TOYOTA SUPRA 1986 Service Repair Manual

 
 
 
 
 
 
 
 
 
 
Crankshaft
(cont'd) 
 
 
 
 
 
 
 
 
 
Main bearing center wall thickness (Reference)
Mark 1
Mark 2
Mark 3
Mark 4
Mark 5
Crank pin diameter STD
U/S 0.25
Circle runout Maximum
Main journal taper and out±of±round Maximum
Crank pin taper and out±of±round Maximum 
 
 
 
 
 
 
 
 
 
1.994±1.997 mm (0.0785±0.0786 in.)
1.997±2.000 mm (0.0786±0.0787 in.)
2.000±2.003 mm (0.0787±0.0789 in.)
2.003±2.006 mm (0.0789±0.0790 in.)
2.006±2.009 mm (0.0790±0.0791 in.)
51.982±52.000 mm (2.0465±2.0472 in.)
51.745±51.755 mm (2.0372±2.0376 in.)
0.06 mm (0.0024 in.)
0.02 mm (0.0008 in.)
0.02 mm (0.0008 in.)
TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
 Timing belt plate X Oil pump (2JZ±GTE) 7.8 80 69 in.Vlbf
 Idler pulley X Oil pump 34 350 25
 Crankshaft pulley X Crankshaft 324 3,300 239
 Camshaft timing pulley X Camshaft 79 810 59
Timing belt tensioner X Oil pump2627020 Drive belt tensioner X Cylinder head 21 210 15 Drive belt tensioner damper X Tensioner arm (2JZ±GTE M/T) 20 200 14 Drive belt tensioner damper X Tensioner bracket (2JZ±GTE M/T) 20 200 14 EGR cooler X Cylinder head 8.8 90 78 in.Vlbf ECT sensor X Cylinder head (2JZ±GE) 20 200 14 ECT sender gauge X Cylinder head (2JZ±GE) 20 200 14
 Engine hanger X Cylinder head 39 400 29
 Camshaft position sensor X Cylinder head (2JZ±GTE) 8.8 90 78 in.Vlbf
 
 
 
Cylinder head X Cylinder block 1st
2nd
3rd 



34
Turn 905
Turn 905 
 
 
350 
 
 
25
 Camshaft bearing cap X Cylinder head 20 200 14
 No.4 timing belt cover X Cylinder head 8.8 90 78 in.Vlbf
 Cylinder head cover X Cylinder head 2JZ±GE
2JZ±GTE 8.3
5.4 85
55 74 in.Vlbf
48 in.Vlbf
 
 Intake manifold X Cylinder head 2JZ±GE
2JZ±GTE 


27
27 
 280
280 
 20
20
 Fuel inlet pipe X Delivery pipe 42 420 30 Intake manifold stay X Intake manifold 39 400 29
 Intake manifold stay X Cylinder block 39 400 29
 Water outlet X Cylinder head (2JZ±GTE) 21 210 15
 Vacuum control valve set X Intake manifold (2JZ±GE) 21 210 15
 
 
Air intake chamber X Intake manifold 2JZ±GE
2JZ±GTE 


27
27 
 
280
280 
 
20
20
 Air intake chamber stay X Cylinder head (2JZ±GE) 18 185 13
 Air intake chamber stay X Air intake chamber (2JZ±GE) 18 185 13
 Exhaust manifold X Cylinder head 39 400 29
Pressure tank X Intake manifold (2JZ±GTE)2121015 
 Main bearing cap X Cylinder block 1st
2nd
 


44
Turn 905
 
 450
 
 33
EG±138± ENGINEENGINE MECHANICAL

 Connecting rod cap X Connecting rod 1st
2nd 29
Turn 905 300 22
 
Oil nozzle X Crankshaft (2JZ±GTE)
 
8.8
 
90
 
78 in.Vlbf Rear oil seal retainer X Cylinder block 5.9 60 52 in.Vlbf Crankshaft position sensor X Cylinder block (2JZ±GTE) 8.8 90 78 in.Vlbf Engine mounting bracket X Cylinder block 58 590 43 Engine coolant drain plug X Cylinder block 29 300 22 Union for oil cooler X Cylinder block (2JZ±GTE) 39 400 29
 Knock sensor X Cylinder block 44 450 33
 Oil pressure switch X Cylinder block 14 150 11
 Fuel pipe support X Cylinder block 14 145 10
 Oil filter bracket X Cylinder block 88 900 65
 No.2 water bypass pipe X Water pump 21 210 15
 No.2 water bypass pipe X Cylinder block 21 210 15
 Flywheel X Crankshaft (M/T) 1st
2nd 49
Turn 905 500 36
 Drive plate X Crankshaft (A/T) 83 850 61 Clutch cover X Flywheel (M/T) 19 195 14 
 Cylinder block X Transmission 14 mm head
17 mm head 
 39
72 
 400
730 
 29
43
 Clutch service hole cover X Clutch housing (2JZ±GTE M/T) 12 120 9
 Drive plate X Torque converter clutch (A/T) 33 340 25
 Oil cooler tube X Union for transmission (A/T) 34 350 25
 Rear support member X Body 25 260 19
 Rear support member X Engine rear mounting insulator 13 135 10
 Front suspension crossmember X Engine mounting insulator 59 600 43
 Transmission shift lever X Shift lever retainer (M/T) 19 195 14
 Transmission control rod X Shift lever (A/T) 13 130 9
Clutch release cylinder X Transmission (M/T)131309 
Clutch line tube X No.1 oil pan
 
