check engine VOLKSWAGEN JETTA 1998 Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 01-51


V.A.G 1551
print-out Possible cause
Repair
01276
ABS hydraulic
pump
-V64-
Signal outside
tolerances
1)
ABS hydraulic pump
-V64-connector to
control module faulty- Perform output Diagnostic Test Mode (DTM)
Page 01
-74

Open circuit, short to
positive or Ground in
the wiring - Check wiring and connections using wiring
diagram

- Perform electrical checks from Page 01
-102

ABS hydraulic pump
-V64- faulty - If the ABS hydraulic pump -V64- runs free while
electrical check test step 18 performed Page
01-102 , replace ABS control module (w/EDL) -
J104-

ABS control module
(w/EDL) -J104- faulty
Repair Manual, Brake System, Repair Group 45;
Hydraulic unit, brake booster/brake master cylinder
- Assembly overview; Removing and installing
control module and hydraulic unit - Replace ABS control module (w/EDL) -J104-
1) Type of DTC; this DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
Стр. 31из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-52


V.A.G 1551
print-out Possible cause
Repair
01312
Drive train data
bus faulty
1)


or:
ABS control module (w/EDL) -
J104- incorrectly coded

Engine control module
incorrectly coded
Repair group 01 for relevant
engine code - Check ABS control module
(w/EDL) -J104- coding Page 01
-
58
- Check engine control module
coding

Open circuit, short to positive or
Ground in the wiring - Check wiring and connections
using wiring diagram

- Perform electrical checks Page
01-102
Drive train data
bus faulty
1)

Sporadic
Ignition/starter switch turned
too slowly - Erase DTC memory Page 01-56
- No further measures required
- Inform customer
1) The DTC "Drive train data bus" will not cause the ABS warning light -K47- or warning light for
brake system -K118- to light up. The ABS function is retained over the complete range.
Стр. 32из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-53


V.A.G 1551 print-out
Possible cause
Repair
01314
Engine control module
No communication
- Read measured value block
Page 01
-61 display group number
125

Open circuit, short to
positive or Ground in data
bus wiring - Check wiring and connections of
data bus wiring using wiring
diagram
- Perform electrical checks
Page 01
-102
01315
Transmission Control
Module (TCM)
1)
No communication
- Read measured value block
Page 01-61 display group number
125

Open circuit, short to
positive or Ground in data
bus wiring - Check wiring and connections of
data bus wiring using wiring
diagram
- Perform electrical checks
Page 01
-102
1) Vehicles with automatic transmission only.
Стр. 33из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-54


V.A.G 1551 print-
out Possible cause
Repair
01316
Brake control
module
No
communication
Open circuit, short circuit to
positive or Ground in data bus
wiring - Check data bus wiring and
connection using wiring diagram
- Perform electrical checks
Page 01
-102
Стр. 34из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-55


V.A.G 1551
print-out Possible cause
Repair
18256
Check Engine
Control Module
(ECM) memory
DTC in ECM
Repair Manual, Fuel Injection & Ignition, Repair
Group 01 for relevant engine code - Check engine control module DTC memory
65535
Control module
faulty ABS Control
Module (w/EDL)
-J104- faulty Repair Manual, Brake System, Repair Group 45;
Hydraulic unit, brake booster/brake master cylinder -
Assembly overview; Removing and installing control
module and hydraulic unit - Replace ABS control module (w/EDL) -J104-
Стр. 35из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-56


Diagnostic Trouble Code (DTC)
memory, erasing and ending output


Note:
All functions which could previously be
performed with V.A.G 1551 can also be
performed with the tester VAS 5051.

Test requirements:

DTC memory checked Page 01-28 .

1. Erasing DTC memory

-
Press key.
Rapid data transfer HELP
Select function XX Indicated on display
- Press keys -0- and -5-; 05 enters "Erase
DTC memory" function.
Rapid data transfer Q
05 - Erase DTC memor
y
Indicated on display
- Confirm entry with Q key
Rapid data transfer
DTC memory is erased!
Indicated on display
-
Press key.
Rapid data transfer HELP
Select function XX Indicated on display
Стр. 36из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-57


Warning!
DTC memor
y was not interrogated.
Indicated on display
Note:
Adhere exactly to test sequence: First
check DTC memory, then erase
2. Ending output
- Press keys -0- and -6-, to end output.
Rapid data transfer Q
06 - End output Indicated on display
- Confirm input with Q key.
Rapid data transfer HELP
Select function XX Indicated on display
ABS warning light -K47- and warning light
for brake system -K118- must go out after
approx. 2 seconds. - Switch ignition off.
- Disconnect V.A.G 1551 Scan Tool at
Data Link Connector (DLC).
- Switch ignition on.
Стр. 37из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-66



Test sequence and test tables with
measured values

Checking speed sensor allocation

Display group number 001

- Press keys 0, 0 and 1.

- Confirm entry with key Q.
Read measured value block
1
1 2 3 4
There are always 4 display zones -arrows-
in the measured value block. Decoding the
individual values in display zones 1 to 4 can
be read from the following tables.
Read measured value block 1
0 km/h 0 km/h 0 km/h 0 km/h
Indicated on display: (vehicle stationary)
Press C key for the next display group
number entry.
If the key is pressed, keys 0 and 8 for
work sequence "Read measured value
block" must be pressed again afterwards to
regain entry.
Стр. 46из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-67


Note:
For display group number 001 remember:
The actual wheel speeds are displayed. They serve to check the speed sensor allocation to the
wheel. (The vehicle must be raised and the wheel must be rotated by hand by a 2nd mechanic).
Read measured value block
1 Display group number: 001
0 km/h 4 km/h 0 km/h 0 km/h
Indicated on display: (Example)

Wheel speed at right rear speed sensor
(0 to 255 km/h)

Wheel speed at left rear speed sensor

(0 to 255 km/h)

Wheel speed at right front speed sensor
(0 to 255 km/h)

Wheel speed at left front speed sensor

(0 to 255 km/h)
Стр. 47из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-68



Checking speed sensor

Display group number 002

- Press keys 0, 0 and 2.

- Confirm entry with key Q.
Read measured value block
2
1 2 3 4
There are always 4 display zones -arrows-
in the measured value block. Decoding the
individual values in display zones 1 to 4 can
be read from the following tables.
Read measured value block 2
255 km/h 255 km/h 255 km/h 255 km/h
Indicated on display: (Vehicle stationary)
Press C key for the next display group
number entry.
If the key is pressed, keys 0 and 8 for
work sequence "Read measured value
block" must be pressed again afterwards to
regain entry.
Стр. 48из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program