automatic transmission fluid TOYOTA LAND CRUISER 1996 J80 Workshop Manual

IN04Q−07
−
INTRODUCTION TERMS
IN−33
33
Author: Date:
1996 LAND CRUISER (RM451U)
TERMS
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti−Lock Brake System
ACAlternating Current
ACCAccessory
ACISAcoustic Control Induction System
ACSDAutomatic Cold Start Device
A.D.D.Automatic Disconnecting Differential
A/FAir−Fuel Ratio
AHCActive Height Control Suspension
ALRAutomatic Locking Retractor
ALTAlternator
AMPAmplifier
ANTAntenna
APPROX.Approximately
A/TAutomatic Transmission (Transaxle)
AT FAutomatic Transmission Fluid
AUTOAutomatic
AUXAuxiliary
AV GAverage
AV SAdaptive Variable Suspension
BABrake Assist
BACSBoost Altitude Compensation System
BATBattery
BDCBottom Dead Center
B/LBi−Level
B/SBore−Stroke Ratio
BTDCBefore Top Dead Center
BVSVBimetallic Vacuum Switching V alve
Calif.California
CBCircuit Breaker
CCoCatalytic Converter For Oxidation
CDCompact Disc
CFCornering Force
CGCenter Of Gravity
CHChannel
COMB.Combination
CPECoupe
CPSCombustion Pressure Sensor
CPUCentral Processing Unit
CRSChild Restraint System
CTRCenter
C/VCheck Valve
CVControl Valve
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07274
AT0T4−01
AT3168
SST
AT1362
Seal Breadth
2 − 3 mm
−
AUTOMATIC TRANSMISSION VALVE BODY ASSEMBLY
AT−7
791
Author: Date:
1996 LAND CRUISER (RM451U)
VALVE BODY ASSEMBLY
ON−VEHICLE REPAIR
1. DRAIN ATF
Torque: 20 N·m (205 kgf·cm, 15 ft·lbf)
2. REMOVE OIL PAN
NOTICE:
Some fluid will remain in the oil pan.
(a) Remove the 19 bolts. Torque: 7.4 N·m (75 kgf·cm, 65 in.·lbf)
(b) Install the blade of SST between the transmission case and oil pan, cut off applied sealer and then remove the oil
pan.
SST 09032−00100
NOTICE:
When removing the oil pan, be careful not to damage the oil
pan flange.
HINT:
At the time of installation, after removing all the old FIPG on the
contacting surface of the oil pan and transmission case, apply
new FIPG to the oil pan.(See page AT −1)
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
3. WHEN REPLACING 3 SHIFT SOLENOID VALVES
(a) Disconnect the connectors from the solenoid valves.
(b) Remove the 3 solenoid valve mounting bolts. Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
(c) Remove the 3 solenoid valves.
HINT:
At the time of installation, replace the O−rings with new ones.
4. REMOVE OIL STRAINER
Remove the 4 bolts, and the oil strainer and gaskets. Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
NOTICE:
Be careful as some fluid will c ome out with the oil strainer.
Bolt length:
Bolt A: 16 mm (0.63 in.)
Bolt B: 20 mm (0.79 in.)
Bolt C: 28 mm (1.10 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
AUTOMATIC TRANSMISSION VALVE BODY ASSEMBLY
AT−9
793
Author: Date:
1996 LAND CRUISER (RM451U)
8. REINSTALL VALVE BODY ASSEMBLY
To install, follow the removal procedure in reverse.
HINT:
After installation, fill ATF and check the fluid level. (See page
DI−131)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0T6−01
AT6684
Q05731
200 mm
(7.87 in.)
0.8 − 1.5 mm
(0.031 − 0.059 in.)
−
AUTOMATIC TRANSMISSION THROTTLE CABLE
AT−11
795
Author: Date:
1996 LAND CRUISER (RM451U)
THROTTLE CABLE
ON−VEHICLE REPAIR
1. DISCONNECT THROTTLE CABLE
(a) Disconnect the cable from the throttle linkage.
