steering ASTON MARTIN V8 VANTAGE 2010 Repair Manual

Steering Column (11.04)
Steering (11.00)11-4-6 Workshop Manual Issue 4, November 2008

Steering Column Switches (11.05)
Steering (11.00)
Issue 4, November 2008 Workshop Manual 11-5-1
Steering (11.00)
Steering Column Switches (11.05)
Maintenance
Ignition Switch-Renew (Pre-08 MY Only)
Remove
1. Operate the driver's seat to its lowest and most rearward position.
2. Remove the steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering Column - Remove and
Install’, page 11-4-4).
3. Disconnect the vehicle battery.
4. Turn the steering wheel to the centre position until the steering lock engages.
5. Remove the screw that attaches the load-spread plate to the column.
6. Remove the mounting bracket for the column shrouds.
7. Release the two clips that attach the column switch harness to the load-spread plate.
8. Release the steering column switch from the column (to give access).
9. Release the ignition switch from the column.
10. Disconnect the electrical connector from the ignition
switch.
Install
1. Connect the electrical connector to the ignition switch.
2. Install the ignition switch onto the column.
3. Install the steering column switch.
4. Put the load-spread plate in position and attach the two harness clips.
5. Install the screw that attaches the load-spread plate.
6. Install the steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering Column - Remove and
Install’, page 11-4-4).
7. Connect the vehicle battery.
8. Operate the driver's seat to its initial position.
Steering Column Stalk Assembly Switch-
Renew (Pre-08 MY Only)
Remove
1. Operate the driver's seat to its lowest and most rearward position.
2. Remove the top and bottom shrouds from the steering column (Refer to ’Top and Bottom Shrouds for the
Steering Column - Remove and Install’, page 11-4-4).
3. Remove the screw that attaches the load-spread plate to the steering column and remove the load-spread plate.
Figure A11-04-1668
4. Collect the mounting bracket for the column shrouds.
5. Release the two clips that attach the column switch harness to the load-spread plate.
6. Disconnect the three electrical connectors from the steering column switches.
7. Release the clips and remove steering column switches from the column.
Install
1. Install the steering column switches and make sure that the clips engage.
2. Connect the three electrical connectors to the column switches.
3. Put the load-spread plate in position and install the two harness clips.
4. Install the screw to attach the load-spread plate.
5. Install the top and bottom steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering
Column - Remove and Install’, page 11-4-4).
6. Connect the vehicle battery.
7. Put the drivers seat and the steering column back to their initial positions.
Repair Operation Time (ROT)Repair Operation Time (ROT)

Steering Column Switches (11.05)
Steering (11.00)
11-5-2 Workshop Manual Issue 4, November 2008
Cruise Control Switch-Renew
Remove
1. Remove airbag module (Refer to ’Driver’s Airbag Module - Remove and Install’, page 11-6-1).
2. Remove the cruise control switch.
Install
1. Install the cruise control switch.
2. Make sure that the routing of the switch harness is correct.
3. Install the airbag module (Refer to ’Driver’s Airbag Module - Remove and Install’, page 11-6-1).
Indicator Switch for th e Steering Column
- Remove and Install
Remove
1. Remove the top shroud from the steering column (Refer to ’Top Shroud for the Steering Column - Remove and
Install’, page 11-4-1).
2. Release the clips that attach the indicator switch to its mounting.
3. Release the indicator switch from its mounting.
4. Disconnect the electrical connector for the indicator switch.
5. Remove the indicator switch.
Install
1. Connect the electrical connector to the indicator switch.
2. Install the indicator switch in the mounting.
3. Make sure that the clips that attach the switch are correctly engaged.
4. Install the top shroud to the steering column (Refer to ’Top Shroud for the Steering Column - Remove and
Install’, page 11-4-1).
Airbag Rotary Coupler Assembly -
Remove and Install
Remove
For Pre-08MY vehicles:
1. Put the key in the ignition switch and turn it to position 1 to release the Electronic Steering Column
Lock (ESCL).
For 08MY vehicles or newer:
2. Put the Emotion Control Unit (ECU) into the docking station at position 2 to release the ESCL..
3. Disconnect the vehicle battery.
4. Turn the steering wheel to get access to one of the two M6 screws that attach the airbag module (Refer to
FIgure 1).
Figure 1
5. Remove the M6 screw.
6. Turn the steering wheel to get access to the second M6 screw that attaches the airbag module.
7. Remove the second M6 screw.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
Repair Operation Time (ROT)
ItemCode
Airbag Rotary Coupler Assembly -
Remove and Install 11.06.CM
WAR NI NG
LEAVE THE VEHICLE FOR TWO MINUTES AFTER YOU
DISCONNECT THE BATTERY BEFORE YOU DO WORK. IF YOU DO NOT, THE AIRBAG SYSTEM CAN OPERATE
AND CAUSE INJURY.

