engine oil ASTON MARTIN V8 VANTAGE 2010 Owner's Guide

Lubrication System (03.02)
Engine (03.00)3-2-2 Workshop Manual Issue 5, Janauary 2010
Specifications
Engine Oil Specification
Maintenance
Oil Pressure Pump to Sump Gasket -
Renew
1. Remove crankshaft timing chain sprocket (refer to Workshop Manual procedure 03.09.AK Sprocket -
Crankshaft - Renew).
2. Install guide pin through lower hole on chain tensioner. 3. Remove bolt that attaches
the oil pressure pump chain
tensioner assembly to engine bedplate (refer to Figure
1).
4. Remove tensioner assembly.
5. Remove bolts (x3) that attach the oil pressure pump to sump.
6. Release chain from oil pres sure pump sprocket, remove
oil pump.
7. Remove and discard oil pressure pump gasket.
Installation
1. Clean oil pressure pump and mating face on sump.
2. Install new gasket to sump, align to dowels (x2).
3. Position oil pressure pump, install chain on pump sprocket.
4. Install oil pressure pump, align to dowels (x2), Install and torque tighten bolts (x3).
5. Install chain tensioner, install and torque tighten bolt, remove guide pin.
6. Install crankshaft timing chain sprocket (refer to Workshop Manual procedure 03.09.AK Sprocket -
Crankshaft - Renew).
Oil Pump Chain - Renew
Removal
1. Remove oil pressure pump gasket (refer to Workshop Manual procedure 03.02.AG Gasket - Oil Pressure
Pump to Sump - Renew)
Engine oil
Europe/Aus/USA Castrol Edge Sport 10W-60
To achieve the required high performance of synthetic
lubricants, do not mi x with mineral oils.
Capacity Europe (Litres)UK
(Pints)USA
(Qts.)
Full System 13 23 11
Service Fill 10 18 9
Torque Figures
DescriptionNmlb/ft
Oil filter 15 - 18 11-13
Sump plug 20 - 26 15-19
Sump bolts 20 - 22 15-16
Oil delivery pump bolts 19 - 23 14-17
Oil scavenger pump bolts 19 - 23 14-17
Oil scavenger filters 11 - 13 8-10
Oil temperature sensor 16 - 24 12-17
Oil pressure switch 11 - 15 8-11
Oil pump tensioner bracket 11 - 13 8-10
10W-60
AuthorityStandard
API SL/CF
ACEA A3/B3/B4
Oil 10W-60 has both API and ACEA and therefore meets
more demanding tests than eith er API or ACEA oils alone.
Repair Operation Time (ROT)
Figure 1
Repair Operation Time (ROT)
ItemCode
Oil Pump Chain-Renew 03.02.AJ
A0302274

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-3
2. Remove bolts (x3) that attach the oil scavenge pump to sump (refer to Figure 1).
3. Remove oil scavenge pump, remove and discard gasket (refer to Figure 2).
4. Release chain from oil pu mp drive sprocket, remove
chain (refer to Figure 3).Installation
1. Clean oil scavenge pump and mating face on sump.
2. Install new oil scavenge pump gasket, align on dowels (x2).
3. Install chain onto oil scavenge pump sprocket.
4. Install oil scavenge pump, align to dowels (x2), Install and torque tighten bolts (x3).
5. Install chain onto oil pump drive sprocket.
6. Install oil pressure pump gasket (refer to Workshop
Manual procedure 03.02.AG Gasket - Oil Pressure
Pump to Sump - Renew).
Oil Sump Pan - Renew
Removal
1. Remove oil sump (refer to Workshop Manual procedure
03.02.BN Pan - Oil Sump - Remove and Reseal).
2. Remove bolt that attach the crankshaft timing sensor, remove sensor (refer to Figure 1).
Figure 1
Figure 2
Figure 3
A0302274
A0302276
Repair Operation Time (ROT)
A0302305

Lubrication System (03.02)
Engine (03.00)3-2-4 Workshop Manual Issue 5, Janauary 2010
3. Remove oil pressure sensor (refer to Figure 2).
4. Remove engine electric coolant temperature sensor (refer to Figure 3).
5. Remove Torx screws (x4) that attach the oil filter plates
(x2) to sump. Remove plates (refer to Figure 4). 6. Install suitable bolt and remove filters (x2) from sump
(refer to Figure 5).
7. Remove oil filter adaptor (refer to Figure 6).
Figure 2
Figure 3
Figure 4
A0302306
A0302306A
A0302305A
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Figure 5
Figure 6
A0302308
A0302306B

