TOYOTA SIENNA 2007 Service Repair Manual

BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEMBC–99
BC
OK:
No scratches or foreign matter on the sensor tip.
NOTICE:
Check the speed sensor signal after the replacement
(See page BC-72).
NG
OK
(a) Remove the front drive shaft (See page DS-5).
(b) Check the sensor rotor serrations.
OK:
No scratches, missing teeth or foreign matter on
the rotors.
HINT:
If there is foreign matter in the rotor, remove it and check
the output waveform after reassembly.
NOTICE:
• Check the speed sensor signal after the
replacement (See page BC-72).
• When replacing the brake actuator assembly,
perform zero point calibration (See page BC-70).
NG
OKCLEAN OR REPLACE FRONT SPEED
SENSOR
8CHECK SPEED SENSOR ROTOR
R000948E06
REPLACE FRONT DRIVE SHAFT ASSEMBLY
(SPEED SENSOR ROTOR)
REPLACE BRAKE ACTUATOR ASSEMBLY

BC–100BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEM
BC
DESCRIPTION
Refer to DTCs C0200/31, C0205/32, C1235/35 and C1236/36 (See page BC-92).
HINT:
• DTC C0210/33 and C1238/38 are for the right rear speed sensor.
• DTC C0215/34 and C1239/39 are for the left rear speed sensor.
WIRING DIAGRAM
DTC C0210/33 Right Rear Wheel Speed Sensor Signal
DTC C0215/34 Rear Speed Sensor LH Circuit
DTC C1238/38Foreign Object is Attached on Tip of Rear
Speed Sensor RH
DTC C1239/39Foreign Object is Attached on Tip of Rear
Speed Sensor LH
DTC Code DTC Detection Condition Trouble Area
C0210/33
C0215/34When any of the following is detected:
1. At a vehicle speed of 10 km/h (6 mph) or more, an
open or short in the sensor signal circuit continues
for 1 sec. or more.
2. Momentary interruption of sensor signal faulty
wheel occurs 7 times or more.
3. Sensor signal circuit is open for 0.5 sec. or more.• Right rear and left rear speed sensor
• Each speed sensor circuit
• Speed sensor rotor
• Sensor installation
C1238/38
C1239/39With vehicle speed at 20 km/h (12 mph) or more,
sensor signal of faulty wheel generated noise for 5 sec.
or more. • Right rear and left rear speed sensor
• Sensor installation
F040100E04

BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEMBC–101
BC
INSPECTION PROCEDURE
(a) Connect the intelligent tester to the DLC3.
(b) Start the engine.
(c) Select the DATA LIST mode on the intelligent tester.
ABS / VSC:
(d) Check that there is no difference between the speed
value output from the speed sensor displayed by the
intelligent tester and the speed value displayed on the
speedometer when driving the vehicle.
OK:
There is almost no difference in the displayed
speed value.
HINT:
There is tolerance of +- 10 % in the speedometer
indication.
NG
OK
(a) INSPECTION USING OSCILLOSCOPE:
(1) Connect the oscilloscope to terminals RR+ - RR- or
RL+ - RL- of the skid control ECU.
(2) Drive the vehicle at approximately 19 mph (30 km/
h), and check the signal waveform.
OK:
A waveform as shown in a figure should be
output.
HINT:
• As vehicle speed (wheel revolution speed) in
creases, a cycle of the waveform narrows and
the fluctuation in the output voltage becomes
greater.
• hen noise is identified in the waveform on the
oscilloscope, error signals are generated due to
the speed sensor rotor's scratches, looseness or
foreign matter attached to it.
NOTICE:
When replacing the brake actuator assembly,
perform zero point calibration (See page BC-70).
NG
1READ VALUE ON INTELLIGENT TESTER (REAR SPEED SENSOR)
Tester Display Measurement Item/Range Normal Condition
WHEEL SPD RLWheel speed sensor (RL) reading / min.: 0
km/h (0 MPH, max.: 326 km/h (202 MPH)Actual wheel speed
WHEEL SPD RRWheel speed sensor (RR) reading / min.: 0
km/h (0 MPH, max.: 326 km/h (202 MPH)Actual wheel speed
Go to step 3
2CHECK SPEED SENSOR AND SENSOR ROTOR SERRATIONS
W004200E19
Go to step 6