(b) Disconnect the cable from the cable clamps in the engine
compartment.
(c) Remove the bolt and disconnect the cable clamp from the
torque converter clutch housing.
2. REMOVE VALVE BODY (See page AT −7)
3. REMOVE THROTTLE CABLE
Remove the retaining bolt and pull out the throttle cable.
4. REINSTALL THROTTLE CABLE
(a) To install, follow the removal procedure in reverse.
HINT:
If throttle cable is new, stake the stopper on the inner cable.
(b) Bend the cable so there is a radius of about 200 mm (7.87
in.)
(c) Pull the inner cable lightly until slight resistance is felt, and
hold it there.
(d) Stake the stopper, 0.8− 1.5 mm (0.031−0.059 in.) from the
end of outer cable.
After installation, fill ATF and check the fluid level
(See page DI−131 ).
Adjust the throttle cable (See page DI−131).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0TA−01
−
AUTOMATIC TRANSMISSION AIR COOLED OIL COOLER
AT−17
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page AT −16).
HINT:
After installation, check fluid level (See page DI−131).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0TD−01
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−25
1996 LAND CRUISER (RM451U)
INSTALLATION
1. CHECK TORQUE CONVERTER CLUTCH INSTALLA-
TION
Using calipers and a straight edge, measure from the installed
surface of the transmission housing. Correct distance: More than 15.7 mm (0.618 in.)
2. INSTALL TRANSMISSION
Installation is in the reverse order of removal (See page
AT −20 ).
HINT:
After installation, adjust the shift lever position and throttle
cable (See page DI−131).
Fill and check fluid level (See page DI−131).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO118−01
CO−16
−
COOLING RADIATOR
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL RADIATOR
(a) Install the 2 radiator brackets with the 4 nuts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Install the radiator with the 2 bolts and 2 nuts. Torque:
Bolt: 18 N·m (185 kgf·cm, 13 ft·lbf)
Nut: 12 N·m (120 kgf·cm, 9 ft·lbf)
2. CONNECT A/T OIL COOLER HOSES
3. CONNECT RADIATOR OUTLET HOSE
4. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(b) Temporarily install the fan pulley mounting nuts.
(c) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(d) Connect the oil cooler hose to the clamp on the fan
shroud.
(e) Install the drive belts with the adjusting bolt and pivot bolt.
(f) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(g) Adjust the drive belts (See page CH−2 ).
5. CONNECT RADIATOR RESERVOIR HOSE
6. CONNECT RADIATOR INLET HOSE
7. CONNECT NO.3 WATER BYPASS HOSE
8. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
9. INSTALL BATTERY AND BATTERY TRAY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery with the hold−down clamp and nuts.
(d) Connect the battery cables.
10. FILL RADIATOR WITH ENGINE COOLANT
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT3417
OK if hot
Add if hot
Q07273
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−137
1996 LAND CRUISER (RM451U)
(e) P position test.
Stop the vehicle on a grade (more than 5 °) and after shifting into the P position, release the parking
brake. Then, check to see that the parking lock pawl holds the vehicle i\
n place.
6. BASIC INSPECTION
(a) Check the fluid level.
HINT:
Drive the vehicle so that the engine and transmission are
at normal operating temperature.
Fluid temp.: 70 − 80°C (158 − 176° F)
Only use the COOL range on the dipstick as a rough refer-
ence when the ATF is replaced or the engine does not
run.
(1) Park the vehicle on a level surface and set the park-
ing brake.
(2) With the engine idling and the brake pedal de- pressed, shift the shift lever into all positions from P
to L position and return to P position.
(3) Pull out the dipstick and wipe it clean.
(4) Push it back fully into the pipe.
(5) Pull it out and check that the fluid level is in the HOT range.
If the level is at the low side, add new fluid. Fluid type: ATF DEXRON ®II
NOTICE:
Do not overfill.
(b) Check the fluid condition. If the fluid smells burnt or is black, replace it.
