TOYOTA TUNDRA 2000 Owners Manual

TUNDRA (34413U)
101
Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:
Two- wheel drive modelsgear km/h (mph)
1 45 (28)
2 85 (53)
3 125 (78)
4 165 (112)
Four- wheel drive models gear km/h (mph)
H2º or H4º L4º
1 45 (28) 15 ( 9)
2 85 (53) 30 (18)
3 125 (78) 45 (28)
4 165 (103) 70 (43)
NOTICE
Do not downshift if you are going
faster than the maximum allowablespeed for the next lower gear.
Good driving practice

If it is difficult to shift into reverse, put
the transmission in neutral, release the
clutch pedal momentarily, and then try
again.

When towing a trailer, in order to main-
tain engine braking efficiency, do not
use the fifth gear.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
NOTICE
Make sure the vehicle is completely
stopped before shifting into reverse.
Use the front drive control lever to se-
lect the following transfer modes.
H2º (high speed position, two- wheel
drive): Lever at H2º
Use this for normal driving on dry, hard-
surfaced roads. This position gives greater
economy, the quietest ride and least wear.
H4º (high speed position, four- wheel
drive): Lever at H4º
Use this for normal driving on wet, icy or
snow- covered roads. This position pro-
vides greater traction than two- wheel
drive.
Four- wheel drive systemÐ
(a) Front drive control
(lever type)
ProCarManuals.com

TUNDRA (34413U)
102
Nº (neutral position): Lever at Nº
No power is delivered to the wheels. The
vehicle must be stopped.
L4º (low speed position, four- wheel
drive): Lever at L4º
Use this for maximum power and traction.
Use L4º for climbing or descending steep
hills, off- road driving, and hard pulling in
sand, mud or deep snow.
The 4WDº (four- wheel drive) indicator
light comes on when the H4º, Nº or L4º
mode is selected.
See (c) Shifting procedure (lever type)º
for further instructions.Use the 2WD/4HIº and 4LOº buttons
to select the following transfer modes.
1. 2WDº (high speed position, two- wheel drive): 2WD/4HIº and 4LOº
buttons left out
Use this for normal driving on dry,
hard- surfaced roads. This position
gives greater economy, the quietest
ride and least wear.
2. 4HIº (high speed position, four- wheel drive): 2WD/4HIº button pushed
in
The 4HIº (high speed four- wheel
drive) indicator light comes on when
the 4HIº mode is selected.
Use this for normal driving on wet, icy
or snow- covered roads. This position
provides greater traction than two-
wheel drive.
3. 4LOº (low speed position, four- wheel drive): With the 2WD/4HIº
button pressed in, push the 4LOº
button
The 4LOº (low speed four- wheel drive)
indicator light comes on when the
4LOº mode is selected.
Use this for maximum power and trac-
tion. Use 4LOº mode for climbing or
descending steep h ills, off- road driving,
and hard pulling in s and, mud or deep
snow.
(a) Front drive control
(button type)
ProCarManuals.com

TUNDRA (34413U)
103
See (c) Shifting procedure (button type)º
for further instructions.
Ty p e A
Ty p e B
The A.D.D. can be engaged or disen-
gaged by the shifting operations de-
scribed in (c) Shifting procedureº.
You should drive in four- wheel drive for
at least 16 km (10 miles) each month.
This will assure that the front drive com-
ponents are lubricated.
(b) A.D.D. (automatic
disconnecting differential)
ProCarManuals.com

TUNDRA (34413U)
104
SHIFTING BETWEEN H2º AND H4º
To shift from H2º to H4º, reduce the
vehicle speed to less than 80 km/h (50
mph) and move the front drive control
lever. You need not depress the clutch
pedal.
If you have trouble shifting in cold weath-
er, reduce the vehicle speed or stop the
vehicle and reshift.
CAUTION
Never move the front drive control
lever if wheels are slipping. Stop the
slipping or spinning before shifting.
To shift from H4º to H2º, simply move
the front drive control lever.
This can be done at any speed. You need
not depress the clutch pedal.
If the indicator light does not go off when
you shift the transfer into H2º, drive
straight ahead while accelerating or decel-
erating, or drive forward or backward in a
short distance. SHIFTING BETWEEN H4º AND L4º
To shift from H4º to L4º,
stop the
vehicle or reduce the vehicle speed to
less than 8 km/h (5 mph). With your foot
off the accelerator pedal, depress the
clutch pedal and move the front drive con-
trol lever.
To shift from L4º to H4º, depress the
clutch pedal and move the front drive con-
trol lever.
This can be done at any speed. SHIFTING BETWEEN H2º AND H4º
To shift from H2º to H4º,
reduce the
vehicle speed to less than 80 km/h (50
mph) and move the front drive control
lever.
If you have trouble shifting in cold weath-
er, reduce the vehicle speed or stop the
vehicle and reshift.
CAUTION
Never move the front drive control
lever if wheels are slipping. Stop the
slipping or spinning before shifting.
To shift from H4º to H2º, simply move
the front drive control lever.
This can be done at any speed.
If the indicator light does not go off when
you shift the transfer into H2º, drive
straight ahead while accelerating or decel-
erating, or drive forward or backward in a
short distance.
SHIFTING BETWEEN H4º AND L4º
To shift between H4º and L4º, stop
the vehicle and put the transmission in
Nº. With the brake pedal depressed,
move the front drive control lever.
(c) Shifting procedure
(lever type with manual
transmission) (c) Shifting procedure
(lever type with automatic
transmission)
ProCarManuals.com