BC–102BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEM
BC
OK
(a) 2WD
(1) Disconnect the skid control sensor connector.
(2) Measure the resistance according to the value(s) in
the table below.
Standard resistance:
LH
RH
(3) Measure the resistance according to the value(s) in
the table below.
Standard resistance:
LH
RH
NOTICE:
Check the speed sensor signal after
replacement (See page BC-72).
(b) 4WD
(1) Remove the seat cushion seatback.
(2) Disconnect the speed sensor connector.
(3) Measure the resistance according to the value(s) in
the table below.
Standard resistance:
LH
RH
(4) Measure the resistance according to the value(s) in
the table below REPLACE BRAKE ACTUATOR ASSEMBLY
3INSPECT REAR SPEED SENSOR
F041836E20
Tester Connection Specified Condition
(A27-1) - (A27-2) 0.9 to 2.1 k
Tester Connection Specified Condition
(A28-1) - (A28-2) 0.9 to 2.1 k
Tester Connection Specified Condition
(A27-1) - Body ground 10 k
or higher
(A27-2) - Body ground 10 k
or higher
Tester Connection Specified Condition
(A28-1) - Body ground 10 k
or higher
(A28-2) - Body ground 10 k
or higher
F013045E08
Tester Connection Specified Condition
A27-1 (RL+) - A27-2 (RL-) 0.9 to 1.3
Tester Connection Specified Condition
A28-1 (RR+) - A28-2 (RR-) 0.9 to 1.3

BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEMBC–103
BC
Standard resistance:
LH
RH
NOTICE:
Check the speed sensor signal after the
replacement. (See page BC-72)
NG
OK
(a) Disconnect the skid control ECU connector and the skid
control sensor connector.
(b) Measure the resistance according to the value(s) in the
table below.
Standard resistance:
LH
RH
(c) Measure the resistance according to the value(s) in the
table below.
Standard resistance:
LH
RH
NG
Tester Connection Specified Condition
A27-1 (RL+) - Body ground 1 M
or higher
A27-2 (RL-) - Body ground 1 M
or higher
Tester Connection Specified Condition
A28-1 (RR+) - Body ground 1 M
or higher
A28-2 (RR-) - Body ground 1 M
or higher
REPLACE REAR SPEED SENSOR
4CHECK HARNESS AND CONNECTOR (REAR SPEED SENSOR - SKID CONTROL ECU)
C119433E03
Tester Connection Specified Condition
S3-20 (RL+) - A27-1 (RL+) Below 1
S3-6 (RL-) - A27-2 (RL-) Below 1
Tester Connection Specified Condition
S3-5 (RR+) - A28-1 (RR+) Below 1
S3-19 (RR-) - A28-2 (RR-) Below 1
Tester Connection Specified Condition
S3-20 (RL+) - Body ground 10 k
or higher
S3-6 (RL-) - Body ground 10 k
or higher
Tester Connection Specified Condition
S3-5 (RR+) - Body ground 10 k
or higher
S3-19 (RR-) - Body ground 10 k
or higher
REPAIR OR REPLACE HARNESS OR
CONNECTOR

BC–104BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEM
BC
OK
(a) INSPECTION USING OSCILLOSCOPE:
(1) Connect the oscilloscope to terminals RR+ - RR- or
RL+ - RL- of the skid control ECU.
(2) Drive the vehicle at approximately 19 mph (30 km/
h), and check the signal waveform.
OK:
A waveform as shown in a figure should be
output.
HINT:
• As the vehicle speed (wheel revolution speed)
increases, a cycle of the waveform narrows and
the fluctuation in the output voltage becomes
greater.
• When noise is identified in the waveform on the
oscilloscope, error signals are generated due to
the speed sensor rotor's scratches, looseness or
foreign matter attached to it.
NOTICE:
When replacing the brake actuator assembly,
perform zero point calibration (See page BC-70).
NG
OK
(a) 2WD
(1) Check the sensor installation.
OK:
There is no clearance between the sensor and
rear axle carrier.
5CHECK SPEED SENSOR AND SENSOR ROTOR SERRATIONS
W004200E20
Go to step 6
REPLACE BRAKE ACTUATOR ASSEMBLY
6CHECK REAR SPEED SENSOR INSTALLATION
F010178E14

BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEMBC–105
BC
(b) 4WD
(1) Check the sensor installation.
OK:
There is no clearance between the sensor and
rear axle carrier.
The installation bolt is tightened properly.
Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)
NOTICE:
Check the speed sensor signal after the replacement
(See page BC-72).
NG
OK
(a) Remove the rear axle hub and bearing, or rear drive
shaft (See page AH-16 for 2WD, or DS-21 for 4WD).
(b) Check the sensor rotor serrations.
OK:
No scratches, missing teeth or foreign objects.
Result
NOTICE:
Check the speed sensor signal after the replacement
(See page BC-72).
B
BR03795E46
INSTALL REAR SPEED SENSOR
CORRECTLY
7CHECK SPEED SENSOR ROTOR
F042859E02
Result Proceed to
OKA
NG (for 2WD)B
NG (for 4WD)C
REPLACE REAR AXLE HUB AND BEARING
ASSEMBLY (SPEED SENSOR ROTOR)

BC–106BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEM
BC
C
A
(a) Remove the rear speed sensor (See page BC-190 for
2WD or BC-194 for 4WD).
(b) Check the sensor tip.
OK:
No scratches or foreign matter on the sensor tip.
NOTICE:
• Check the speed sensor signal after the
replacement (See page BC-72).
• When replacing the brake actuator assembly,
perform zero point calibration (See page BC-70).
NG
OKREPLACE REAR DRIVE SHAFT ASSEMBLY
(SPEED SENSOR ROTOR)
8CHECK REAR SPEED SENSOR TIP
CLEAN OR REPLACE REAR SPEED
SENSOR
REPLACE BRAKE ACTUATOR ASSEMBLY

BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEMBC–107
BC
DESCRIPTION
This solenoid goes on when signals are received from the ECU and controls the pressure acting on the
wheel cylinders to control the braking force.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
This code is detected when a problem is determined in the
brake actuator assembly.
The solenoid circuit is in the brake actuator assembly.
Therefore, solenoid circuit inspection and solenoid unit
inspection cannot be performed. Be sure to check if the DTC
code is output before replacing the brake actuator assembly.
DTC C0226/21 SFR Solenoid Circuit
DTC C0236/22 SFL Solenoid Circuit
DTC C0246/23 SRR Solenoid Circuit
DTC C0256/24 SRL Solenoid Circuit
DTC Code DTC Detection Condition Trouble Area
C0226/21Open or short circuit in front right solenoid circuit
(SFRR or SFRH) continues for 0.05 sec. or more.• Brake actuator assembly
• Each solenoid circuit
C0236/22Open or short circuit in front left solenoid circuit (SFLR
or SFLH) continues for 0.05 sec. or more.• Brake actuator assembly
• Each solenoid circuit
C0246/23Open or short circuit in rear right solenoid circuit (SRRR
or SRRH) continues for 0.05 sec. or more.• Brake actuator assembly
• Each solenoid circuit
C0256/24Open or short circuit in rear left solenoid circuit (SRLR
or SRLH) continues for 0.05 sec. or more.• Brake actuator assembly
• Each solenoid circuit
1RECONFIRM DTC
F045115E02

BC–108BRAKE CONTROL – VEHICLE STABILITY CONTROL SYSTEM
BC
(a) Clear the DTCs (See page BC-82).
(b) Turn the ignition switch to the ON position.
(c) Are the same DTCs recorded?
Result
NOTICE:
When replacing the brake actuator assembly,
perform zero point calibration (See page BC-70).
B
A
Result Proceed to
DTC is outputA
DTC is not outputB
PROCEED TO NEXT CIRCUIT INSPECTION
SHOWN IN PROBLEM SYMPTOMS TABLE
REPLACE BRAKE ACTUATOR ASSEMBLY