37
 
380
 
27 Ground strap X Transmission (M/T) 37 380 27 Fuel inlet hose X Fuel pipe support 29 300 22 
 A/C compressor X Cylinder block for stud bolt
for bolt and nut 
 26
52 
 265
530 
 19
38
 PS pump front bracket X Cylinder block (2JZ±GE) 58 590 43
 PS pump front bracket X Oil pump (2JZ±GE) 52 530 38
 PS pump housing X PS pump bracket 58 590 43
 PS pump bracket X A/C compressor 58 590 43
 PS pump bracket X Cylinder block 39 400 29
 PS pump rear stay X PS pump bracket 39 400 29
 PS pump rear stay X Intake manifold stay (2JZ±GE) 39 400 29
 Rear center floor crossmember brace X Body (2JZ±GTE) 28 290 21
No.2 front exhaust pipe X Exhaust manifold6263046 No.2 front exhaust pipe X Front exhaust pipe 58 590 43 Pipe support bracket X Transmission 43 440 32 Front exhaust pipe X Center exhaust pipe 58 590 43 Center exhaust pipe X Tailpipe 19 195 14 
 
Sub heated oxygen sensor
x Front exhaust pipe (2JZ±GE (California), 2JZ±GTE) 
 
20 
 
200 
 
14
± ENGINEENGINE MECHANICALEG±139

LUBRICATION SYSTEM
PREPARATION
SST (SPECIAL SERVICE TOOLS)
09032±00100 Oil Pan Seal Cutter
09228±07500 Oil Filter Wrench
09316±60010 Transmission & Transfer Bearing
Replacer
(09316±00010) Replacer Pipe
09816±30010 Oil Pressure Switch Socket
No.2 oil pan
Crankshaft front oil seal
RECOMMENDED TOOLS
09040±00010 Hexagon Wrench Set
09040±00020 Torx Socket E10
09200±00010Engine Adjust Kit
A/C compressor stud bolt
EQUIPMENT
 
 Oil pressure gauge 
 
 
 Precision straight edge 
  Oil pump
 
 Torque wrench 
 
± ENGINELUBRICATION SYSTEMEG±359

LUBRICANT
 Item Capacity Classification
 
 
 
 
 
Engine oil (2JZ±GE)
Dry fill
Drain and refill
w/ Oil filter change
w/o Oil filter change 
 
 
 
 
6.5 liters (6.9 US qts, 5.7 Imp. qts)
5.3 liters (5.6 US qts, 4.7 Imp. qts)
4.9 liters (5.2 US qts, 4.3 Imp. qts)
 
 
 
 
 
API grade SH, Energy±Conserving II
mutigrade engine oil or ILSAC multigrade
engine oil and recommended viscosity oil,
with SAE 5W±30 being preferred engine oil
 
 
 
 
Engine oil (2JZ±GTE)
Dry fill
Drain and refill
w/ Oil filter change
w/o Oil filter change 
 
 
 
6.5 liters (6.9 US qts, 5.7 Imp. qts)
5.0 liters (5.3 US qts, 4.4 Imp. qts)
4.7 liters (5.0 US qts, 4.1 Imp. qts)
 
 
 
 
API grade SH, Energy±Conserving II
mutigrade engine oil or ILSAC multigrade
engine oil and recommended viscosity oil
SSM (SPECIAL SERVICE MATERIALS)
 
 
 
 
08826±00080 Seal Packing Black or equivalent
(FIPG) 
 
 
 
Oil pump
No.1 oil pan
No.2 oil pan
 
 
 
08833±00080 Adhesive 1344,
THREE BOND 1344,
LOCTITE 242 or equivalent 
 
 
Oil pressure switch
Idler pulley pivot bolt
EG±360± ENGINELUBRICATION SYSTEM

OIL PRESSURE CHECK
1. CHECK OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or
thinning.
If oil quality is visibly poor, replace the oil.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ºLº and ºFº marks on the
dipstick.
If low, check for the leakage and add oil up to ºFº mark.
3. REMOVE ENGINE UNDER COVER
4. 2JZ±GTE:
REMOVE NO.2 AIR TUBE
Loosen the 2 hose clamps, and remove 2 bolts and air tube.
5. 2JZ±GTE M/T:
REMOVE DRIVE BELT TENSIONER DAMPER
Remove the 2 nuts and tensioner damper.
6. DISCONNECT A/C COMPRESSOR FROM ENGINE
(a) Loosen the drive belt tension by turning the drive belt
tensioner clockwise, and remove the drive belt.
(b) Remove the 4 bolts and nut.
(c) Using a torx socket (E10), remove the stud bolt.
(d) Disconnect the compressor connector.
(e) Remove 4 bolts and pull the compressor downward.
± ENGINELUBRICATION SYSTEMEG±361

