ECU ASTON MARTIN V8 VANTAGE 2010 Workshop Manual

Silencer Assembly (09.01)
Exhaust (09.00)
Issue 5, January 2010 Workshop Manual 9-1-9
20. Coupe Only - Remove cable ties (x2) from LH and RH
HEGO sensor harnesses.
21. Remove nuts (x6), securing each catalyst to exhaust manifolds.
22. With assistance, remove catalysts (x2), release HEGO sensor harnesses from behind heat shield.
23. Coupe Only - Remove string from multiplugs.
24. Discard gaskets (x2) from exhaust manifolds.
25. Coupe Only - Remove bolts (x11), heatshields to centre,
LH and RH rear pipes. Remove heatshields.
Installation
1. Clean heatshields.
2. Coupe Only - Position heatshields to centre, LH and RH
rear pipes. Install and tighten bolts.
3. Install new flange gaskets to exhaust manifolds.
4. With assistance, install both catalysts, install and torque tighten nuts (x6).
5. Roadster Only - Install bolts (x4) and nuts (x2) to
catalyst heatshield.
6. Coupe Only - Feed HEGO sensor harnesses behind
heat shield, secure harnesses with cable ties.
7. Apply exhaust sealant to cent re pipe, install centre pipe
to catalysts and centre mounting. Do not torque clamp
nuts at this stage.
8. Roadster Only - Install centre exhaust mounting bolts
(x4).
9. Apply exhaust sealant to LH and RH rear pipes.
10. Install LH and RH rear pi pes to centre pipe. Do not
torque clamp nuts at this stage.
11. Install both rear rubber mountings and hanger brackets to silencer.
12. Position silencer on lifter . Install silencer, position
hangers, install and tighten bolts (x4).
13. Install front mountings to silencer, install and tighten bolts (x4).
14. Align silencer to rear pipes, install springs (x4) and bolts (x4). Do not torque bolts at this stage.
15. Install and align stub pipes (x2) to silencer and to trims in
bumper.
16. Align clamps, do not torque tighten.
17. Connect lines to both by-pass vacuum valves.
18. Coupe Only - Remove string from multiplugs.
19. Connect multiplugs to HEGO sensors. 20. Working from front to rear, set all exhaust to body
clearances.
21. Tighten all exhaust fixings to the correct torque.
22. Install subframe cross brace, install and torque tighten bolts (x4).
23. Position mounting brackets, install rear bumper diffuser. Install and tighten Allen bolts.
24. Install undertrays - vehicle set (refer to Workshop Manual procedure 01.02.PD Undertrays - Vehicle Set -
Renew).
25. Lower vehicle on ramp.
Attach lengths of string to th e HEGO sensor multiplugs. This
enables routing the HEGO se nsor harness behind the
exhaust heat shield on assembly.
WA R N I N G
GET THE AID OF ONE MORE PERSON WHEN YOU
INSTALL THE REAR EXHAUST SILENCER.
THE SILENCER IS HEAVY .
Ensure correct alignment of exhaust pipes and silencer before tightening of fixing clamps.