Steering Column Switches (11.05)
Steering (11.00)
Issue 4, November 2008 Workshop Manual 11-5-3
8. Move the airbag module to get access to the two electrical connectors (Refer to FIgure 2).
Figure 2
9. Disconnect the two electrical connector for the airbag module.
10. Remove the airbag module and keep it in an approved storage area.
11. Turn the steering to the centre position.
12. Disconnect the electrical connector for the steering
wheel harness (Refer to FIgure 3).
Figure 3
13. Remove the M10 Torx screw that attaches the steering wheel (Refer to FIgure 4).
Figure 4
14. Remove the steering wheel assembly. 15. Apply tape to hold the rotary coupler in its central
position (Refer to FIgure 5).
Figure 5
16. Remove the top and bottom steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering
Column - Remove and Install’, page 11-4-4).
17. Remove the screw that attaches the load-spread plate to the steering column (Refer to FIgure 6).
Figure 6
18. Remove the load-spread plate.
19. Release the clips that attach the column switches to the rotary coupler.
20. Remove the column switches from the rotary coupler.

Steering Column Switches (11.05)
Steering (11.00)
11-5-4 Workshop Manual Issue 4, November 2008
21. Remove the electrical conne ctor (1) from the rotary
coupler (Refer to FIgure 7).
Figure 7
22. Release the two clips that attach the rotary coupler to the steering column and remove the rotary coupler.
Install
1. Put tape on the rotary coupler to hold it in its central position.
2. Push the rotary coupler onto the steering column until the two clips engage.
3. Install the electrical connector (1) for the rotary coupler.
4. Install the column switches into the rotary coupler.
5. Connect the electrical connectors for the column switches.
6. Put the load-spread plate in position on the steering column.
7. Install the screw that attaches the load-spread plate.
8. If a rotary coupler is to be installed that is not new, remove the tape used to hold it in its central position.
9. For a new rotary coupler, remove the locking key.
10. Install the top and bottom steering column shrouds (Refer to ’Top and Bottom Shrouds for the Steering
Column - Remove and Install’, page 11-4-4).
11. Put the electrical cables from the rotary coupler through the steering wheel.
12. Align and install the steering wheel assembly.
13. Install and torque the M10 screw that attaches the steering wheel (Refer to ’Specifications’, page 11-6-1).
14. Connect the electrical connector for the steering wheel harness.
15. Connect the two electrical cables to the airbag module.
16. Put the airbag module in position. 17. Turn the steering wheel to get access to install one of the
two airbag module M6 attachment screws.
18. Install the first M6 attachment screw.
19. Turn the steering wheel to get access to install the second airbag module M6 attachment screw.
20. Install the second M6 attachment screw.
21. Connect the vehicle battery.
Wiper Switch for the Steering Column -
Remove and Install
Remove
1. Remove the top shroud from the steering column (Refer to ’Top Shroud for the Steering Column - Remove and
Install’, page 11-4-1).
2. Release the clips that attach the wiper switch to its mounting.
3. Release the wiper switch from its mounting.
4. Disconnect the electrical connector for the wiper switch.
5. Remove the wiper switch.
Install
1. Connect the electrical connector to the wiper switch.
2. Install the wiper switch in the mounting.
3. Make sure that the clips that attach the switch are correctly engaged.
4. Install the top shroud to the steering column (Refer to ’Top Shroud for the Steering Column - Remove and
Install’, page 11-4-1).
Caution
Align the steering wheel and the rack to the centre position during assembly. If you do not, the rotary
coupling can be damaged. Al so, it can be difficult to
align the steering wheel in the straight-ahead position.
Repair Operation Time (ROT)
ItemCode
Wiper Switch for th e Steering Column -
Remove and Install 11.06.EL

