TOYOTA TERCEL 1996 Service Repair Manual
Page 571 of 1202
SF0XS-04
Z02772
Ohmmeter
Resistance kW
Temperature °C (°F) Acceptable 30
20
10
5
3
2
1
0.5
0.3
0.2
0.1
40 -20 0 20 60 80 100
(212) (176) (140) (104) (68) (32) (-4)
MF-46
- MFIINTAKE AIR TEMPERATURE (IAT) SENSOR
1996 TERCEL (RM440U)
INSPECTION
1. REMOVE IAT SENSOR
2. INSPECT IAT SENSOR
Using an ohmmeter, measure the resistance between the ter-
minals.
Resistance: Refer to the graph
If the resistance is not as specified, replace the sensor.
3. REINSTALL IAT SENSOR
Page 572 of 1202
SF0WO-03
- MFIMANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR
MF-47
571 Author: Date:
1996 TERCEL (RM440U)
MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR
COMPONENTS
Page 573 of 1202
SF0WP-03
Z19295
Voltmeter
ECMVacuum
PIM
E2
Voltage Drop:
Applied
Vacuum
kPa
mmHg
in.Hg
Vo l t a ge
drop V13.3
100
3.94
0.3 - 0.5
26.7 40.0 53.5 66.7
200
7.87
300
11.81400
15.75500
19.69
0.7 - 0.9 1.1 - 1.3 1.5 - 1.7 1.9 - 2.1 MF-48
- MFIMANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT POWER SOURCE VOLTAGE OF MAP SEN-
SOR
(a) Disconnect the MAP sensor connector.
(b) Turn the ignition switch ON.
(c) Using a voltmeter, measure the voltage between connec-
tor terminals VC and E2 of the wiring harness side.
Voltage: 4.5 - 5.5 V
(d) Turn the ignition switch to LOCK.
(e) Reconnect the MAP sensor connector.
2. INSPECT POWER OUTPUT OF MAP SENSOR
(a) Turn the ignition switch ON.
(b) Disconnect the vacuum hose from the MAP sensor.
(c) Connect a voltmeter to terminals PIM and E2 of the ECM,
and measure the output voltage under ambient atmo-
spheric pressure.
(d) Apply vacuum to the MAP sensor in 13.3 kPa (100 mmHg,
3.94 in.Hg) segments to 66.7 kPa (500 mmHg, 19.69
in.Hg).
(e) Measure the voltage drop from step (c) above for each
segment.
(f) Reconnect the vacuum hose to the MAP sensor.
Page 574 of 1202
SF0WM-03
P20326
Knock Sensor
Connector Knock Sensor
- MFIKNOCK SENSOR
MF-49
573 Author: Date:
1996 TERCEL (RM440U)
KNOCK SENSOR
COMPONENTS
Page 575 of 1202
SF0WN-01
P20327
SST
P01630
Ohmmeter MF-50
- MFIKNOCK SENSOR
1996 TERCEL (RM440U)
INSPECTION
1. REMOVE KNOCK SENSOR
(a) Disconnect the knock sensor connector.
(b) Using SST, remove the knock sensor.
SST 09816-30010
2. INSPECT KNOCK SENSOR
Using an ohmmeter, check that there is no continuity between
the terminal and body.
If there is continuity, replace the sensor.
3. REINSTALL KNOCK SENSOR
Torque: 45 N´m (450 kgf´cm, 33 ft´lbf)
Page 576 of 1202
SF0WK-03
- MFIHEATED OXYGEN SENSOR
MF-51
575 Author: Date:
1996 TERCEL (RM440U)
HEATED OXYGEN SENSOR
COMPONENTS
Page 577 of 1202
MF-52
- MFIHEATED OXYGEN SENSOR
576 Author: Date:
1996 TERCEL (RM440U)
Page 578 of 1202
SF1PZ-01
P20873
+B
HT Ohmmeter
- MFIHEATED OXYGEN SENSOR
MF-53
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT HEATER RESISTANCE OF MAIN HEATED
OXYGEN SENSOR (BANK 1 SENSOR 1)
(a) Disconnect the oxygen sensor connectors.
(b) Using an ohmmeter, measure the resistance between the
terminals +B and HT.
Resistance: 11 - 16 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 44 N´m (440 kgf´cm, 32 ft´lbf)
(c) Reconnect the oxygen sensor connectors.
2. INSPECT HEATER RESISTANCE OF SUB HEATED
OXYGEN SENSOR (BANK 1 SENSOR 2)
(a) Remove the passenger's seat.
(b) Take out the console box side of the floor carpet.
(c) Disconnect the oxygen sensor connector.
(d) Using an ohmmeter, measure the resistance between the
terminals +B and HT.
Resistance: 11 - 16 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 44 N´m (440 kgf´cm, 32 ft´lbf)
(e) Reconnect the oxygen sensor connectors.
(f) Reinstall the floor carpet.
(g) Reinstall the passenger's seat.
Page 579 of 1202
SF0WI-05
MF-54
- MFIENGINE CONTROL MODULE (ECM)
578 Author: Date:
1996 TERCEL (RM440U)
ENGINE CONTROL MODULE (ECM)
COMPONENTS
Page 580 of 1202
SF0WJ-01
- MFIENGINE CONTROL MODULE (ECM)
MF-55
1996 TERCEL (RM440U)
INSPECTION
1. REMOVE ECM
2. INSPECT ECM (See page DI-17)
3. REINSTALL ECM