Pipes and Supports (09.03)
Exhaust System (09.00)
May 2007 Workshop Manual 9-2-1
Exhaust System (09.00)
Pipes and Supports (09.03)
Specifications
Maintenance
RH/LH Catalyst and Pipe Assembly-
Renew
Removal
1. Raise vehicle on ramp.
2. Remove rear exhaust silencer (refer to Workshop Manual procedure 09.00.KA Silencer and Bypass Valve
Assembly - Remove for Access and Refit).
3. Disconnect multiplugs (x2), HEGO sensors.
4. Release sensor lead from clip on heatshield.
5. Secure sufficient lengths of string to HEGO sensor multiplugs for assembly purposes.
6. Loosen LH and RH clamp nuts , catalysts to centre pipe.
7. Remove nuts (x3), catalyst to exhaust manifold.
8. With assistance, manoeuvre exhaust centre pipe assembly rearwards to release from catalysts.
9. With assistance, release and support weight of LH/RH catalyst from exhaust manifold.
10. Manoeuvre HEGO sensor le ads and remove cable tie.
Release HEGO sensor leads from behind heat shield.
Remove string from HEGO multiplugs.
11. Remove catalyst assembly.
12. Remove and discard gasket.
13. Remove HEGO sensors (x2) from catalyst.
Installation
1. Clean catalyst, mating joint faces and HEGO sensors.
2. Install and tighten HEGO sensors (x2) to catalyst. 3. Install new gasket to exhaust manifold flange.
4. With assistance, position cata
lyst, secure string (x2) to
HEGO multiplugs, feed sensor leads behind heat shield.
Install catalyst to exhaust manifold.
5. Install and torque tighten nuts (x3), catalyst to exhaust manifold.
6. Align centre pipe assembly to catalyst, torque tighten clamp nuts.
7. Remove string (x2), conne ct multiplugs (x2), HEGO
sensors.
8. Secure sensor lead in clip on heatshield.
9. Install rear exhaust silencer (refer to Workshop Manual procedure 09.00.KA Silencer and Bypass Valve
Assembly - Remo ve for Access and Refit).
10. Lower vehicle on ramp.
Exhaust Centre Pipe-Renew
Removal
1. Raise vehicle on ramp.
2. Remove pipe assembly exha ust rear - RH (refer to
Workshop Manual procedure 09.00. Pipe Assembly -
Exhaust - Rear - RH - Renew).
3. Remove pipe assembly exha ust rear - LH (refer to
Workshop Manual procedure 09.00.JB Pipe Assembly -
Exhaust - Rear - LH - Renew).
4. Loosen clamp nuts (x2), centre pipe to LH and RH catalysts.
5. Release centre pipe from mountings, LH and RH
catalysts, remove centre pipe.
6. Remove bolts (x3), heatshie ld to centre pipe, remove
heatshield.
7. Remove Torx screws (x4), mounting bracket to centre pipe, remove bracket.
Installation
1. Use a proprietary exhaust seal ant around all pipe joints
prior to installation of exhaust system.
2. Install mounting bracket to centre pipe, install and tighten Torx screws (x4).
3. Install heatshield to centre pipe, install and tighten bolts (x3).
4. Apply exhaust sealant to centre pipe joints.
Torque Figures
DescriptionNmlb. / ft.
Catalyst (nuts / bolts) 25.5-34.5 19-25.5
Catalyst (clamps) 19-22 14.5-16.5
Centre pipe to rear pipe (clamp) 39-51 29-38
Rear Pipe to Silencer (bolt) 28-33 21-24.5
Repair Operation Time (ROT)
Attach lengths of string to th e HEGO sensor multiplugs. This
enables routing the HEGO se nsor harness behind the
exhaust heat shield on assembly.
Repair Operation Time (ROT)

Pipes and Supports (09.03)
Exhaust System (09.00)9-2-2 Workshop Manual May 2007
5. Install centre pipe to both catalysts and centre mountings. Do not torque clamp nuts at this stage.
6. Install pipe assembly exha ust rear - LH (refer to
Workshop Manual procedure 09.00.JB Pipe Assembly -
Exhaust - Rear - LH - Renew).
7. Install pipe assembly exhaust rear - RH (refer to Workshop Manual procedure 09.00.HB Pipe Assembly
- Exhaust - Rear - RH - Renew).
8. Align and torque tighten exhaust system nuts/bolts.
9. Lower vehicle on ramp.
RH Exhaust Manifold-Renew
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove RH front wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
4. Loosen EGR pipe in valve.
5. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
6. Remove (nuts x2) EGR pipe from manifold, discard
gasket and tie aside.
7. Remove nut (x8) securing manifold to cylinder head
(refer to Fig. 1).
8. Remove nut (x2) on engine mountings.
9. Raise engine by approximately 25mm. 10. Remove exhaust manifold from vehicle and discard
gasket.
11. Remove heatshield from manifold (bolts x4)
Installation
1. Clean exhaust manifold and mating face on engine. Install new gasket to engine.
2. Install heatshield to manifold (bolts x4)
3. Install manifold to engine.
4. Install nut (x8) securing manifold to cylinder head.
5. Lower engine.
6. Install nuts (x2) on engine mounts.
7. Install (nuts x2) EGR pipe from manifold, clean mating face and fit new gasket (torque).
8. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
9. Tighten EGR pipe in valve (torque).
10. Install RH front wheel arch liner (refer to Workshop
Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
11. Lower vehicle on ramp.
12. Connect vehicle battery.
LH Exhaust Manifold-Renew
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove heatshield deflec tor, front floor (refer to
Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
4. Remove LH front wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
Repair Operation Time (ROT)
A090069
Repair Operation Time (ROT)
ItemCode
Exhaust Manifold-Renew LH09.00.CB
WAR NI NG
TO AVOID PERSONAL INJURY, I.E. SEVERE BURNS TO
THE SKIN, ALLOW EXHAUS T SYSTEM TO COOL
DOWN BEFORE REMOVING EXHAUST SYSTEM COMPONENTS.

