phone ASTON MARTIN V8 VANTAGE 2010 Workshop Manual

Workshop Manual

Aston Martin Lagonda Limited
Banbury Road, Gaydon, WARWICK, Warwickshire, England, CV35 0DB
Telephone: (01926) 644700 Fax: (01926) 644733
Aston Martin are constantly seeking to improve the specificat ion, design and production of our vehicles and alterations
take place accordingly. While every effort has been made to ensu re the accuracy of this Manual, it should not be regarded
as an infallible guide to current specifications of any particular vehicle.
All rights reserved. No part of this publication may be reprod uced, stored in a retrieval system or transmitted, in any form,
electronic, mechanical, photocopying, recording or other me ans without prior written permission from Aston Martin
Lagonda Limited.
The manufacturer reserves the right to vary specifications without notice in accordance with its policy of continual product
improvement.
Produced by the Technical Publications Department Aston Martin Lagonda Limited
Issue 6 - March2010

Audio System (15.01)
Vehicle Entertainment (15.00)
May 2007 Workshop Manual 15-1-5
10. Remove screws (x8) secu ring centre stack support
bracket, remove bracket (see Fig. 3).
11. Remove ICM interface driver.
12. Remove screws (x2) securi ng clock unit, remove clock
unit (see Fig. 4).
13. Remove screws (x2) secu ring telephone switchpack,
remove switchpack.
14. Remove screws (x2) secu ring satellite navigation
switchpack, remove switchpack.
Installation
1. Install satellite navigation switchpack, install and tighten screws (x2).
2. Install telephone switchpack, install and tighten screws (x2).
3. Install clock unit, install and tighten screws (x2). 4. Install ICM interface driver,
install centre stack support
bracket, install and tighten screws (x8).
5. Install HVAC unit, install an d tighten screws (x6). Install
control knobs (x3), connect multiplugs (x2).
6. Install rear fog guard switch and secure with clips.
7. Install IDV switch and secure with clips.
8. Install hazard warning switch and secure with clips.
9. Install A/C re-circulation switch and secure with clips.
10. Install A/C request switch and secure with clips.
11. Install centre stack assembly (see Workshop Manual procedure 15.01.CB Centre Stack Assembly - Remove
for Access and Refit).
GPS Tuner-Renew
1. Remove RH rear wheel arch liner (see Workshop Manual procedure 01.02.HB Wheel Arch Liner - Rear -
RH - Renew).
2. Remove bolts (x4) from tuner base plate to wheel arch (see Fig. 1).
Fig. 3
Fig. 4$$
$
Repair Operation Time (ROT)

Wiring and Circuit Protection (18.01)
Electric Distribution/Electronic Control (18.00)
May 2007 Workshop Manual 18-1-3
F26 20A Headlamp wash pump (HID Only)
F27 25A Spare
F28 10A Module - ABS/Key Reader and Steering angle sensors
F29 25A Spare
F30 5A Alternator battery sensing
F31 30A Heated front screen
F32 30A Wiper (slow)
F33 30A Wiper (fast)
F34 20A Heater Blower motor
F35 60A Cooling fan module
Central
Electronics
Module
Fusebox
Fuse/
RelayRatingFunction
F43 10A Multi media module display/Phone/GPS tuner/Media player
F44 10A Airbag module
F45 15A Accessory socket and illumination
F46 5A Driver Information/Master light switch/Glove box relay/Master lock switch Battery Off
switch/Boot release switch/Speaker-switch/
JBFB-R7/Centre console module/Bluetooth
module
F47 5A Interior lamps (front)/Seat switches/Fuel flap switch/glovebox switch/Rear power
illumination
F48 15A Windscreen wash pump
F49 10A Occupant detect (Driver and passenger seat)/Airbag module
F50
F51 10A Diagnostic connectors/Centre stack switches
F52 5A Start button
F53 10A Module - HID lighting
F54 10A Engine fuse box/Boot fuse box/Tyre pressure monitor module/Satellite navigation relay
F55
F56 10A Centre console module/Sounder module/
Hazard switch
F57 15A Diagnostic connectors/Brake pedal switch
F58 10A High beam (RH)
F59 10A High beam (LH)
F60 15A Drivers seat power (Heating)
F61 15A Passenger seat power (Heating)
F62 20A A/C module
F63 20A
F64 5A AM/FM receiver module/Traffic Monitoring Control module (TMC)
F65 5A Media player/Multi media module and display/Audio amplifier
F66 10A Centre console module/Infotainment control module
F67
F68
F69 5A BFB-R5
F70
F71
F72
F73
F74 15A Fuel pump
F75
F76
F77 15A Boot power socket
F78
F79 5A Reversing lamps/Module - Parking aid
F80 5A Battery ‘Off’ switch
F81 20A Ignition switch
F82 25A Passenger door module
F83 25A Driver door module
F84 25A Passenger seat power/Passenger seat switchpack
F85 25A Driver seat power/Driver seat switchpack
F86 5A Start button, Driver and passenger seats