TUNDRA (34413U)
105
SHIFTING BETWEEN º2WDº AND º4HIº
To shift from º2WDº to º4HIº, reduce
the vehicle speed to less than 100 km/h
(62 mph) and push in the º2WD/4HIº but-
ton.
If the 4HIº (high speed four- wheel drive)
indicator light flashes when you push in
the º2WD/4HIº button, this reminds you
that the transfer mode is not securely in
º4HIº mode. Drive straight ahead while
accelerating or decelerating.
If the 4HIº (high speed four- wheel drive)
indicator light flashes and the buzzer
sounds when you push in the º2WD/4HIº
button, this reminds you that the transfer
mode is not in º4HIº mode. Stop the ve-
hicle or reduce the vehicle speed to less
than 100 km/h (62 mph). Push the button
to turn it off, then once again to turn it
back on.
CAUTION
Never push the º2WD/4HIº button if
the wheels are slipping. Stop the slip-
ping or spinning before shifting.
To shift from º4HIº to º2WDº, push the
º2WD/4HIº button again to turn it off.
This can be done at any speed.
If the 4HIº (high speed four- wheel drive)
indicator light flashes when you push the
º2WD/4HIº button again to return to 2WDº
mode, this reminds you that the transfer
mode is not securely in º2WDº mode.
Drive straight ahead while accelerating or
decelerating, or drive forward or backward
in a short distance. SHIFTING BETWEEN º4HIº AND º4LOº
To shift from º4HIº to º4LOº,
stop the
vehicle and put the transmission into ºNº.
With the brake pedal depressed, push the
º4LOº button. If the º2WD/4HIº button left
out, push in the º2WD/4HIº button to se-
lect the º4HIº mode.
If the 4LOº (low speed four- wheel drive)
indicator light flashes and the buzzer
sounds for 3 seconds when you push the
º4LOº button, this reminds you that the
transfer mode is not in º4LOº mode. Drive
forward or backward in a short distance,
then stop the vehicle completely, put the
transmission securely into ºNº and push
the button again.
To shift from º4LOº to º4HIº, stop the
vehicle and put the transmission into ºNº.
With the brake pedal depressed, push the
º4LOº button.
If the 4LOº (low speed four- wheel drive)
indicator light flashes and the buzzer
sounds for 3 seconds when you push the
º4LOº button, this reminds you that the
transfer mode is not in º4HIº mode. Drive
forward or backward in a short distance,
then stop the vehicle completely, put the
transmission securely into ºNº and push
the button again.
(c) Shifting procedure
(button type)
ProCarManuals.com

TUNDRA (34413U)
106
SHIFTING BETWEEN º2WDº AND º4LOº
To shift from º2WDº to º4LOº, stop the
vehicle and put the transmission into ºNº.
With the brake pedal depressed, push the
º2WD/4HIº button in to select the º4HIº
mode, then push the º4LOº button.
If the 4LOº (low speed four- wheel drive)
indicator light flashes and the buzzer
sounds for 3 seconds when you push the
º4LOº button, this reminds you that the
transfer mode is not in º4LOº mode. Drive
forward or backward in a short distance,
then stop the vehicle completely, put the
transmission securely into ºNº and push
the button again.
To shift from º4LOº to º2WDº, stop the
vehicle and put the transmission into ºNº.
With the brake pedal depressed, push the
º2WD/4HIº switch again to turn it off. If the 4LOº (low speed four- wheel drive)
indicator light flashes and the buzzer
sounds when you push the º2WD/4HIº but-
ton, this reminds you that the transfer
mode is not in º2WDº mode. Push the
º2WD/4HIº button in to return to º4LOº
mode, drive forward or backward in a
short distance, then stop the vehicle com-
pletely, put the transmission securely into
ºNº and push the º2WD/4HIº button once
again.
If the 4LOº (low speed four- wheel drive)
indicator light flashes when you push the
º2WD/4HIº button, this reminds you that
the transfer mode is not in º2WDº mode.
Drive straight ahead while accelerating or
decelerating, or drive forward or backward
in a short distanse.
Parking brake
Pedal type
Lever type
ProCarManuals.com

TUNDRA (34413U)
107
When parking, firmly apply the parking
brake to avoid inadvertent creeping.
Pedal typeÐ
To set: Fully depress the parking brake
pedal. For better holding power, first de-
press the brake pedal and hold it while
setting the parking brake.
To release: Depress the parking brake
pedal once again.
Lever typeÐ
To set: Pull out on the lever. For better
holding power, first depress the brake
pedal and hold it while setting the parking
brake.
To release: Press the lock release button,
turn the lever, and push it in.
To remind you that the parking brake is
set, the parking brake reminder light in
the instrument panel remains on until you
release the parking brake.
CAUTION
Before driving, be sure the parking
brake is fully released and the park-
ing brake reminder light is off.
Cruise control
The cruise control allows you to cruise
the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off
the accelerator pedal.
Your cruising speed can be maintained up
or down grades within the limits of engine
performance, although a slight speed
change may occur when driving up or
down the grades. On steeper hills, a
greater speed change will occur so it is
better to drive without the cruise control.
CAUTION

To help maintain maximum control
of your vehicle, do not use the
cruise control when driving in
heavy or varying traffic, or on slip-
pery (rainy, icy or snow- covered) or
winding roads.

