TOYOTA LAND CRUISER 1996 J80 Workshop Manual

AB0119I00053 I00031
ON
IDL
(−) (+)
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−317
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check voltage between terminal IDL of cruise control ECU connector and body
ground.
PREPARATION:
(a) Remove the ECU with connector still connected.
(b) Disconnect the ECM and ABS ECU connectors.
(c) Turn ignition switch ON.
CHECK:
Measure voltage between terminal IDL of ECU connector and
body ground when the throttle valve is fully closed and fully
opened.
OK:
Throttle valve positionVoltage
Fully opened10 − 14 V
Fully closedBelow 2 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI−295 ).
NG
2 Check harness and connector between ECM and throttle position sensor (See page IN−28 ).
NG Repair or replace harness or connector.
OK
3 Check throttle position sensor circuit (See page DI−35).
NG Replace throttle position sensor.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00052
Throttle Position Sensor
3
4
DI−318
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
4 Check throttle position sensor.
PREPARATION:
Disconnect the throttle position sensor connector.
CHECK:
Measure resistance between terminals 3 and 4 of throttle posi-
tion sensor connector when the throttle valve is fully closed and
fully opened.
OK:
Throttle valve positionResistance
Fully opened1 MΩ or higher
Fully closedBelow 2.3 kΩ
NG Replace throttle position sensor.
OK
5 Check for open and short in harness and connector between cruise control\
ECU and throttle position sensor, throttle position sensor and body ground
(See page IN−28 ).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00494
Cruise Control ECUECT
22 9
15
9
E4S2
R−Y
ECM
E7
OD1
ODC17
18
G−R
G−O
C17
R−Y
R−Y
2 EC2 IH2
Ellectronically Con trolled
Transmission Solenoid
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−319
1996 LAND CRUISER (RM451U)
Electronically Controlled Transmission Communication Circuit
CIRCUIT DESCRIPTION
When driving uphill under cruise control, in order to reduce shifting due to ON− OFF overdrive operation and
to provide smooth driving, when down shifting in the electronically controlled transmission occurs, a si\
gnal
to prevent upshift until the end of the up hill slope is sent from the cru\
ise control ECU to the electronically
controlled transmission.
Terminal ECT of the cruise control ECU detects the shift change signal (\
output to electronically controlled
transmission No. 2 solenoid) from the ECM.
If vehicle speed down, also when terminal ECT of the cruise control ECU receives down shifting signal, it
sends a signal from terminal OD to ECM to cut overdrive until the end of the uph\
ill slope, and the gear shifts
are reduced and gear shift points in the electronically controlled transmis\
sion are changed.
WIRING DIAGRAM
DI5OK−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0119I00012 I00025
ON
OD
(−) (+)
DI−320
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check operation of overdrive.
PREPARATION:
Test drive after engine warms up.
CHECK:
Check that overdrive ON ↔ OFF occurs with operation of OD switch ON−OFF.
NG Check and repair electronically controlledtransmission (See page DI−129 ).
OK
2 Check voltage between terminal OD of harness side connector of cruise co\
ntrol ECU and body ground.
PREPARATION:
(a) Remove the ECU with connector still connected.
(b) Turn ignition switch ON.
(c) Disconnect the ECU connector.
CHECK:
Measure voltage between terminal OD of harness side connec-
tor of ECU and body ground.
OK:
Voltage: 10 − 14 V
NG Go to step 5.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00019
ECT
(−) (+)
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−321
1996 LAND CRUISER (RM451U)
3 Check voltage between terminal ECT of cruise control ECU connector and body
ground (On test drive).
PREPARATION:
(a) Connect the ECU connector.
(b) Test drive after engine warms up.
CHECK:
Check voltage between terminal ECT of ECU connector and
body ground when OD switch is ON and OFF.
OK:
OD switch positionVoltage
ON8 − 14 V
OFFBelow 0.5 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI−295 ).
NG
4 Check harness and connector between terminal ECT of cruise control ECU a\
nd electronically controlled transmission solenoid (See page IN−28).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU.
5 Check harness and connector between terminal OD of cruise control ECU an\
d terminal OD1 of ECM (See page IN−28 ).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU (See
page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00495
Cruise Control ECUD
2
Y Y
B
B 4
Instrument Panel Fuse Block B−O
IH1
1 3
6
B−O
GAUGE
9
2 4
Ignition Switch C17
B−Y FL AM1 AM1
EA2 2
1
B
B 6
Battery 2
1 W
2 2
B−L
A/T Indicator Light
(Park/Neutral Position Switch)
IH24
P1
P1
F11 F11 J4
JUNCTION
CONNECTOR
I12 I12 Fusible Link
F6 2
D
Fusible Link
Y
DI−322
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Park/Neutral Position Switch Circuit
CIRCUIT DESCRIPTION
When the shift position is put in except D position, a signal is sent from t\
he park/neutral position switch to
the ECU. When this signal is input during cruise control driving, the EC\
U cancels the cruise control.
WIRING DIAGRAM
DI5OL−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Input SignalIndicator Light
Blinking Pattern
Turn PNP switch
OFF (Shift to
except D position)
LightON
OFF SW ON
SW OFF
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−323
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check starter operation.
CHECK:
Check that the starter operates normally and that the engine starts.
NG Proceed to engine troubleshooting (See page DI−1).
OK
2 Input signal check.
PREPARATION:
See input signal check on page DI−286.
CHECK:
Check the indicator light when shifting into except D position.
OK:
The indicator light goes off when shifting into except
D position.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0119I00017 I00026
ON
D
(−)
(+)
DI−324
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
3 Check voltage between terminal D of cruise control ECU connector and body
ground.
PREPARATION:
Turn ignition switch ON.
CHECK:
Measure voltage between terminal D of ECU connector and
body ground when shifting into D position and other positions.
OK:
Shift PositionVoltage
D position10 − 14 V
Other positionsBelow 1 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI−295 ).
NG
4 Check harness and connector between cruise control ECU and park/neutral position switch (See page IN−28).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU (See
page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00496
Cruise Control ECU
Fusible Link Fusible Link
Battery BR
BR
Instrument
Panel Fuse Block
ECU−IG
Ignition Switch BB
2
4 3
2
F6
1 JUNCTION
CONNECTOR J6
C17
C17B−W
I12
I12 4
2
2
2
2 B−W
F11
F11
B
B−Y
B
6EA2B
GND
13
14
AM1
FL AM1
1
ID
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−325
1996 LAND CRUISER (RM451U)
ECU Power Source Circuit
CIRCUIT DESCRIPTION
The ECU power source supplies power to the actuator and sensors, etc.. When\
terminal GND and the cruise
control ECU case are grounded.
WIRING DIAGRAM
DI5OM−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N18670
Junction Block No.1ECU−B
Fuse
AB0119I00014 I00027
GNDB
ON
(−)
(+)
DI−326
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check ECU −B fuse.
PREPARATION:
Remove the ECU −B fuse from instrument panel fuse block.
CHECK:
Check continuity of ECU −B fuse.
OK:
Continuity
NG Check for short in all the harness and compo- nents connected to ECU−B fuse.
OK
2 Check voltage between terminals B and GND of cruise control ECU connecto\
r.
PREPARATION:
(a) Remove the ECU with connector still connected.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals B and GND of ECU con-
nector.
OK:
10 − 14 V
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010