the bulb.
20. INSPECT DOOR COURTESY SWITCH
(a) Check that there is continuity between terminal and the
switch body with the switch ON (switch pin re-
leased:opened door).
(b) Check that there is no continuity between terminal and
the switch body with the switch OFF (switch pin pushed
in:closed door).
If operation is not as specified, replace the switch.
21. INSPECT SEAT BELT WARNING LIGHT
(a) Disconnect the connector from the seat belt warning relay.
(b) Ground terminal 9 on the wire harness side connector.
(c) Turn the ignition switch ON, and check that the warning
light lights up.
If the warning light does not light up, test the bulb.
22. INSPECT SEAT BELT BUCKLE SWITCH CONTINUITY
(a) Check that there is continuity between terminals with the switch ON (belt unfastened).
(b) Check that there is no continuity between terminals with the switch OFF (belt fastened).
If operation is not as specified, replace the seat belt inner.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−40
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
23. INSPECT SEAT BELT WARNING RELAY CIRCUIT
Disconnect the connector from the relay and inspect the con-
nector on the wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
1 − GroundConstantContinuity
4 − GroundDriver’s seat belt position UNFASTENContinuity
4 − GroundDriver’s seat belt position FASTENNo continuity
7 − GroundIgnition key SETContinuity
7 − GroundIgnition key RemoveNo continuity
8 − GroundDriver’s door position OPENContinuity
8 − GroundDriver’s door position CLOSENo continuity
5 − GroundIgnition switch position ONBattery positive voltage
5 − GroundIgnition switch position LOCK or ACCNo voltage
9 − GroundConstantBattery positive voltage
If circuit is as specified, try another relay.
If the circuit is not as specified, check the circuits connected to
other parts.
24. INSPECT ENGINE OIL LEVEL WARNING SWITCH
(a) Check that there is continuity between terminal with the
switch each position.
(b) Heat the switch to above 60° C (140°F) in an oil bath.
(c) Check that there is continuity between terminals with the switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06300
BrightDark 2
3
Extinguished
1
−
BODY ELECTRICAL COMBINATION METER
BE−41
1996 LAND CRUISER (RM451U)
25. INSPECT ENGINE OIL LEVEL WARNING CIRCUIT
Disconnect the switch connector and inspect the connector on
wire harness side, as shown.
Tester connectionConditionSpecified condition
2 − GroundConstantContinuity
If continuity is not as specified, inspect the wire harness or
ground point.
26. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Ground terminal 1 on the wire harness connector.
(c) Turn the ignition switch ON, and check that the warning
light lights up approximately 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.
27. INSPECT LIGHT CONTROL RHEOSTAT
(a) Connect terminals 1 and 3 through a 3.4 W test bulb.
(b) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 2.
(c) Turn the rheostat knob to fully counterclockwise, and
check that the test bulb goes out.
(d) Gradually turn the rheostat knob to clockwise, and check
that the test bulb brightness changes from dark to bright.
If operation is not as specified, replace the rheostat.
HINT:
Adjust the brightness of illumination lights by rheostat.
A/C Control Assembly
Antenna Switch
Ash Receptacle
Audio
Center Diff. Lock Switch
Cigarette Lighter
Defogger Switch
Hazard Warning Switch
Shift Lever
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1ME−01
BE−42
−
BODY ELECTRICAL DEFOGGER SYSTEM
1180
Author: Date:
1996 LAND CRUISER (RM451U)
DEFOGGER SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MF−01
BE4029
Tester PlobeTin FoilHeat Wire
BE0123
At Center
BE0124
0 V
Several
Broken
Wire
−
BODY ELECTRICAL DEFOGGER SYSTEM
BE−43
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT DEFOGGER SWITCH CONTINUITY
ConditionTester connectionSpecified condition
Switch OFF−No continuity
Switch ON2 − 3 − 6Continuity
Illumination circuit1 − 4Continuity
If continuity is not as specified, check the bulb or replace the
switch.
2. INSPECT DEFOGGER RELAY CONTINUITY (See page
BE−46 .)
3. INSPECT DEFOGGER WIRES
NOTICE:
When cleaning the glass, use a soft, dry cloth and wipe the
glass in the direction of the wire. Take care not to damage
the wires.Do not use detergents or glass cleaners with
abrasive ingredients.When measuring voltage, wind a
piece of tin foil around the top of the negative ( −) probe and
press the foil against the wire with your finger, as shown.
(a) Turn the ignition switch ON.
(b) Turn the defogger switch ON.
(c) Inspect the voltage at the center of each heat wire, as shown.
VoltageCriteria
Approx. 5VOkay (No break in wire)
Approx.10V or 0VBroken wire
HINT:
If there is 10 V, the wire is broken between the center of the wire
and positive (+) end. If there is no voltage, the wire is broken
between the center of the wire and ground.
(d) Place the voltmeter positive (+) lead against the defogger
positive (+) terminal.
(e) Place the voltmeter negative ( −) lead with the foil strip
against the heat wire at the positive (+) terminal end and
slide it toward the negative ( −) terminal end.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE0150
Repair PointBroken
Wire
Marking Tape
BE0151
BE−44
−
BODY ELECTRICAL DEFOGGER SYSTEM
1996 LAND CRUISER (RM451U)
(f) The point where the voltmeter deflects from zero to sever-
al V is the place where the heat wire is broken.
HINT:
If the heat wire is not broken, the voltmeter indicates 0 V at the
positive (+) end of the heat wire but gradually increases to about
12 V as the meter probe is moved to the other end.
4. IF NECESSARY, REPAIR DEFOGGER WIRE
(a) Clean the broken wire tips with a grease, wax and silicone
remover.
(b) Place the masking tape along both sides of the wire to be
repaired.
(c) Thoroughly mix the repair agent (Dupont paste No. 4817
or equivalent).
(d) Using a fine tip brush, apply a small amount to the wire.
(e) After a few minutes, remove the masking tape.
(f) Do not repair the defogger wire for at least 24 hours.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MG−01
−
BODY ELECTRICAL POWER WINDOW CONTROL SYSTEM
BE−45
1183
Author: Date:
1996 LAND CRUISER (RM451U)
POWER WINDOW CONTROL SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06846
BE1MH−01
BE−46
−
BODY ELECTRICAL POWER WINDOW CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT POWER WINDOW MASTER SWITCH CON- TINUITY
Front Driver’s Switch (Window unlock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 13
6 − 7 − 8Continuity
OFF1 − 2 − 6 − 13Continuity
DOWN1 − 2 − 6
7 − 8 − 13Continuity
Front Driver’s Switch (Window lock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 13
6 − 7 − 8Continuity
OFF1 − 2 − 6 − 13Continuity
DOWN1 − 2 − 6
7 − 8 − 13Continuity
Front Passenger’s Switch (Window unlock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 5
7 − 8 − 12Continuity
OFF1 − 2 − 5 − 12Continuity
DOWN1 − 2 − 12
5 − 7 − 8Continuity
Front Passenger’s Switch (Window lock):
Switch positionTester connectionSpecified condition
UP7 − 8 − 12Continuity
OFF5 − 12Continuity
DOWN5 − 7 − 8Continuity
Rear Left Switch (Window unlock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 9
7 − 8 − 10Continuity
OFF1 − 2 − 9 − 10Continuity
DOWN1 − 2 − 10
7 − 8 − 9Continuity
Rear Left Switch (Window lock):
Switch positionTester connectionSpecified condition
UP7 − 8 − 10Continuity
OFF9 − 10Continuity
DOWN7 − 8 − 9Continuity
Rear Right Switch (Window unlock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 14
7 − 8 − 11Continuity
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010