TOYOTA LAND CRUISER 1996 J80 Workshop Manual

−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
BE−17
1996 LAND CRUISER (RM451U)
(c) Adjust headlight in horizontal alignment.
If the ”0” moves away from the mark beyond the acceptable
range, adjust the ”0” back to the mark using adjusting screw B.
HINT:
The beam angle will change about 0 °23’ with one mark.
2. REPLACING HEADLIGHT
(a) Replace the headlight.
(b) Inspect the headlight aim. Do the following before inspec-
tion.
Make sure the body around the headlight is not de-
formed.
Park the vehicle on a level spot.
The driver gets into the driver’s seat and puts the
vehicle in a state ready for driving (with a full tank).
Bounce the vehicle several times.
(c) Adjust headlight in vertical alignment (1) Using adjusting screw A, adjust the headlight aim to
within the specifications.
HINT:
The beam angle will change about 0 °11’ with one mark.
(2) Make sure the gauge bubble is within the accept- able range.
HINT:
If the gauge bubble is outside the acceptable range, check that
the vehicle is parked on a level place.
(d) Readjust the headlight aim after parking the vehicle on a level place.
(e) Adjust the headlight in horizontal alignment. (1) Using adjusting screw B, adjust the headlight aim to
within the specifications.
HINT:
The beam angle will change about 0 °23’ with one mark.
(2) Using adjusting nut C, adjust the ”0” back to the mark.
HINT:
For adjustment, pull nut C to the rear of the vehicle to free it. Af-
ter adjustment, check that the nut C is locked in.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M1−01
BE−18
−
BODY ELECTRICAL TURN SIGNAL AND HAZARD WARNING SYSTEM
1156
Author: Date:
1996 LAND CRUISER (RM451U)
TURN SIGNAL AND HAZARD WARNING SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE27G−01
BE1843
−
BODY ELECTRICAL TURN SIGNAL AND HAZARD WARNING SYSTEM
BE−19
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT HAZARD WARNING SWITCH CONTINUITY
ConditionTester connectionSpecified condition
Switch OFF7 − 10Continuity
Switch ON7 − 8
4 − 5 − 6 − 9Continuity
Illumination circuit2 − 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative ( −) lead to terminal 3.
(b) Connect the 2 turn signal light bulbs parallel to each other
to terminals 1 and 3, and check that the bulbs flash.
HINT:
The turn signal lights should flash 60 to 120 times per minute.
If one of the front or rear turn signal lights has an open circuit,
the number of flashes will be more than 140 per minute.
If operation is not as specified, replace the flasher.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M3−01
BE−20
−
BODY ELECTRICAL INTERIOR LIGHT SYSTEM
1158
Author: Date:
1996 LAND CRUISER (RM451U)
INTERIOR LIGHT SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M4−01
BE1428
ON
OFF
−
BODY ELECTRICAL INTERIOR LIGHT SYSTEM
BE−21
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT GLOVE BOX LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF (Closed)−No continuity
ON (Opened)1 − 2Continuity
If continuity is not as specified, replace the switch.
2. INSPECT DOOR COURTESY SWITCH CONTINUITY
(a) Check that there is continuity between terminal and the
switch body with the switch ON (switch pin released:
opened door).
(b) Check that there is no continuity between terminal and the switch body with the switch OFF (switch pin pushed
in: closed door).
If operation is not as specified, replace the switch.
3. INSPECT FRONT PERSONAL LIGHT CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
ON5 − 6Continuity
If continuity is not as specified, replace the personal light.
4. INSPECT ROOM LIGHT ASSEMBLY
(a) Disconnect the connector from room light assembly.
(b) Turn the room light switch ON, check that there is continu-
ity between terminal 2 and body ground.
(c) Turn the room light switch DOOR, and check that there is continuity between terminal 1 and 2.
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M5−01
BE−22
−
BODY ELECTRICAL BACK−UP LIGHT SYSTEM
1160
Author: Date:
1996 LAND CRUISER (RM451U)
BACK −UP LIGHT SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M6−01
−
BODY ELECTRICAL BACK−UP LIGHT SYSTEM
BE−23
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT PARK/NEUTRAL POSITION SWITCH CONTINUITY (See page AT−6)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M7−01
BE−24
−
BODY ELECTRICAL STOP LIGHT SYSTEM
1162
Author: Date:
1996 LAND CRUISER (RM451U)
STOP LIGHT SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M8−01
−
BODY ELECTRICAL STOP LIGHT SYSTEM
BE−25
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT STOP LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
SW pin free1 − 2Continuity
SW pin pushed in−No continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M9−01
BE−26
−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
1164
Author: Date:
1996 LAND CRUISER (RM451U)
WIPER AND WASHER SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010