Vehicle Control System (18.08)
Electric Distribution/Electronic Control (18.00)
18-2-2 Workshop Manual May 2007
Module Locations
1A Central Electronic Module (CEM) LH D15BInstrument Cluster Module LHD
1B Central Electronic Module (CEM) RH D 16 Navigation Display Module RHD/LHD
2A Driver’s Door Module RHD 17 Yaw Rate Sensor Module RHD/LHD
2B Driver’s Door Module LHD 1 8Restraint Module RHD/LHD
3A Passenger Door Module LHD 19 AM/FM Tuner Module RHD/LHD
3B Passenger Door Module RHD 20 Traffic Messaging Channel (TMC) Module RHD/
LHD
4 Fuel Pump Module RHD/LHD 21 GPS Tuner Module RHD/LHD
5 Parking Aid Module RHD/LHD 22 Amplifier Module RHD/LHD
6 Remote Key Entry Module RHD/LH D23Amplifier Module RHD/LHD
7 Security Microwave RHD/LHD 24A Powe rtrain Control Module (PCM) LHD
8A Tyre Pressure Monitor Module LHD 24B Powertrain Control Module (PCM) RHD
8B Tyre Pressure Monitor Module RHD 25A Telephone (GSM) Module LHD
9Multi-media Module (MMM) RHD/LHD 25B Teleph one (GSM) Module RHD
10 ABS/Traction Control/Dy namic Stability Control
(DSC) Module RHD/LHD 26A Telephone (Bluetooth) Module LHD
11 Tracker Module RHD Only 26B Tel ephone (Bluetooth) Module RHD
12 Fan Module RHD/LHD 27A High Intensity Discharge (HID) Module LHD
13 HVAC Module RHD/LHD 27B High Intensity Discharge (HID) Module RHD
14 Infotainment Control Module RHD/ LHD 28 Centre Console Module (CCM)
15A Instrument Cluster Module RHD

Electronics Training Programme
CONTENTS

INTRODUCTION 7
Description 9
SYSTEM LAYOUT 11
V8 Vantage Layout 11
DB9 Layout 13
INPUTS 15
V8 Vantage Power Supplies 15
DB9 Power Supplies 15
V8 Vantage Signal Inputs 15
DB9 Signal Inputs 15
Screens 15
OUTPUTS 17
V8 Vantage Outputs to Amplifier 17
DB9 Outputs To Amplifier 17
LED Indicator Outputs 17
SYSTEM OPERATION 19
Controls 19
Getting Help 21
Connecting A Phone 21
Selecting a Phone 22
List Paired Phones 22
Removing A Paired Phone 22
Removing All Phones 22
Making Calls 23
Answering Incoming Calls 25
Ending Calls 25
Transfer A Call 25
Rejecting A Call 25
Mute A Call 26
Un-mute A Call 26
Call Waiting 26
Touch-Tone System 26
Bluetooth Contact List 27
Switching Voice Prompts On/Off 28
Selecting A Language 28
DIAGNOSTICS 31
V8 Vantage Connector Pin Allocation 31
DB9 Connector Pin Allocation 32
Troubleshooting 33
V8 Vantage Wiring Diagrams 35
DB9 Wiring Diagrams 39

APPENDIX 1
APPENDIX 2

5

Electronics Training Programme
Description
The Bluetooth Module controls the Bluetooth system on all cars. This module is a stand-alone unit,
which is not connected to any communication network on the car. The module is located on the
drivers side of the Instrument Pack (IP) ju st above the pedals (see page opposite).

The components of the system are:
1. Microphone
2. Bluetooth switches (steering wheel)
3. LED Indicator
4. Bluetooth Module
5. Amplifier (audio)
6. Switcher box (V8 Vantage only)

If a DB9 is installed with both the ‘in-car’ ph one and the Bluetooth systems and both systems are
active then the Bluetooth system will override the ‘i n-car’ phone system. An active call on the ‘in-car’
phone will be ended if a call is re ceived on the Bluetooth system or any of the Bluetooth menus are
used.

