VOLVO XC90 T8 2017 Owner´s Manual

MAINTENANCE AND SERVICING
* Option/accessory.519
Function A
– –
Tailgate window wiper 15
Fuel pump control module 15
Relay windings for engine compart- ment electrical module; Relay wind-ing for transmission oil pump 5
– –
Driver side front seat heating
*15
Passenger side front seat heating
*15
Coolant pump 10
– –
Front driver-side front door module 20
Active chassis control module
*20
– –
Sensus control module 10
– –
– –
Function
A
Front passenger-side front door module20
Display for rear seat convenience functions; On-board diagnostics (OBDII)
C
; Extra movement sensor
(certain markets only) C5
C
– –
Circuit breaker for fuses 53 and 58 15
A
Certain markets only.
B Not Excellence
C Excellence only
Related information
• Fuses (p. 509)
• Replacing fuses (p. 510)
• Fuses in the engine compartment (p. 511)
• Fuses in the cargo compartment (p. 520)

MAINTENANCE AND SERVICING
* Option/accessory.
520
Fuses in the cargo compartment The fuses in the cargo compartment help pro- tect electrical components such as power seats *, airbags and seat belt tensioners.

MAINTENANCE AND SERVICING
}}
521
The fuse box is under the storage compartment on the right side
There is a fuse removal tool on the inside of the fuse box cover. There are also positions in thefuse box for several extra fuses.

||
MAINTENANCE AND SERVICING
* Option/accessory.
522
Positions
• Fuses 13–17 and 21–36 are called "Micro".
• Fuses 1–12, 18–20 and 37 are called "MCase" and should only be replaced by atrained and qualified Volvo service technician.
Function
A
Heated rear window 30
Power rear seat (driver side)A
20A
Pneumatic suspension
* compres-
sor 40
Rear electric heater (passenger side)
30
120-volt socket between the rear seats
A 30
A
Rear electric heater (driver side) 30
Power rear seat (passenger side)
A
20A
– –
Power tailgate
* 25
Power front seat (passenger side)
*
module 20
Trailer hitch
* control module 40
Function
A
Seat belt tensioner module (pas- senger side)40
Internal relay windings 5
– –
Foot movement detection module for opening the power tailgate
*5
– –
Module for electrically folding third row seats
* 20
Trailer hitch
* control module 25
Power front seat (driver seat
*
module 20
Seat belt tensioner module (driver side)
40
Parking camera
* 5
– –
– –
Ionic air cleanerA
5A
Feed when ignition is switched on. 10
Function
A
Airbag and seat belt tensioner modules 5
Cooler; heated/cooled cup holder (rear)
A 10
A
Heated rear seat (driver side)
*15
– –
Blind Spot Information (BLIS)
*5
– –
Seat belt tensioner modules 5
Emission system actuator 5
– –
– –
Heated rear seat (passenger side)
* 15
– –
A
XC90 Excellence.
Related information
• Replacing fuses (p. 510)
• Fuses (p. 509)

MAINTENANCE AND SERVICING
523
•
Fuses in the passenger compartment (p. 516)
• Fuses in the engine compartment (p. 511)

MAINTENANCE AND SERVICING
524
Replacing bulbs
The halogen headlight bulbs 3
can be replaced
by the owner.
Before the halogen headlight bulbs can be replaced, that plastic covering over the headlighthousing has to be removed and the housing hasto be lifted out of the vehicle.
NOTE
Halogen headlights are not available on all models or in all markets. Consult your Volvo retailer if you are uncertain about the type of headlights in your vehicle.To do so:
Lift the rubber strip by pressing in toward the engine compartment.
Release the pins in the plastic covering's four clips by pressing them down with ascrewdriver or similar object and remove thecovering.
The turn signal, high/low beam, Daytime RunningLight and parking light bulbs will be accessiblewhen the plastic covering has been removed. Put the covering back in place in the reverse order.NOTE
The pins in the clips have to be pressed back completely before the clips are placed in theplastic covering. When the covering is put back in place, the pins must be pressed so that their upper sur-face is flush with the surface of the clip.
3 Halogen headlights are not available on all models.

