TOYOTA PRIUS 2007 2.G Owners Manual

261
26P197
Turn this knob to select the next or
previous channel.
If you turn continuously, you can rapidly
scroll forward or down through the chan-
nels.
26p213b
(d) Presetting a channel1. Tune in the desired channel.
2. Touch one of the channel selector switches (16) and hold it until a
beep is heard. This sets the chan-
nel to the switch and the frequency
appears on the switch.
Each switch can store three SAT chan-
nels. To change the preset channel to a
different one, follow the same procedure.
The preset channel memory is cancelled
when the power source is interrupted by
battery disconnection or a blown fuse. (e) Selecting a channel
Tune in the desired channel using one of
the following methods.
Preset tuning:
Touch the switch (1 −6) for
the channel you want. The switch (1 −6) is
highlighted in green.
Manual tuning within the channel cate-
gory: Turn the “TUNE·FILE” knob. The
radio will step up or down the channel.
Manual tuning within the current chan-
nel category: Push the “SEEK·TRACK”
button on either side. The radio will step
up or down the channel within the current
channel category. Touch the “TYPE SEEK”
switch. The radio will step up the channel
within the current channel category.

262
To scan the currently selected channel
category: Touch the “TYPE SCAN” switch
or push the “SCAN” button briefly.
“SCAN” appears on the display. The ra-
dio will find the next channel in the same
channel category, stay there for a few
seconds, and then scan again. To select
a channel, touch the “TYPE SCAN” switch
or push the “SCAN” button a second time. To scan the preset channels:
Push the
“SCAN” button and hold it until you hear
a beep. “P.SCAN” appears on the display.
The radio will find the next preset chan-
nel, stay there for a few seconds, and
then move to the next preset channel. To
select a channel, push the “SCAN” button
a second time.(f) Channel category
Touch either “TYPE
” or “TYPE ”
switch to switch to the next or previous
category.

263
26p216c
(g) Displaying the title and name
When you touch the “TEXT” switch, the
song/program title and the artist name/fea-
ture are displayed.
Up to 32 alphanumeric characters can be
displayed. (Some information will not be
fully displayed.)

264
(h) If the satellite radio tuner malfunctions
When problems occur with the XM tuner, a message will appear on the display. Referring to the table below to identify the problem,
take the suggested corrective action.
ANTENNAThe XM  antenna is not connected. Check whether the XM antenna cable is attached securely.
A short−circuit occurs in the antenna or the surrounding antenna cable. See a T\
oyota certified dealer.
UPDATING
You have not subscribed to the XM  satellite radio. The radio is being updated with the latest encryption\
code. Contact the XM satellite radio for subscription information. When a contact is cancel\
ed, you can
choose the “CH000” and all free −to− air channels.
The premium channel you selected is not authorized. Wait for about 2 seconds until the radio returns to
the previous channel or “CH001”. If it does not change automatica\
lly, select another channel. If you want
to listen to the premium channel, contact the XM  satellite radio.
NO SIGNALThe XM signal is too weak at the current location. Wait until your vehicle reaches a location with a stron-
ger signal.
LOADINGThe unit is acquiring audio or program information. Wait until the unit has received the information.
OFF AIRThe channel you selected is not broadcasting any programming. Select an\
other channel.
−−−−−There is no song/program title or artist name/feature associated with th\
e channel at that time. No action
needed.
−−−The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the
previous channel or “CH001”. If it does not change automatically, select another channel.
The XM  Listener Care Center is also available on the phone, please call (800) 967 −2346 during the following hours:
Monday – Saturday: 6 a.m. – 2 a.m. Eastern Time
Sunday: 8 a.m – 8 p.m. Eastern Time

265
NOTICE
This equipment has been tested and
found to comply with the limits for a
class B digital device, pursuant to
Part 15 of the FCC Rules. These
limits are designed to provide reason-
able protection against harmful inter-
ference in a residential installation.
This equipment generates, uses and
can radiate radio frequency energy
and, if not installed and used in ac-
cordance with the instructions, may
cause harmful interference to radio
communications. However, there is
no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful
interference to radio or television re-
ception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of
the following measures:
— Reorient or relocate the receiving
antenna.
— Increase the separation between
the equipment and receiver.
— Connect the equipment into an out-
let on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experi-
enced radio/TV technician for help.
Information to user
Alternation or modifications carried
out without appropriate authorization
may invalidate the user’s right to op-
erate the equipment.This XM tuner supports “Audio Ser-
vices” (Music and Talk) of only XM 
satellite radio and “Text Information”,
linked to the respective “Audio Ser-
vices”.
*Text Information includes, Station
Name, (Artist) Name, (Song) Title and
Category Name.