Steering Wheel (11.06)
Steering (11.00)
May 2007 Workshop Manual 11-6-1
Steering (11.00)
Steering Wheel (11.06)
Specifications
Maintenance
Steering Wheel-Renew
Remove
1. Remove the driver's airbag module (Refer to ’Driver’s Airbag Module - Remove an d Install’, page 11-6-1).
2. Turn the steering to the centre position.
3. Disconnect the vehicle battery.
4. Disconnect the electrical connector for the steering wheel harness.
Figure A11-06-1096
5. Remove the M10 Torx screw that attaches the steering wheel.
Figure A11-06-1095
6. Remove the steering wheel assembly.
7. Apply tape to hold the rotary coupler in its central position.
Installation
1. Put the electrical cables from the rotary coupler through
the steering wheel.
2. Align and install the steering wheel assembly.
3. Install and torque the M10 screw that attaches the steering wheel (Refer to ’S pecifications’, page 11-6-1).
4. Connect the electrical connector for the steering wheel harness.
5. Install the driver's airbag module (Refer to ’Driver’s Airbag Module - Remove and Install’, page 11-6-1).
6. Connect vehicle battery.
Driver’s Airbag Module - Remove and
Install
Remove
For Pre-08MY vehicles:
1. Put the key in the ignition switch and turn it to position 1 to release the Electronic Steering Column
Lock (ESCL).
Torque Figures
DescriptionNm.lb/ft
Steering Wheel Attachment Screw 40 29.5
Airbag Module Att achment Screws 9 6.6
Repair Operation Time (ROT)
Caution
Align the steering wheel and the rack to the centre position during assembly. If you do not, the rotary
coupling can be damaged. Also, it can be difficult to
align the steering wheel in the straight-ahead position.
Repair Operation Time (ROT)

Steering Wheel (11.06)
Steering (11.00)11-6-2 Workshop Manual May 2007
For 08MY vehicles or newer:
2. Put the Emotion Control Unit (ECU) into the docking station at position 2 to release the ESCL..
3. Disconnect the vehicle battery.
4. Turn the steering wheel to get access to one of the two M6 screws that attach the airbag module.
Figure A11-06-1093
5. Remove the M6 screw.
6. Turn the steering wheel to get access to the second M6 screw that attaches the airbag module.
7. Remove the second M6 screw.
8. Move the airbag module to get access to the two electrical connectors.
Figure A11-06-1094
9. Disconnect the two electrical connector for the airbag module.
10. Remove the airbag module and keep it in an approved storage area.
Install
1. Connect the two electrical cables to the airbag module.
2. Put the airbag module in position.
3. Turn the steering wheel to get access to install one of the two airbag module M6 attachment screws. 4. Install and torque the first M6 attachment screw.
5. Turn the steering wheel to get access to install the
second airbag module M6 attachment screw.
6. Install and torque the second M6 attachment screw.
7. Connect the vehicle battery.
WAR NI NG
LEAVE THE VEHICLE FOR TWO MINUTES AFTER YOU
DISCONNECT THE BATTERY BEFORE YOU DO WORK.
IF YOU DO NOT, THE AIRBAG SYSTEM CAN OPERATE AND CAUSE INJURY.