Avoid vehicle speed increases when
driving downhill. If the vehicle
speed is too fast in relation to the
cruise control set speed, cancel the
cruise control then downshift the
transmission to use engine braking
to slow down.
TURNING ON THE SYSTEM
To operate the cruise control, press the
CRUISE ON- OFFº button. This turns the
system on. The indicator light in the
instrument panel shows that you can now
set the vehicle at a desired cruising
speed. Another press will turn the system
completely off.
CAUTION
To avoid accidental cruise control en-
gagement, keep the CRUISE ON-
OFFº switch off when not using the
cruise control.
ProCarManuals.com

TUNDRA (34413U)
108
SETTING AT A DESIRED SPEED
On vehicles with automatic transmission,
the transmission must be in Dº before
you set the cruise control speed.
Bring your vehicle to the desired speed,
push the lever down in the SET/COASTº
direction and release it. This sets the ve-
hicle at that speed. If the speed is not
satisfactory, tap the lever up for a faster
speed, or tap it down for a slower speed.
Each tap changes the set speed by 1.6
km/h (1.0 mph). You can now take your
foot off the accelerator pedal.If you need accelerationÐfor example,
when passingÐdepress the accelerator
pedal enough for the vehicle to exceed
the set speed. When you release it, the
vehicle will return to the speed set prior
to the acceleration.
CAUTION
For manual transmission:
While driving with the cruise control
on, do not shift to neutral without
depressing the clutch pedal, as this
may cause engine racing or overrev-
ving.
CANCELLING THE PRESET SPEED
You can cancel the preset speed by:
a. Pulling the lever in the CANCELº
direction and releasing it
b. Depressing the brake pedal
c. Depressing the clutch pedal (manual
transmission)
If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto-
matically cancel out.
If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset
speed will also automatically cancel out. If the preset speed automatically cancels
out other than for the above cases, have
your vehicle checked by your Toyota deal-
er at the earliest opportunity.
RESETTING TO A FASTER SPEED
Push the lever up in the RES/ACCº direc-
tion and hold it. Release the lever when
the desired speed is attained. While the
lever is held up, the vehicle will gradually
gain speed.
However, a faster way to reset is to ac-
celerate the vehicle and then push the
lever down in the SET/COASTº direction.
RESETTING TO A SLOWER SPEED
Push the lever down in the SET/COASTº
direction and hold it. Release the lever
when the desired speed is attained. While
the lever is held down, the vehicle speed
will gradually decrease.
However, a faster way to reset is to de-
press the brake pedal and then push the
lever down in the SET/COASTº direction.
ProCarManuals.com

TUNDRA (34413U)
109
On vehicles with automatic transmission,
even if you turn off the overdrive switch
with the cruise control on, engine braking
will not be applied because the cruise
control is not cancelled. To decrease the
vehicle speed, reset to a slower speed
with the cruise control lever or depress
the brake pedal. If you use the brake
pedal, cruise control is cancelled.
RESUMING THE PRESET SPEED
If the preset speed is cancelled by pulling
the control lever or by depressing the
brake pedal or clutch pedal, pushing the
lever up in the RES/ACCº direction will
restore the speed set prior to cancellation.
However, once the vehicle speed falls be-
low about 40 km/h (25 mph), the preset
speed will not be resumed.CRUISE CONTROL FAILURE WARNING
If the CRUISEº indicator light in the
instrument cluster flashes when using the
cruise control, press the CRUISE ON-
OFFº button to turn the system off and
then press it again to turn it on.
If any of the following conditions then oc-
curs, there is some trouble in the cruise
control system.

The indicator light does not come on.

The indicator light flashes again.

The indicator light goes out after it
comes on.
If this is the case, contact your Toyota
dealer and have your vehicle inspected.
Clutch start cancel switch
To crank the engine without depressing
the clutch pedal, push the switch with
the ignition on.
The switch stays on as long as the igni-
tion is on. And it will automatically turn off
when the ignition is off. An indicator light
will illuminate to indicate the system is
operating.
This switch cancels the clutch start sys-
tem, which is designed to keep the starter
motor from operating if the clutch pedal is
not depressed all the way down.
The switch allows the vehicle to be driven
out of difficult situations by cranking the
engine with the clutch engaged.
ProCarManuals.com

TUNDRA (34413U)
11 0
Never use the switch for normal engine
starting. Be sure to follow the starting
procedure instructed in How to start the
engineº in Part 3.
ProCarManuals.com