Pipes and Supports (09.03)
Exhaust System (09.00)
May 2007 Workshop Manual 9-2-3
5. Remove nuts (x8), securing manifold to cinder head
(refer to Fig. 1).
6. Remove exhaust manifold, remove and discard gasket.
Installation
1. Clean manifold and mating face on engine and install
new gasket to engine.
2. Install manifold to engine.
3. Install nuts (x8) securing manifold to cylinder head.
4. Install LH front wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
5. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
6. Lower vehicle on ramp.
7. Connect vehicle battery.
RH Exhaust Manifold Gasket-Renew
Removal
1. Remove wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
2. Loosen EGR pipe in valve.
3. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
4. Remove nuts (x2), EGR pipe to manifold, discard gasket
and tie EGR pipe aside. 5. Remove nut (x8) securing ex
haust manifold to cylinder
head.
6. Remove nuts (x2) on engine mountings.
7. Raise engine by approximately 25mm. (care to be taken as inlet manifold can foul).
8. Remove exhaust manifold from vehicle and discard gasket.
Installation
1. Install new gasket to engine, clean mating face on engine.
2. Install manifold to engine.
3. Install nut (x8) securing manifold to cylinder head
(torque).
4. Lower engine.
5. Install nuts (x2) on engine mounts (torque).
6. Install (nuts x2) EGR pipe from manifold, clean mating face and fit new gasket (torque).
7. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
8. Tighten EGR pipe in valve (torque).
9. Install wheel arch liner (r efer to Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
LH Exhaust Manifold Gasket-Renew
Removal
1. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
2. Remove LH wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
3. Remove nut (x8) securing manifold to cylinder head.
4. Remove manifold from vehicle and discard gasket.
Installation
1. Install new gasket to engine, clean mating face on engine.
2. Install manifold to engine.
3. Install nut (x8) securing manifold to cylinder head
(torque).
4. Install LH wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
Fig. 1
Repair Operation Time (ROT)
302306BA090070
Repair Operation Time (ROT)

Pipes and Supports (09.03)
Exhaust System (09.00)9-2-4 Workshop Manual May 2007
5. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
Exhaust Gas Temperature Sensor-Renew
Removal
1. Raise vehicle on ramp.
2. Remove rear exhaust silencer (refer to Workshop Manual procedure 09.00.KA Silencer and Bypass Valve
Assembly - Remove for Access and Refit).
3. Disconnect sensor multiplugs (x2.
4. Release sensor leads from clips (x2) on heatshield.
5. Secure sufficient lengths of string to sensor multiplugs for assembly purposes.
6. Loosen rear LH and RH clamp nuts, catalysts to centre pipe.
7. Remove nuts (x3), catalyst to exhaust manifold.
8. With assistance, manoeuvre exhaust centre pipe assembly rearwards to release from catalysts.
9. With assistance, release and support weight of LH catalyst from exhaust manifold.
10. Manoeuvre sensor leads and remove cable tie. Release sensor leads from behind heat shield. Secure cable tie.
Remove string fr om multiplugs.
11. Remove catalyst assembly.
12. Remove and discard gasket.
13. Remove sensor from catalyst.
Installation
1. Clean catalyst mating joint faces.
2. Install and tighten sensor (x2) (torque).
3. Apply proprietary exhaust sealant around pipe joints.
4. Install new gasket to exhaust manifold flange.
5. With assistance, position catal yst, secure string (x2) to
multiplugs, feed sensor leads behind heat shield. Install
catalyst to exhaust manifold.
6. Install and torque tighten nuts (x3), catalyst to exhaust manifold. 7. Align centre pipe assembly to catalyst, torque tighten
clamp nuts.
8. Remove string (x2), connect multiplugs (x2), sensors.
9. Secure sensor leads in clips on heatshield.
10. Install rear exhaust silencer (refer to Workshop Manual procedure 09.00.KA Silencer and Bypass Valve
Assembly - Remove for Access and Refit).
11. Lower vehicle on ramp.
RH/LH Rear Exhaust Pipe Assembly-
Renew
Removal
1. Raise vehicle on ramp.
2. Remove rear undertray.
3. Remove rear silencer assembly (refer to Workshop Manual procedure 09.00.KA Silencer and Bypass Valve
Assembly - Remove for Access and Refit).
4. Remove bolts (x4), cross brace.
5. Loosen clamp nut, release/remove rear intermediate pipe from centre pipe.
6. Remove rear intermediate pipe through subframe.
7. Remove bolts (x4), heat shields (x2).
8. Remove clamp nut, bolt and washers (x2) from rear intermediate pipe.
Installation
1. Clean rear intermediate pipe and mating faces on centre pipe.
2. Install clamp bolt, washers and nut.
3. Position heat shields (x2), install and torque bolts (x4).
4. Apply a proprietary exhaus t sealant to clamp joint.
5. Install rear intermediate pipe to centre pipe.
6. Align rear intermediate pipe to silencer.
7. Install rear silencer assembly (refer to Workshop Manual procedure 09.00.KA Silencer and Bypass Valve
Assembly - Remove for Access and Refit).
8. Torque tighten clamp nut.
9. Install cross brace, install and torque tighten bolts (x4).
10. Install rear undertray.
11. Lower vehicle on ramp.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
ItemCode
Rear Exhaust Pipe Assembly-Renew RH09.00.HB
Rear Exhaust Pipe Assembly-Renew LH09.00.JB
WAR NI NG
TO AVOID PERSONAL INJURY, I.E. SEVERE BURNS TO
THE SKIN, ALLOW EXHAUS T SYSTEM TO COOL
DOWN BEFORE REMOVING EXHAUST SYSTEM COMPONENTS.