MAINTENANCE AND SERVICING
}}
525
NOTE
•For information regarding any bulbs not mentioned in this section, please contactyour Volvo retailer or a trained andauthorized Volvo service technician.
• Always switch off the ignition before star-ting to replace a bulb.
• If an error message remains in the dis-play after a faulty bulb has been replaced,contact an authorized Volvo workshop.
• Condensation may form temporarily onthe inside of the lenses of exterior lightssuch as headlights, fog lights, or taillights.This is normal and the lights aredesigned to withstand moisture. Normally,condensation will dissipate after thelights have been on for a short time.
• The optional Active Bending Light bulbscontain trace amounts of mercury. Thesebulbs should always be disposed of by atrained and qualified Volvo service techni-cian.
CAUTION
Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.
WARNING
• The ignition should be switched off com- pletely (be in ignition mode
0) when
replacing bulbs.
• If the engine has been running just prior to replacing bulbs in the headlight hous-ing, please keep in mind that componentsin the engine compartment will be hot.
Front bulbs (vehicles with halogen headlights)
Low beam
High beam
Parking light/Daytime Running Light
Turn signal
(Not in use)

||
MAINTENANCE AND SERVICING
526
Taillight bulbs
Brake light (LED)
Side marker light (LED)
Backup light4
Taillight (LED)
Turn signal (LED)
Fog light (LED)
High-mounted brake light (LED)
Related information
•
Bulb specifications (p. 530)
• Removing the rectangular headlight cover (p. 526) •
Replacing High Beam headlight bulbs(p. 528)
• Replacing low beam headlight bulbs(p. 527)
• Ignition modes (p. 389)
Removing the rectangular headlight cover
Most of the bulbs in the headlight housing can be accessed when the rectangular cover hasbeen removed.
Before the rectangular cover can be removed, the plastic covering must be removed, see the article"Replacing bulbs" for information.
1. Loosen the cover's four screws with a T20 Torx screwdriver (1) but do not remove them completely (turning them 3–4 turns isenough).
2. Push the cover to the side.
3. Remove the cover.Put the cover back in place in the reverse order.
4 Must be replaced by a trained and qualified Volvo service technician.

MAINTENANCE AND SERVICING
527
Related information
•Replacing bulbs (p. 524)
Replacing low beam headlight bulbs
On models with halogen headlights, the low beam headlight bulb can be replaced by theowner.
Before the bulb can be replaced, the plastic cov- ering over the headlight housing has to be removed, see the article "Replacing bulbs."
CAUTION
Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.
Driver's side bulb housing shown
1. Remove the low beam round rubber cover from the headlight housing. 2. Remove the connector from the bulb.
3. Remove the bulb by pressing it slightly
upward and then pulling it out.
4. Insert the bulb in the socket. The bulb's guid- ing pin should point straight up.
5. Press the connector into place.
6. Put the rubber cover back into place.
Related information
• Replacing bulbs (p. 524)
• Bulb specifications (p. 530)

MAINTENANCE AND SERVICING
528
Replacing High Beam headlight bulbs
On models with halogen headlights, the High Beam headlight bulb can be replaced by theowner.
Before the bulb can be accessed, the headlight housing's rectangular cover must be removed,see the article "Removing the rectangular head-light cover."
CAUTION
Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.Driver's side bulb housing shown
1. Remove the bulb by turning the bulb holder upward and then pulling it straight out.
2. Carefully pry the plastic sleeve by the con- nector's locking lug to release it.
3. Remove the connector from the bulb.
4. Insert a new bulb.
5. Insert the bulb in the socket and turn it downward.
Related information
• Removing the rectangular headlight cover (p. 526)
• Bulb specifications (p. 530)
• Replacing bulbs (p. 524)
Replacing front turn signal bulbs On models with halogen headlights, the front turn signal bulb can be replaced by the owner.
Before the bulb can be accessed, the headlight housing's rectangular cover must be removed,see the article "Removing the rectangular head-light cover."
Driver's side headlight housing shown
1. Press the retaining catches together and pull
the bulb holder straight out.
2. The bulb holder and bulb must be replaced as one unit.
3. Press the new bulb holder into the socket.