7. REMOVE OIL PRESSURE SWITCH, AND INSTALL OIL
PRESSURE GAUGE
(a) Disconnect the oil pressure switch connector.
(b) Using SST, remove the oil pressure switch.
SST 09816±30010
(c) Install an oil pressure gauge.
8. REINSTALL A/C COMPRESSOR
(a) Temporarily install the A/C compressor with the 4 bolts.
(b) Connect the compressor connector.
(c) Install the compressor with the stud bolt, 4 bolts and nut.
Torque:
Stud bolt
26 NVm (265 kgfVcm, 19 ftVlbf)
Bolt and nut
52 NVm (530 kgfVcm, 38 ftVlbf)
(d) Install the drive belt.
9. WARM UP ENGINE
Allow the engine to warm up to normal operating tempera-
ture.
10. CHECK OIL PRESSURE
Oil pressure:
At idle
49 kPa (0.5 kgf/cm
2, 7.1 psi) or more
At 3,000 rpm (2JZ±GE) or 4,000 rpm (2JZ±GTE)
324±579 kPa
(3.3±5.9 kgf/cm
2, 47±84 psi)
11. DISCONNECT A/C COMPRESSOR FROM ENGINE
12. REMOVE OIL PRESSURE GAUGE, AND REINSTALL OIL
PRESSURE SWITCH
(a) Remove the oil pressure gauge.
(b) Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Part No. 08833±00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(c) Using SST, install the oil pressure switch.
SST 09816±30010
Torque: 14 NVm (150 kgfVcm, 11 ftVlbf)
(d) Connect the oil pressure switch connector.
13. REINSTALL A/C COMPRESSOR
14. START ENGINE AND CHECK FOR LEAKS
15. 2JZ±GTE M/T:
INSTALL DRIVE BELT TENSIONER DAMPER
Torque: 20 NVm (200 kgfVcm, 14 ftVlbf)
16. 2JZ±GTE:
REINSTALL NO.2 AIR TUBE
17. REINSTALL ENGINE UNDER COVER EG±362
± ENGINELUBRICATION SYSTEM

OIL AND FILTER REPLACEMENT
CAUTION:
wProlonged and repeated contact with mineral oil will re-
sult in the removal of natural fats from the skin, leading
to dryness, irritation and dermatitis. In addition, used en-
gine oil contains potentially harmful contaminants which
may cause skin cancer.
wExercise caution in order to minimize the length and fre-
quency of contact of your skin to used oil. Wear protec-
tive clothing and gloves. Wash your skin thoroughly with
soap and water, or use waterless hand cleaner, to remove
any used engine oil. Do not use gasoline, thinners, or sol-
vents.
wIn order to preserve the environment, used oil and used
oil filters must be disposed of only at designated dispos-
al sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap
(b) Remove the oil drain plug, and drain the oil into a container.
2. REPLACE OIL FILTER
(a) Using SST, remove the oil filter.
SST 09228±07500
(b) Check and clean the oil filter installation surface.
(c) Apply clean engine oil to the gasket of a new oil filter.
(d) Lightly screw the oil filter into place, and tighten it until the
gasket contacts the seat.
± ENGINELUBRICATION SYSTEMEG±363

(e) Using SST, tighten it an additional 3/4 turn.
SST 09228±07500
3. REFILL WITH ENGINE OIL
(a) To wipe off oil that has dripped onto the engine under cover,
remove the 4 screws and bend the under cover downward.
NOTICE:
wTo avoid damaging the silencer, do not bend the engine
under cover more than 150 mm.
wIf oil gets on the silencer, wipe it off with a dry rag.
(b) Clean and install the oil drain plug with a new gasket.
Torque: 38 NVm (375 kgfVcm, 27 ftVlbf)
(c) Fill with fresh engine oil.
Capacity:
2JZ±GE
Drain and refill
w/ Oil filter change
5.3 liters (5.6 US qts, 4.7 Imp. qts)
w/o Oil filter change
4.9 liters (5.2 US qts, 4.3 Imp. qts)
Dry fill
6.5 liters (6.9 US qts, 5.7 Imp. qts)
2JZ±GTE
Drain and refill
w/ Oil filter change
5.0 liters (5.3 US qts, 4.4 Imp. qts)
w/o Oil filter change
4.7 liters (5.0 US qts, 4.1 Imp. qts)
Dry fill
6.5 liters (6.9 US qts, 5.7 Imp. qts)
(d) Reinstall the oil filler cap.
4. START ENGINE AND CHECK FOR OIL LEAKS
5. RECHECK ENGINE OIL LEVEL EG±364
± ENGINELUBRICATION SYSTEM

OIL PUMP
COMPONENTS FOR REMOVAL AND
INSTALLATION
± ENGINELUBRICATION SYSTEMEG±365

EG±366± ENGINELUBRICATION SYSTEM