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-5
8. Press out alternator mounting bushes (x2) from sump (refer to Figure 7).
9. Remove dowels (x4) from sump for oil pressure and scavenge pumps location (refer to Figure 8). 10. Remove Torx screws (x2) that attach the oil pump(s)
chain guide, remove chain gu ide (refer to Figure 9).
11. Remove oil plug from sump.
Installation
1. Clean chain guide, oil filter adaptor, filters (x2), sump plug , pump(s) dowels and crankshaft timing sensor.
2. Install alternator bushes.
3. Install oil filter adaptor.
4. Install filters (x2), install oil filter plates (x2), install and
torque tighten Torx screws (x4).
5. Install oil plug.
6. Install oil pump(s) dowels (x4).
7. Clean old sealant from sensor threads (x2).
8. Apply sealant to engine electric coolant temperature sensor threads, install and torque tighten sensor.
9. Apply sealant to oil pressure sensor threads, install and torque tighten sensor.
10. Install oil pump(s) chain guid e, Install and torque tighten
Torx screws (x2).
11. Install crankshaft timing sensor, install and torque tighten bolt.
12. Install oil sump (refer to Workshop Manual procedure 03.02.BN Pan - Oil Sump - Remove and Reseal).
Oil Sump Pan - Remove and Reseal
Removal
1. Remove oil pump(s) drive chain (refer to Workshop Manual procedure 03.02.AJ Chain - Oil Pump - Renew).
Figure 7
Figure 8
A030206C
A0302307
Figure 9
Repair Operation Time (ROT)
A0302307A

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-7
6. Remove bolts (x4) that attach the LH and RH HEGO sensor multiplug brackets to sump (refer to Figure 5).
7. Disconnect multiplug from A/C compressor.
8. Remove bolts (x4) that attach the A/C compressor to mounting bracket. Tie compressor aside.
9. Remove bolts (x2) that attach the inlet and outlet oil pipes to sump (refer to Figure 6).
10. Release both oil pipes toge ther from sump, remove and
discard O-ring seals from pipes. 11. Remove Torx bolts (x4) that attach the A/C compressor
mounting bracket to engine bedplate and sump.
Remove bracket (refer to Figure 7).
12. Note fitted position of clutch bleed tube bracket, remove bolts (x4) that attach the torque tube to sump
(refer to Figure 8).
Figure 5
WA R N I N G
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Figure 6
A030206C
A030247
Figure 7
Figure 8
A0302303
A0302304

Lubrication System (03.02)
Engine (03.00)3-2-8 Workshop Manual Issue 5, Janauary 2010
13. Remove bolts (x16) that attach the sump to engine bedplate (refer to Figure 9).
14. Release and remove sump.
Installation
1. Clean old sealant from sump flange and engine bedplate.
2. Ensure that sump flange and mating face on engine bedplate are clean and dry.
3. Apply a continuous 3mm diameter bead of RTV sealant to sump flange as recommended.
4. Ensure that there are no gaps in sealant track.
5. Install sump, install bolts (x16). Do not torque tighten at this stage.
6. Install bolts (x4), sump to torque tube, lightly tighten bolts and then loosen bolts.
7. Torque tighten sump bolts (x16) in the recommended sequence.
8. Torque tighten sump to torque tube bolts (x4).
9. Install A/C compressor mounting bracket, install and torque tighten Torx bolts (x4).
10. Lubricate and install new O-ring seals to oil pipes.
11. Install oil pipes in sump, install and torque tighten bolts (x2)
12. Install compressor, install and torque tighten bolts (x4). 13. Connect multiplug to A/C compressor.
14. Install LH and RH HEGO
sensor multiplug brackets to
sump. Install and torque tighten bolts (x4).
15. Secure harness clips (x6) in sump.
16. Connect multiplug to crankshaft timing sensor.
17. Connect multiplug to engine electric coolant temperature sensor.
18. Connect multiplug to oil pressure sensor.
19. Install oil pump(s) drive chain (refer to Workshop
Manual procedure 03.02.AJ Chain - Oil Pump - Renew).
Oil Cooler - Renew
Removal
1. Raise vehicle on ramp.
2. Remove undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
3. Remove pipes from oil cooler (position container to catch oil) (refer to Figure).
Figure 1
4. Remove oil cooler from body (bolts x4).
5. Remove duct from oil cooler (bolts x4).
Installation
1. Install duct from to cooler (bolts x4) (torque).
2. Install oil cooler to body (bolts x4) (torque).
3. Install pipes to oil cooler (torque).
4. Install undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
5. Lower vehicle on ramp.
Figure 9
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
A030206D
Repair Operation Time (ROT)
ItemCode
Oil Cooler - Renew 03.02.BX
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Caution
Make sure that all open ends of oil cooler pipes and oil cooler connections are plugged to prevent dirt or
foreign material entering the lubrication system.