Air Conditioning (A/C) System (12.03)
Climate Control (12.00)
12-3-14 Workshop Manual May 2007
14. Recharge A/C refrigerant (see Workshop Manual
procedure 12.03.FA Refriger ant Gas - Recover/Recharge
- Renew).
15. Battery isolation switch ‘ON’.
Blower Assembly-Renew
Removal
1. Remove IP assembly (see Workshop Manual procedure 01.12.AB Facia Assembly - LHD - Remove for access
and refit).
2. Disconnect multiplugs (x2) from blower motor (see Fig. 1).
3. Release harness clip from blower motor.
4. Remove nuts (x3) securing blower motor assembly to IP.
5 . Remove bolt and nut s (x 2) s ecurin g hea ter u nit to IP (se e Fig. 2).
6. Release and remove blower motor assembly from heater unit.
Installation
1. Install blower motor assembly to heater unit. 2. Align blower motor assembly and heater unit onto studs.
3. Install and torque tighten bolt and nuts (x5) securing
heater and blower assemblies to IP.
4. Install harness clip in blower motor assembly.
5. Connect multiplugs (x2) to blower motor.
6. Install IP assembly (see Workshop Manual procedure
01.12.AB Facia Assembly - LHD - Remove for access
and refit).
Compressor to Condenser Tube
Assembly-Renew
Removal
1. Remove PAS pump (see Workshop Manual procedure 03.05.AA Pump - Power Steering - Renew).
2. Remove condenser (see Workshop Manual procedure 03.03.EC Air Con - Condenser - Renew).
3. Disconnect breather pipe qu ickfits (x2) from air cleaner
duct.
4. Remove throttle body duct for access (clips x3).
5. Disconnect sensor multip lugs (x2) (see Fig. 1).
6. Remove (bolts x2) pipe support P-clips and pipe.
7. Mark relative position of p-clips (x2), remove from pipe.
Installation
1. Install P-clips (x2) to pipe in same position as from old pipe.
2. Install pipe and (bolts x2) pipe support P-clips.
3. Connect sensor multiplugs (x2).
Repair Operation Time (ROT)
$
$
Repair Operation Time (ROT)
ItemCode
Compressor to Condenser Tube
Assembly-Renew 12.03.GA
Fig. 1
Caution
Ensure open A/C pipe ends are plugged immediately
after disconnecting refrigerat ion parts. If moist air or
foreign material enters the refrigeration cycle, cooling ability will be lowered and abnormal noise or other
faults may occur.
$

Air Conditioning (A/C) System (12.03)
Climate Control (12.00)
May 2007 Workshop Manual 12-3-15
4. Install throttle body duct.
5. Connect breather pipe quickf its (x2) to air cleaner duct.
6. Install condenser (see Workshop Manual procedure 03.03.EC Air Con - Condenser - Renew).
7. Install PAS pump (see Workshop Manual procedure 03.05.AA Pump - Powe r Steering - Renew).

Wiring and Circuit Protection (18.01)
Electric Distribution/Electronic Control (18.00)
May 2007 Workshop Manual 18-1-3
F26 20A Headlamp wash pump (HID Only)
F27 25A Spare
F28 10A Module - ABS/Key Reader and Steering angle sensors
F29 25A Spare
F30 5A Alternator battery sensing
F31 30A Heated front screen
F32 30A Wiper (slow)
F33 30A Wiper (fast)
F34 20A Heater Blower motor
F35 60A Cooling fan module
Central
Electronics
Module
Fusebox
Fuse/
RelayRatingFunction
F43 10A Multi media module display/Phone/GPS tuner/Media player
F44 10A Airbag module
F45 15A Accessory socket and illumination
F46 5A Driver Information/Master light switch/Glove box relay/Master lock switch Battery Off
switch/Boot release switch/Speaker-switch/
JBFB-R7/Centre console module/Bluetooth
module
F47 5A Interior lamps (front)/Seat switches/Fuel flap switch/glovebox switch/Rear power
illumination
F48 15A Windscreen wash pump
F49 10A Occupant detect (Driver and passenger seat)/Airbag module
F50
F51 10A Diagnostic connectors/Centre stack switches
F52 5A Start button
F53 10A Module - HID lighting
F54 10A Engine fuse box/Boot fuse box/Tyre pressure monitor module/Satellite navigation relay
F55
F56 10A Centre console module/Sounder module/
Hazard switch
F57 15A Diagnostic connectors/Brake pedal switch
F58 10A High beam (RH)
F59 10A High beam (LH)
F60 15A Drivers seat power (Heating)
F61 15A Passenger seat power (Heating)
F62 20A A/C module
F63 20A
F64 5A AM/FM receiver module/Traffic Monitoring Control module (TMC)
F65 5A Media player/Multi media module and display/Audio amplifier
F66 10A Centre console module/Infotainment control module
F67
F68
F69 5A BFB-R5
F70
F71
F72
F73
F74 15A Fuel pump
F75
F76
F77 15A Boot power socket
F78
F79 5A Reversing lamps/Module - Parking aid
F80 5A Battery ‘Off’ switch
F81 20A Ignition switch
F82 25A Passenger door module
F83 25A Driver door module
F84 25A Passenger seat power/Passenger seat switchpack
F85 25A Driver seat power/Driver seat switchpack
F86 5A Start button, Driver and passenger seats