266
(a) Inserting or ejecting compact disc
Ty p e 1 :
Setting a single compact disc:
1. Push the “LOAD” button briefly.
The amber indicators at both ends of the
slot blinking. The amber blinking indicators
change to continuous green illumination. 2. Insert only one disc.
You can set a disc at the lowest empty
disc number.
After insertion, the set disc is automatical-
ly loaded.
If the label faces down, the disc cannot
be played. In this case, “CD CHECK” ap-
pears on the display.
If you need to insert the next disc, repeat
the same procedure to insert another disc.
Setting all the discs:
1. Push the “LOAD” button until you hear a beep.
The amber indicators at both ends of the
slot blinking. The amber blinking indicators
change to continuous green illumination. 2. Insert only one disc.
The amber indicators blink. 3. Insert the next disc after the amber blinking indicators change to contin-
uous green illumination.
4. Repeat this procedure until you in- sert all the discs.
To cancel the operation, push the “LOAD”
button.
Your automatic changer can store up to 6
discs.
If you do not insert the discs within 15
seconds after pushing the “LOAD” button,
the operation will be canceled automatical-
ly.NOTICE
Do not insert one disc stacked on top
of another one or feed them in con-
tinuously, to prevent discs from get-
ting stuck in the player.
Compact disc player operation
( Typ e 1 an d Typ e 2)

267
26p129c
Ejecting a single alone:
1. Touch the switch (16) to highlight the disc number you want to eject.
2. Push the “
” button for the com-
pact disc briefly.
At this time, the amber indicators of the
slot start blinking.
Ejecting all the discs:
Push the “
” button for the compact
disc until you hear a beep.
26p205c
The numbers of the trays where the com-
pact disc is not set are dimmed.
Ty p e 2 :
When you insert a disc, the player will
automatically start. To eject the disc,
push the “
” button.
(b) Playing a compact disc
Ty p e 1 :
Push the “DISC·AUX” button if the disc
is already loaded in the player.
“CD CHANGER” appears on the display.
The discs set in the player are played
continuously, starting with the last disc
you inserted. The disc number of the disc
currently being played, the track number
and the time from the beginning of the
program are shown on the display.
When play of one disc ends, the first
track of the following disc starts. When
play of the final disc ends, play of the
first disc starts again.

268
The player will skip any empty disc trays.
When the AUX adapter is in use, each
time you push the “DISC·AUX” button, the
audio switches the compact disc mode
and AUX mode alternately. For details
about AUX adapter, see page 278.
Ty p e 2 :
Push the “DISC·AUX” button if the disc
is already loaded in the player.
“CD” appears on the display.
The discs set in the player are played
continuously. The track number and the
time from the beginning of the program
are shown on the display.
26p205c
(c) Selecting a desired disc (Type 1 only)
Touch the desired disc number.
The selected disc number is highlighted in
green.
The player will start playing the selected
disc from the first track.(d) Selecting a desired track
“SEEK·TRACK” button:
Push the “SEEK·TRACK” button. The play-
er will start playing the selected track
from the beginning.
Track list screen:
Touch the desired track displayed on the
track list screen.
The track list screen cannot be displayed
while driving.
For details about the track list screen, see
“Displaying the track list” on page 270.

269
(e) Fast Forward/Reverse
Push the “SEEK·TRACK” button and hold
it to fast forward/reverse the disc. When
you release the switch, the player will
resume playing.
When fast forwarding, if you reach the
end of the final track, the player will go
back to the start track and continue op-
eration.
When reversing, if you reach the begin-
ning of the start track, reverse is can-
celled, even if you continue to hold down
the button.
26p234b
(f) Repeating the same track
Touch the “RPT” switch briefly. When the
track is finished, the player will automati-
cally go back to the beginning of the track
and play the track again. To cancel it,
touch the “RPT” switch once again.
(g) Repeating the same disc
Touch the “RPT” switch and hold it until
you hear a beep. When the disc is fin-
ished, the player will automatically go
back to the beginning of the disc and play
the disc again. To cancel it, touch the
“RPT” switch once again.
26p235b
(h) Listening to the tracks in the discyou are listening to, in random or-
der
Touch the “RAND” switch briefly, the sys-
tem selects a track in the disc you are
currently listening to. To cancel it, touch
the “RAND” switch once again.
(i) Listening to the tracks in all the discs set, in random order
Touch the “RAND” switch and hold it until
you hear a beep, the system selects a
track in all the discs which are set and
plays it. To cancel it, touch the “RAND”
switch once again.

270
26p218c
(j) Searching for a desired track
Touch the “SCAN” switch briefly, the play-
er will play the next track for 10 seconds,
then scan again. To select a track, touch
the “SCAN” switch a second time.
After all the tracks are scanned in one
pass, normal play resumes.
(k) Searching for a desired disc (Type 1 only)
Touch the “SCAN” switch and hold it until
you hear a beep, the track at the begin-
ning of each disc will be played for 10
seconds. To continue listening to the track
of your choice, touch the “SCAN” switch
a second time. After all the discs are scanned in one
pass, normal play resumes.
26p236b
(l) Displaying the track list
Touch the “TRACK LIST” switch.
The track list screen will be displayed.
If there are more than 6 tracks, touch “
”
or “
” to change the page.
If you touch a track, that track will be
played.
Only track names of 13 characters or less
can be displayed. Furthermore, track
names may not be displayed correctly or
at all, depending on the recorded content.