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-9
6. Fill tank with approximately amount of displaced oil and replace cap.
7. Use handbook procedure to check oil level.
Oil Cooler Tank Assembly - Renew
Removal
1. Disconnect breather pipe qu ickfits (x2) from air cleaner
duct.
2. Remove throttle body du ct for access (clips x3).
3. Remove cap.
4. Disconnect top hose from engine (clip x1) tie aside
(catch coolant).
5. Remove breather pipe from oil tank (quick fit) (refer to Figure 1).
Figure 1
6. Remove pipes (x2) fr om oil tank, tie aside.
7. Raise vehicle on ramp.
8. Remove undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
9. Drain oil tank. 10. Remove bottom pipe (x1) from oil tank (refer to Figure
2).
Figure 2
11. Remove bolts (x3) that attach the oil thermostat to body (allows oil hose movement).
12. Lower ramp.
13. Remove bolts (x4) that attach the tank to body and lift out.
Installation
1. Position tank to body and fit bolts (x4) (torque).
2. Install oil pipes to tank (torque).
3. Connect breather hose.
4. Connect top hose to engine (clip x1).
5. Raise vehicle on ramp.
6. Install bottom oil pipe to tank (torque).
7. Install bolts (x3) that attach the oil thermostat to body (torque).
8. Install undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
9. Lower vehicle.
10. Install throttle body duct.
11. Connect breather pipe quickf its (x2) to air cleaner duct.
12. Fill tank with approximately amount of displaced oil and replace cap.
13. Use handbook procedure to check oil level.
14. Top up coolant.
Thermostat - Renew
Removal
1. Drain Coolant (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
2. Release breather valve (bolt x1) and tie aside.
3. Unclip engine harness for access (x4).
4. Remove one end of engine breather hoses for access (x3).
Repair Operation Time (ROT)
A030243
Repair Operation Time (ROT)
A030244

Lubrication System (03.02)
Engine (03.00)3-2-10 Workshop Manual Issue 5, Janauary 2010
5. Remove breather valve bracket for access (nuts x2 bolt x1).
6. Remove thermostat housing from manifold (bolt x3).
7. Remove thermostat and sealing ring.
Installation
1. Install new thermostat and sealing ring .
2. Install thermostat housing (torque).
3. Install breather valve bracket.
4. Install breather hoses (x3) and clip.
5. Clip engine harness.
6. Install breather valve.
7. Refill coolant (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
Oil Cooler Tank Pipe Assembly - Renew
Removal
1. Remove oil pipe from oil tank (refer to Figure 1).
Figure 1
2. Raise vehicle on ramp.
3. Remove undertray (refer to Workshop Manual
procedure 01.02.NB Undertray - Front - Renew).
4. Remove RH air filter box (refer to Workshop Manual
procedure 03.12.DH Cleaner Assembly - Engine Air -
RH - Renew).
5. Unclip pipe (x4) from inner wing. 6. Remove pipe from oil cool
er and pull out from inner
wing (position container to catch oil) (refer to Figure 2).
Figure 2
Installation
1. Install pipe to oil cooler (torque) through inner wing .
2. Clip pipe (x4) to inner wing.
3. Install undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
4. Install RH air filter box (refer to Workshop Manual
procedure 03.12.DH Cleaner Assembly - Engine Air -
RH - Renew).
5. Lower vehicle on ramp.
6. Install pipe to oil tank (torque) ensure correct alignment in oil tank bracket.
7. Fill tank with approximatel y amount of displaced oil and
replace cap.
8. Use handbook procedure to check oil level.
Oil Thermostat to Tank Tube Assembly -
Renew
Removal
1. Disconnect breather pipe qu ickfits (x2) from air cleaner
duct.
2. Remove throttle body duct for access (clips x3).
Repair Operation Time (ROT)
A030241Repair Operation Time (ROT)
ItemCode
Oil Thermostat to Tank Tube Assembly
- Renew 03.02.CD
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
A030219

