TOYOTA TERCEL 1996 Service Repair Manual
Page 621 of 1202
LU08C-06
- LUBRICATIONOIL PUMP
LU-5
620 Author: Date:
1996 TERCEL (RM440U)
OIL PUMP
COMPONENTS
Page 622 of 1202
P21171
Tension Spring
Bracket
Drive Rotor O-RingPressure Regulator
Valve Body
Piston
Drain PlugDrive Rotor
Oil Pump Bldy
Oil Pump Pulleyx 9
Non-reusable partOil Panx 10 Oil Strainer RetainerSpring
Snap Ring
O-Ring
Oil Seal
Gasket
LU-6
- LUBRICATIONOIL PUMP
621 Author: Date:
1996 TERCEL (RM440U)
Page 623 of 1202
LU08D-05
P20907
EM9278
EM9755
P20160
- LUBRICATIONOIL PUMP
LU-7
1996 TERCEL (RM440U)
REMOVAL
HINT:
When repairing the oil pump, the oil pan and strainer should be
removed and cleaned.
1. REMOVE HOOD
2. REMOVE OIL DIPSTICK
3. DRAIN ENGINE OIL
4. REMOVE TIMING BELT (See page EM-12)
5. SUSPEND ENGINE WITH ENGINE SLING DEVICE
6. REMOVE CRANKSHAFT TIMING PULLEY(See page
EM-12)
7. w/ A/C:
REMOVE A/C COMPRESSOR AND MOUNTING
BRACKET
(a) Disconnect the compressor connector.
(b) Remove the 4 compressor mounting bolts.
HINT:
Put a side compressor, and suspend it.
(c) Remove the 4 bolts and compressor mounting
bracket.
8. DISCONNECT FRONT EXHAUST PIPE
(a) Remove the 2 bolts and the 2 compresson springs.
(b) Disconnect the exhaust pipe.
Page 624 of 1202
P21179
N00279
SST
SST
P21172
P21103
P21100
LU-8
- LUBRICATIONOIL PUMP
1996 TERCEL (RM440U)
9. REMOVE OIL PAN
(a) Remove the 10 bolts.
(b) Insert the SST blade between the cylinder block and oil
pan, cut off applied sealer and then remove the oil pan.
SST 09032-00100
NOTICE:
Do not use SST for the oil pump body side and rear oil
seal retainer.
Be careful not to damage the oil pan flange.
10. REMOVE OIL STRAINER
Remove the 3 bolts and oil strainer with the O-ring.
11. REMOVE PRESSURE REGULATOR VALVE
12. REMOVE OIL PUMP AND OIL PUMP PULLY
(a) Remove the 9 bolts and tension spring bracket.
Page 625 of 1202
P21099
P21032
- LUBRICATIONOIL PUMP
LU-9
1996 TERCEL (RM440U)
(b) Using a soft-faced hammer, carefully tap off the oil pump.
(c) Remove the oil pump body and O-ring.
(d) Using a vise, remove the nut and oil pump pulley.
Page 626 of 1202
LU08E-01
LU0106
LU-10
- LUBRICATIONOIL PUMP
1996 TERCEL (RM440U)
DISASSEMBLY
REMOVE PRESSURE REGULATOR VALVE
(a) Using snap ring pliers, remove the snap ring.
(b) Remove the retainer, spring and pressure regulator valve
piston.
Page 627 of 1202
LU08F-04
LU0144
P21820
P21819
LU1165
- LUBRICATIONOIL PUMP
LU-1 1
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT PRESSURE REGULATOR VALVE
Coat the valve piston with engine oil and check that it falls
smoothly into the valve hole by its own weight.
If necessary, replace the valve.
2. INSPECT ROTOR BODY CLEARANCE
Using a feeler gauge, measure the clearance between the driv-
en rotor and pump body.
Standard clearance:
0.10 - 0.16 mm (0.0039 - 0.0063 in.)
Maximum clearance:
0.20 mm (0.0079 in.)
If the clearance is greater than maximum, replace the oil pump
rotor set and/or pump body.
3. INSPECT TIP CLEARANCE
Using a feeler gauge, measure the clearance between both ro-
tor tips.
Standard clearance:
0.03 - 0.14 mm (0.0012 - 0.0055 in.)
Maximum clearance:
0.20 mm (0.0079 in.)
If the clearance is greater than maximum, replace the oil pump
rotor set.
4. INSPECT SIDE CLEARANCE
Using a feeler gauge and flat block, measure the side clearance
as shown.
Standard clearance:
2.91 - 2.97 mm (0.1145 - 0.1169 in.)
Minimum clearance:
2.90 mm (0.1142 in.)
If the clearance is greater than maximum, replace the oil pump
rotor set and/or pump body.
Page 628 of 1202
LU08G-03
EM9964
LU1170
Flush LU-12
- LUBRICATIONOIL PUMP
1996 TERCEL (RM440U)
REPLACEMENT
1. REMOVE OIL SEAL
Using a screwdriver, pry out the oil seal.
2. INSTALL OIL SEAL
(a) Using a socket wrench and hammer, tap in a new oil seal
until its suface is flush with the oil pump body edge.
(b) Apply MP grease to the oil seal lip.
3. REPLACE CRANKSHAFT FRONT OIL SEAL
(See page EM-83)
Page 629 of 1202
LU08H-01
- LUBRICATIONOIL PUMP
LU-13
1996 TERCEL (RM440U)
REASSEMBLY
INSTALL PRESSURE REGULATOR VALVE
(a) Insert the pressure regulator valve piston, spring and retainer.
(b) Using snap ring pliers, install the snap ring.
Page 630 of 1202
LU08I-05
EG0099
P21101
Marks
P21885
EG0097
Seal Diameter
2 - 3 mm
(0.08 - 0.12 in.)
A - AB -B
A
AB
B LU-14
- LUBRICATIONOIL PUMP
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL OIL PUMP
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the oil pump
and cylinder block.
Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the contact
surfaces and sealing grooves.
Thoroughly clean all components to remove all the
loose material.
Using a non-residue solvent, clean both sealing
surfaces.
(b) Place the driven rotors into the pump body with the marks
facing the front.
(c) Align the pully and oil pump drive shaft.
(d) Using a vise, install the oil pump pully and nut.
Torque: 37 N´m (370 kgf´cm, 27 ft´lbf)
(e) Apply seal packing to the oil pump as shown in the illustra-
tion.
Seal packing:
Part No. 08826-00080 or equivalent
Install a nozzle that has been cut to a 2 - 3 mm (0.08
- 0.12 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.