AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual

AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual A3 1995 8L / 1.G AUDI AUDI https://www.carmanualsonline.info/img/6/947/w960_947-0.png AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual

Page 1 of 8

AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual 13-46
 
  
Crankshaft, removing and 
installing Note:  
For engine disassembly and assembly, mount 
engine to an assembly stand using VW540 holding 
fixture. 
1 - 
Main bearing shells 1, 2, 4 and 5 
I

Page 2 of 8

AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual 13-47
 
  
4 - 
Main bearing shell 3 
Install shell without lubrication groove in 
main bearing cap Install shell with lubrication groove in 
cylinder block Do not interchange used main bearing 
shell

Page 3 of 8

AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual 13-48
 
  
8 - 
Needle bearing 
Removing and installing   Page 13
-50
9 - 
Crankshaft 
Axial play when new: 0.07-0.23 mm (0.003-
0.009 in.) Wear limit: 0.30 mm (0.012 in.)
 - Radial clearance is measu

Page 4 of 8

AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual 13-49
 
    
Note: 
Tightening torque   Fig. 1  Removing and installing sensor wheel
-  Always replace sensor wheel -2- when screws -1- are removed.
After tightening a second time, the attachment poin

Page 5 of 8

AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual 13-50
      
Crankshaft needle bearing, removing 
and installing
 
     
Note:  
     
A pilot needle bearing must be installed in the 
crankshaft of engines for vehicles with manual 
transmission. In

Page 6 of 8

AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual     
-  Pull out using puller -A-, e.g. 21/2 Kukko extractor and 22/1 Kukko 
support or 10-202 puller. 
Pa
ge 6 of 8 Crankshaft, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servle

Page 7 of 8

AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual 13-51
      
Installing  
    
-  Drive in using VW207C drift and/or 3176 centering mandrel.
   When needle bearing is installed, side with inscription must be visible.
    
Installation of needle bea

Page 8 of 8

AUDI A3 1995 8L / 1.G AEB ATW Engines Crankshaft Workshop Manual 13-52
 Crankshaft dimensions  Reconditioning dimension  
  Crankshaft journal diameter - mm (in.)  
Connecting rod journal diameter - mm (in.)  
        
maximum size (from nominal)   -0.017 (0.0007)