The Bluetooth module has been designed to meet the following parameters:
Parameter Units Nominal Lower Limit Upper Limit
Battery Voltage Volts N/A 10.5 16.0
Nominal Voltage Volts 13.2 12.2 14.2
Over Voltage (for 1 minute) Volts 24.0 18.0 25.0
Operating Current mA 225-300 <300uA (sleep) <1.5A
Room Temperature °C 25 15 35
Operating Temperature °C N/A -30 70
Storage Temperature °C N/A -40 85


9

Electronics Training Programme
SYSTEM LAYOUT
V8 Vantage Layout
Bluetooth enabled and
paired phone
Bluetooth receiver module
Amplifier module
LED Indicator (Bluetooth display module)
Front speaker Switcher box
Microphone Steering column control
switches
Power Supply

Door speaker (drivers side) Door speaker
(passenger side)

11

Electronics Training Programme
DB9 Layout
Bluetooth enabled and
paired phone
Bluetooth receiver module
Microphone
Amplifier module
Power Supply
Steering column control switches
LED Indicator (Bluetooth display module)
Door speaker (drivers side) Door speaker
(passenger side)

13

Electronics Training Programme
INPUTS
The Bluetooth system relies on a number of signals it receives either from the car (via hard wiring) or
the users phone (via wireless Bluetooth communication network).

The Bluetooth system will only function if the us ers mobile phone has Bluetooth enabled and it is
‘paired’ to the car. For more information refer to the user’s guide for your mobile phone.

V8 Vantage Power Supplies
Description Supplied From Source Protection
Wakeup signal Central Electronic Module Comfort Relay F68 (5 Amp)
Power supply 1 Central Electronic Module Interior Lights Relay F46 (5Amp)
Power supply 2 Central Electronic Module Interior Lights Relay F46 (5Amp)

DB9 Power Supplies
Description Supplied From Source Protection
Wakeup signal Central Electronic Module Comfort Relay F69 (5 Amp)
Power supply 1 Central Electronic Module Interior Lights Relay F46 (5Amp)
Power supply 2 Central Electronic Module Interior Lights Relay F46 (5Amp)

V8 Vantage Signal Inputs
Input Description Signal Characteristic
MIC In Input signal from microphone Varying current signal direct from microphone
Keypad Steering wheel controls input Variable resistance to earth signal

DB9 Signal Inputs
Input Description Signal Characteristic
MIC In + Input signal from microphone Varying current signal supplied via amplifier
MIC In - Input signal from microphone Varying current signal supplied via amplifier
Keypad Steering wheel controls inpu t Variable resistance to earth

Screens
Some of the signals in and out of the Bluetooth modu le require screening to avoid interference being
picked up. A signal screen is a single wire running along side t he signal wire(s) which will absorb
electro magnetic interference (EMI).

The Bluetooth module on the V8 Vantage features only one screen so as to protect the signal from the
microphone. This screen wire is simply an earth but it is also used as a datum from which to reference
the microphone signal.

The Bluetooth module used on DB9’s features two screens. One is as on the V8 Vantage but is used
only as a screen (because the microphone signal from the amplifie r has two signal wires) and no
datum is required. The second screen on the module is used to screen the ‘Lineout’ signals to the
amplifier. As with the microphone scr een this wire is connected to earth.

15

Electronics Training Programme
OUTPUTS
V8 Vantage Outputs To Amplifier
The Bluetooth module in the V8 Vantage has three outputs sent directly to t he audio amplifier. These
outputs are:
1. Radio mute.
2. Speaker +
3. Speaker –

DB9 Outputs To Amplifier
As with the Bluetooth module in the V8 Vantage, the DB9 Bluetooth module has three outputs it
sends directly to the audio amplifie r. It should be remembered that all DB9’s feature a Linn amplifier
and therefore the Bluetooth output requir ements are different. These outputs are:
1. Radio mute.
2. Lineout -
3. Lineout +

The combination of these three signals allows the Linn Amplifier to control the audio output and
phone output through all or some of the speakers.

LED Indicator Outputs
The DB9 and V8 Vantage use the same LED Indicator (Bluetooth display) controlled in the same way
by the Bluetooth module. The output s from the Bluetooth module are:
• UIM LED - For Active Call LED (amber)
• UIM LED - For Active Call LED (blue)

These two outputs individually control the status LED’s (amber and blue) earth signal therefore
switching the LED’s on and off independently.


17