(c) Replace the ATF. (1) Remove the drain plug and drain the ATF.
(2) Reinstall the drain plug securely.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07308
AT3417
OK if hot
Add if hot
AT4252
0 − 1 mm
Q07309
DI−138
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(3) With the engine OFF, add new fluid through the oil
filler pipe.
Fluid type: ATF DEXRON ®II
Capacity:
Dry fill: 11.0 liters (11.6 US qts, 9.7 Imp. qts)
Drain and refill: 1.9 liters (2.0 US qts, 1.7 Imp. qts)
(4) Start the engine and shift the shift lever into all posi-
tions from P to L position and then shift into P posi-
tion.
(5) With the engine idling, check the fluid level. Add fluid up to the COOL level on the dipstick.
(6) Check the fluid level at the normal operating tem- perature 70 − 80° C (158 − 176°F) and add as nec-
essary.
NOTICE:
Do not overfill.
(d) Check the fluid leaks.
Check for leaks in the transmission.
If there are leaks, it is necessary to repair or replace O −rings,
Seal packings, oil seals, plugs or other parts.
(e) Inspect and adjust the throttle cable. (1) Check that the throttle valve is fully closed.
(2) Check that the inner cable is not slack.
(3) Measure the distance between the outer cable endand stopper on the cable.
Standard distance: 0 − 1 mm (0 − 0.04 in.)
If the distance is not standard, adjust the cable by the adjusting
nuts.
(f) Inspect and adjust the shift lever position. When shifting the shift lever from the N position to other
positions, check that the lever can be shifted smoothly
and accurately to each position and that the position indi-
cator correctly indicates the position.
If the indicator is not aligned with the correct position, carry out
the following adjustment procedures. (1) Loosen the nut on the control rod.
(2) Push the control rod fully rearward.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−140
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(6) Shift into the D position. Press all the way down on the accelerator pedal wi\
th your right foot.
Quickly read the stall speed at this time.
Stall speed: 1,950 ± 150 rpm
(7) Do the same test in R position.
Stall speed: 1,950 ± 150 rpm
Evaluation:
ProblemPossible cause
Stall speed low in D and R positions
 Engine output may be insuf ficient
 Stator one− way clutch is operating properly
HINT:
If more than 600 rpm below the specified value, the torque con-
verter clutch could be faulty.
Stall speed high in D position
 Line pressure too low
 Forward clutch slipping
 No. 2 one− way clutch not operating properly
 O/D one− way clutch not operating properly
Stall speed high in R position
Line pressure too low
 Direct clutch slipping
 1st and reverse brake slipping
 O/D clutch slipping
Stall speed high in D and R positions
Line pressure too low
 Improper fluid level
 O/D one− way clutch not operating properly
(b) Measure the time lag.
When the shift lever is shifted while the engine is idling, there will be a certain time lapse o\
r lag before
the shock can be felt. This is used for checking the condition of the O/D d\
irect clutch, forward clutch,
direct clutch and 1st and reverse brake.
NOTICE:
Do the test at normal operating ATF temperature 50 − 80°C (122 − 176° F).
Be sure to allow 1 minute interval between tests.
Take 3 measurements and take the average value.
(1) Fully apply the parking brake.
(2) Start the engine and check idle speed.
Idle speed: 650 ± 50 rpm (In N position and air conditioner OFF)
(3) Shift the shift lever from N to D position. Using a stop watch, measure the ti\
me it takes from shift-
ing the lever until the shock is felt.
In the same manner, measure the time lag for N → R.
Time lag: N → D Less than 1.2 seconds
In the same way, measure the time lag for N → R.
Time lag: N → R Less than 1.5 seconds
If N → D time or N → R time lag is longer than specified:
Evaluation:
ProblemPossible cause
N → D time lag is longer
Line pressure too low
 Forward clutch worn
 O/D one− way clutch not operating properly
N → R time lag is longer
Line pressure too low
 Direct clutch worn
 1st and reverse brake worn
 O/D one− way clutch not operating properly
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010