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-11
3. Remove pipes from oil tank (refer to Figure 1).
Figure 1
4. Raise vehicle on ramp.
5. Remove undertray (refer to Workshop Manual procedure. 01.02.NB Undertray - Front - Renew).
6. Remove pipe from oil thermostat (position container to catch oil) (refer to Figure 2).
Figure 2
Installation
1. Install pipe to oil thermostat (torque) ensure correct alignment in oil tank bracket.
2. Install undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
3. Lower vehicle on ramp.
4. Install oil pipe to tank.
5. Install throttle body duct.
6. Connect breather pipe quickf its (x2) to air cleaner duct.
7. Fill tank with approximately amount of displaced oil and replace cap.
8. Use handbook procedure to check oil level.
Oil Pump Inlet Tube Assembly - Renew
Removal
1. Remove the PAS pump (refer to Workshop Manual procedure 03.05.AA Pump - Power Steering - Renew).
2. Remove pipe from oil contro ller (position container to
catch oil).
3. Remove bolt, pipes to bracket (refer to Figure 1).
Figure 1
4. Remove LH exhaust manifo ld (refer to Workshop
Manual procedure 09.00.CD Gasket - Exhaust Manifold
- LH - Renew).
5 . R e m o v e h a r n e s s t o p i p e c l i p ( r e f e r t o F i g u r e 2 ) .
Figure 2
6. Remove bolts that attach the oil pipes to block.
7. Release both pipes from bl ock and remove inlet pipe.
Installation
1. Renew O-ring on remaining oil pipe.
2. Install inlet pipe and position both pipes into block.
A030244
A030246
Repair Operation Time (ROT)
A030248
A030247

Lubrication System (03.02)
Engine (03.00)3-2-12 Workshop Manual Issue 5, Janauary 2010
3. Install bolts that attach th e oil pipes to block (torque).
4. Install LH exhaust manifold (refer to Workshop Manual
procedure 09.00.CD Gasket - Exhaust Manifold - LH -
Renew).
5. Install bolt, pipes to bracket.
6. Install harness clip to pipe.
7. Install pipe to oil controller (torque).
8. Install P.A.S pump (refer to Workshop Manual procedure 03.05.AA Pump - Power Steering - Renew).
9. Fill tank with approximately amount of displaced oil and replace cap.
10. Use handbook procedure to check oil level.
Oil Pump Inlet Tube Assembly - Renew
Removal
1. Remove the PAS pump (refer to Workshop Manual procedure 03.05.AA Pump - Power Steering - Renew).
2. Remove pipe from oil controller (position container to catch oil).
3. Remove bolt, pipes to bracket (refer to Figure 1).
Figure 1
4. Remove LH exhaust manifold (refer to Workshop Manual procedure 09.00.CD Gasket - Exhaust Manifold
- LH - Renew). 5 . R e m o v e h a r n e s s t o p i p e c l i p ( r e f e r t o F i g u r e 2 ) .
Figure 2
6. Remove bolts that attach the oil pipes to block.
7. Release both pipes from bl
ock and remove inlet pipe.
Installation
1. Renew O-ring on remaining oil pipe.
2. Install inlet pipe and position both pipes into block.
3. Install bolts that attach the oil pipes to block (torque).
4. Install LH exhaust manifold (refer to Workshop Manual
procedure 09.00.CD Gasket - Exhaust Manifold - LH -
Renew).
5. Install bolt, pipes to bracket.
6. Install harness clip to pipe.
7. Install pipe to oil controller (torque).
8. Install P.A.S pump (refer to Workshop Manual procedure 03.05.AA Pump - Power Steering - Renew).
9. Fill tank with approximatel y amount of displaced oil and
replace cap.
10. Use handbook procedure to check oil level.
Oil Pump Outlet Tube Assembly - Renew
Removal
1. Remove PAS pump (refer to Workshop Manual procedure 03.05.AA Pump - Power Steering - Renew).
Repair Operation Time (ROT)
A030248
Repair Operation Time (ROT)
ItemCode
Oil Pump Outlet Tube Assembly -
Renew 03.02.CF
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
A030247