TOYOTA LAND CRUISER 1998 Factory Repair Manual

SA157-02
F04353
SST
SST
F04354
SST
F05253
SST
F05254
SST
- SUSPENSION AND AXLEFRONT LOWER SUSPENSION ARM
SA-77
2027 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
1. REPLACE NO. 1 BUSHING
(a) Using a chisel and hammer, pry up the flange of the No.
1 bushing.
(b) Using SST, remove the No. 1 bushing.
SST 09710-30021 (09710-03101),
09950-00020, 09950-00030,
09950-4001 1 (09957-04010)
(c) Using SST and a press, install a new No. 1 bushing.
SST 09726-36010
2. REPLACE NO. 2 BUSHING
(a) Using SST, remove the No. 2 bushing.
SST 09710-22021 (09710-01071),
09726-3501 1 (09726-05021),
09830-36010
(b) Using SST, install a new No. 2 bushing.
SST 09631-32020, 09830-36010

F04355
SA-78
- SUSPENSION AND AXLEFRONT LOWER SUSPENSION ARM
2028 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3. REPLACE DUST COVER
(a) Remove the wire and dust cover.
(b) Coat the ball joint with grease in the boot kit.
(c) Install a new dust cover and wire.

SA14R-02
F05252
Non-reusable part
N´m (kgf´cm, ft´lbf) : Specified torque

Cushion
Shock Absorber
68 (700, 50)
135 (1,400, 100)
Cushion
Retainer Front Fender Apron
Retainer SA-60
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
2010 Author
: Date
:
2004 LAND CRUISER (RM1071U)
FRONT SHOCK ABSORBER
COMPONENTS

SA14U-03
F05250
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
SA-63
2013 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DISPOSAL
DISCARD SHOCK ABSORBER
Before discarding the shock absorber, drill a hole of 2 - 3 mm
(0.079 - 0.118 in.) in diameter at the location shown in the il-
lustration to discharge the gas inside.
NOTICE:

When drilling, chips may fly out, work carefully.

The gas is colorless, odorless and non-poisonous.

SA14T-02
SA0627
SA-62
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
2012 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
INSPECT SHOCK ABSORBER
Compress and extend the shock absorber rod and check that
there is no abnormal resistance or unusual operation sounds.
If there is any abnormality, replace the shock absorber with a
new one.
NOTICE:
When disposing the shock absorber, see DISPOSAL on
page SA-63.

SA14V-01
SA-64
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
2014 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse order of removal (See page SA-61).

SA14S-02
F04382
F04407
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
SA-61
2011 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 131 N´m (1,340 kgf´cm, 97 ft´lbf)
2. REMOVE FRONT FENDER APRON
3. REMOVE SHOCK ABSORBER
(a) Remove the bolt, nut and disconnect the shock absorber
from the lower suspension arm.
Torque: 135 N´m (1,400 kgf´cm, 100 ft´lbf)
(b) While holding the piston rod, remove the nut, cushion, re-
tainer and shock absorber.
Torque: 68 N´m (700 kgf´cm, 50 ft´lbf)
(c) Remove the cushion and retainer from the shock absorb-
er.

SA159-02
F05236
Stabilizer Bar
25 (250, 18)
Retainer
Cushion
Cushion
Bracket
18 (185, 13)
Cushion
Retainer
52 (530, 38)
Stabilizer Bar Link
Engine Under Cover
N´m (kgf´cm, ft´lbf) : Specified torque


Non-reusable part
18 (185, 13)


SA-80
- SUSPENSION AND AXLEFRONT STABILIZER BAR
2030 Author
: Date
:
2004 LAND CRUISER (RM1071U)
FRONT STABILIZER BAR
COMPONENTS

SA15B-01
SA-82
- SUSPENSION AND AXLEFRONT STABILIZER BAR
2032 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse order of removal (See page SA-81).

SA15A-02
F05117
F04402
- SUSPENSION AND AXLEFRONT STABILIZER BAR
SA-81
2031 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ENGINE UNDER COVER
2. REMOVE LH AND RH STABILIZER BAR LINKS
(a) Remove the nut, bolt, 2 retainers, 2 cushions and stabiliz-
er bar link.
Torque:
Bolt: 52 N´m (530 kgf´cm, 38 ft´lbf)
Nut: 25 N´m (250 kgf´cm, 18 ft´lbf)
(b) Employ the same manner described above to the other
side.
3. REMOVE STABILIZER BAR
(a) Remove the 4 bolts, 2 brackets and 2 cushions.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
(b) Remove the stabilizer bar.