Fuel Tank and Lines (10.01)
Fuel (10.00)10-1-10 Workshop Manual May 2007
10. Remove recovery unit and fuel tank drainage adaptor.
11. Release the fuel filter hose to pump (x1) quick release
unions (see Fig. 2).
12. Release vent hose from fuel pump assembly (see Fig. 3).
13. Release fuel hose and tank harness from fuel pump bracket clip.
14. Disconnect wiring harness plugs (x2). 15. Install fuel pump removal tool (310-140) (see Fig. 4).
16. Turn the fuel pump anti-clockwise, release and
withdraw pump from mounting.
17. Remove fuel pump.
Installation
1. Position fuel pump in its mounting . Using the service tool, turn clockwise to secure fuel pump.
2. Secure fuel hose and tank harness to bracket
3. Install vent hose to fuel pump.
4. Connect hose to pump assembly.
5. Connect wiring harness multiplugs (x2).
6. Connect fuel filter pipes.
7. Install fuel tank service cover and clamp.
8. Install fuel tank cover with new seal.
9. Install luggage compartment front floor carpet and retainers (x6).
10. Install luggage compartment rear floor carpet.
11. Connect battery earth lead.
Fig. 2
Fig. 3
$%
$
Fig. 4
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilat e vehicle and work area to
remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
$

Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-13
22. Remove cable tie carbon canister to bracket (see Fig. 11).
23. Remove carbon canister from fuel tank (clips 4) (see Fig. 12)
24. Remove tank from support plate.
Installation
1. Position tank to support plate.
2. Install new cable tie behind carbon canister bracket.
3. Align and secure carbon canister to clips (x4).
4. Tighten cable tie around carbon canister.
5. Connect multiplug (x1) fuel tank harness.
6. Install nut (x1) fuel tank harness earth.
7. Secure fuel tank harness (clips x5).
8. Connect fuel vapour hose quick fit connection to tank.
9. With assistance position tank and secure with bolts (x14)
10. Install vacuum hose clip to tank bolts / studs (x4)
11. install vacuum hose clips to studs and secure vacuum
hose.
12. Install nuts (x5) oil cooler to body.
13. Install heatshield. 14. Connect vapour purge and fuel pipe to tank.
15. Position earth lead and secure with nut.
16. Connect fuel tank harness to main harness.
17. Connect evaporative emis
sion control assembly hose
and secure with jubilee clip.
18. install filler neck pipe and hose assembly to fuel tank.
19. Position filler neck pipe, hose assembly and sealing washer to body.
20. Install nut filler neck pipe and hose assembly to body.
21. Install bolt filler pipe brac ket to spring damper assembly.
22. install fuel filler cap
23. Install rear subframe (see Workshop Manual procedure
02.01.CA Subframe Assembly - Rear - Remove for
Access and Refit).
24. Connect vehicle battery.
Fuel Tank and Canister Assembly-
Remove for Access/Refit
Removal
1. Disconnect vehicle battery.
2. Remove rear subframe (see Workshop Manual procedure 02.01.CA Subframe Assembly - Rear -
Remove for Access and Refit).
Fig. 11
Fig. 12
Warning
The fuel tank is heavy. Fuel tank removal / replacement
is a two person operation.
$$
$%
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilate vehicle and work area to remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and dispose of fuel contaminated materials safely.
Warning
Fuel vapour is explosiv e. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to eliminate fire risk.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the
vehicle battery.

Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-15
17. With assistance support tank, remove bolts (x14) tank to body and remove fuel tank (see Fig. 6).
Installation
1. With assistance position tank and secure with bolts (x14)
2. Install vacuum hose clip to tank bolts / studs (x4)
3. install vacuum hose clips to studs and secure vacuum hose.
4. Install nuts (x5) oil cooler to body.
5. Install heatshield.
6. Connect vapour purge and fuel pipe to tank.
7. Position earth lead and secure with nut.
8. Connect fuel tank harness to main harness.
9. Connect evaporative emission control assembly hose and secure with jubilee clip.
10. install filler neck pipe and hose assembly to fuel tank.
11. Position filler neck pipe, hose assembly and sealing washer to body.
12. Install nut filler neck pipe and hose assembly to body.
13. Install bolt filler pipe bracket to spring damper assembly.
14. install fuel filler cap
15. Install rear subframe (see Workshop Manual procedure 02.01.CA Subframe Assembly - Rear - Remove for
Access and Refit). 16. Connect vehicle battery.
Fuel Tank Sender Assembly-Renew
Removal
1. Disconnect battery earth lead.
2. Release and remove luggage compartment rear floor
carpet.
3. Remove luggage compartment front floor carpet retainers (x6) and remove carpet.
4. Remove fuel tank cover, clean off the sealant around the aperture.
5. Remove nuts (x7) and release plate clamp and fuel tank service cover.
Fig. 6
Warning
The fuel tank is heavy. Fuel tank removal / replacement
is a two person operation.
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination. Remove contaminated material, open fuel containers
and waste fuel. Fully ventilate vehicle and work area to remove all fuel fumes.
$
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and dispose of fuel contaminated materials safely.
Warning
Fuel vapour is explosiv e. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to eliminate fire risk.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the vehicle battery.
Warning
Ensure there is adequate ventilation inside the vehicle
(i.e. place the vehicle in a well ventilated area, with the windows open).
Caution
The following procedure is completed inside the vehicle
cabin area. Extra care must be taken to ensure no fuel or
fuel vapours come into contac t with the vehicle interior.

Fuel Tank and Lines (10.01)
Fuel (10.00)10-1-16 Workshop Manual May 2007
6. Install the fuel tank drainage adaptor (see Fig. 1).
7. Connect the external pipe to a fuel recovery unit.
Recover the fuel in accordance with the recovery unit
instructions.
8. Remove the recovery unit and fuel tank drainage adaptor.
9. Disconnect fuel tank sender unit multiplug (see Fig. 2).
10. Release fuel tank sender assembly from bracket. 11. Remove fuel tank sender unit (see Fig. 3).
Installation
1. Install sender unit, secure to bracket and connect
multiplug .
2. Install nuts (x7) securing plate clamp and fuel tank
service cover.
3. Install fuel tank cover with new seal.
4. Install luggage compartment front floor carpet and retainers (x6).
5. Install luggage compartment rear floor carpet
.
6. Connect battery earth lead.
Fuel Vapour Pipe Assembly-Renew
Removal
1. Battery isolation switch off.
Fig. 1
Fig. 2
$
$
Fig. 3
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilat e vehicle and work area to
remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
ItemCode
Fuel Vapour Pipe Assembly-Renew 10.01.KA
Warning
Read and follow all fuel handling instructions (at the beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and disp ose of fuel contaminated
materials safely.
$

Fuel Tank and Lines (10.01)
Fuel (10.00)10-1-18 Workshop Manual May 2007
2. Disconnect vehicle battery
3. Remove RH wheel arch liner (see Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
4. Position container to collect fuel spillage.
5. Release fuel supply and vapour pipe from pipe clips (3).
6. Disconnect quick fit connector manifold supply pipe to fuel supply and vapour pipe.
7. Disconnect manifold supp ly pipe from fuel rail.
8. Release manifold supply pipe from pipe clips (x3) and
remove pipe.
Installation
1. Position manifold supply pipe and secure in clips (x3).
2. Connect manifold supply pipe to fuel rail.
3. Connect manifold supply pipe to fuel supply and vapour
pipe.
4. Secure fuel supply and vapour pipe in clips (x3).
5. Install wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
6. Connect vehicle battery.
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilat e vehicle and work area to
remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.