lock AUDI A3 2016 Owner´s Manual

Lights and Vision
Instrument illumination
The brightness of the instrument cluster and the
center console can be adjusted .
Fig. 37 Instrument ill umination
Requirement: the light must be switched on.
~ Press the knob to release it .
~ Turn the knob toward"-" or"+" to reduce or in­
crease the brightness.
~ Press the knob again to return it to its original
position.
(D Tips
The needles and gauges in the instrument cluster illuminate when the headlights are off
and the ignition is switched one. The illumina­
tion reduces automatically and eventually
turns off as brightness outside decreases.
This function reminds the driver to turn the
headlights on at the appropriate time.
Vision
Adjusting the exterior mirrors
Fig. 38 Driver's door: knob for the ex ter ior mirrors (exam­
ple)
Turn the knob to the desired position:
50
0 - All adjustment functions are deactivated.
q;p -adjusting the left/right exterior mirror.
Move the knob in the desired direction.
4#1 -Heating* the mirror glass depending on the
outside temperature.
8 -Folding exterior mirrors*. You can select if
the mirrors fold in automatically when you lock
the vehicle In the
MMI* ~ page 40.
Front passenger's exterior mirror tilt
function*
To help you see the curb when backing into a
parking space, the surface of the mirror tilts
slightly. For this to happen, the knob must be in
the position for the front passenger's outside mirror.
You can adjust the tilted mirror surface by turn­ ing the knob in the desired direction . When you
move out of reverse and into another gear, the
new mirror position is stored and assigned to the
key you are using.
The mirror goes back into its original position
once you drive forward faster than 9 mph (15 km/h) or turn the ignition off.
.&, WARNING
Curved mirror surfaces (convex) enlarge the
field of vision. However, they make objects in the mirror appear smaller and further away.
Your may estimate incorrectly when you use
these mirrors to gauge your distance from the
vehicles behind you when changing lanes -ac­
cident risk!
(D Note
- Applies to vehicles with power folding out­
side mirrors*: if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must use the pow­ er folding function to fold the mirror all the
way out. You will hear a loud noise when the
mirrors are latched back in place. The mirror
housing must not be moved back into place
by hand because this would impair the func­
tion of the mirror mechanism.
-

Lights and Vision
Wiper service position /blade replacement
po sit ion
.. To bring the wipers into the service position,
turn the ignition
off and move the windshield
wiper lever into position@¢
page 52, fig. 41 .
.. To bring the wipers into the starting pos it ion,
turn the ignition on and move the windsh ield
wipe r lever into position@¢
page 52, fig. 41.
Removing th e wiper blade
.. Fo ld the windshield wiper arm away from the
winds hield.
.. Press the lock ing knob
(D ¢ fig. 43 on the wiper
blade . Hold the w iper blade firmly .
.. Remove the wipe r blade in the direct ion of the
arrow.
Installing th e wiper blade
.. Insert the new wiper b lade into the mount on
the wiper arm @unti l you hea r it latch into
place .
.. Place the w ipe r arm back on t he w indshie ld .
.. Turn the serv ice position off.
_& WARNING
F or safety re asons, t he wind shie ld wiper
blades sho uld be replaced once or twice each
year .
- T he wi ndshield wipe rs mus t only be folded
away w hen in the serv ice posi tion. Other ­
wise, you r is k damaging the paint on the
hood or the windshield wiper motor .
- You should not dr ive your ve hicle or press
the windshie ld wiper lever when the wiper
a rms are fo lded away from the windshield.
The windshield wipers would move back in­
to the ir o rig inal position and could damage
the hood and w indshield.
- To prevent damage to t he windshie ld wash­
er system, a lways loosen wiper blades that
have frozen to the w indshield before turn­
i ng the wipers on .
- To preve nt damage to the wiper b lades, do
not apply gasol ine, pet roleum, thinning
54 agents o
r othe r solvents on the wi per
blades or near them .
- T o prevent damage to the wiper arms or
other components, do not try to move the
windshield wipe rs by hand.
@ Tips
- C ommercial hot wax s uch a s the types used
by car washes make it more diffic ult to
clean the w indshie ld .
- You can also use the service pos it ion, for ex ­
amp le, if you want to protect the winds hield
from icing by using a cover.
- You cannot activate the service posit ion
when the hood is open .
Replacing rear windshield wiper blade
Applies to vehicles: with rear window wiper (A3 Sportback)
Fig.
44 Rear win dow w ipe r: remov ing t he wipe r blade
Removing the wiper blade
.. Fold the w indshie ld w iper arm aw ay from the
rear wi ndow.
.. Ho ld the wiper blade below the center -arrow ­
¢
fig. 44 and pull it o ut of the reta iner. Hold
the windshield wiper a rm secure ly while doing
this.
Installing the w iper blade
.. Press the wipe r blade mount into the re tainer.
Securely hold the w iper arm at the upper p las ­
tic end .
.. Fold the rear window wiper arm back onto the
w indshield. .,..

Seats and storage
Rear center armrest
Applies to vehicles: with rear center armrest
The storage compartment and cup holder are in­
tegrated in the armrest.
Fig. SO Rear a rmrest
Folding the armrest down
• Tilt the armrest all the way down.
Opening the storage compartment
• Lift the cover on the upper rim.
~I
gl
~
For more information on the use of the cup hold­
ers , see ¢
page 62 .
Head restraints
Front head restraints
Applies to veh icles: with adjustable head restraints
-
'
' F ig. 51 Front seat: adjust ing the head restra int
Applies to vehicles w ith super sport seats* (not
pictured): the head restraint is integ rated in the
backrest and is therefore not adjustable
Adjust the head restra ints so the upper edge is as
even as possible with the top of your head. If that
is not possible, try to adjust as close to this posi­
tion as possible . Push the head restraint as close
as poss ible to the back of the head.
60
• To move the head restra int up or forward, slide
it unti l it locks into place.
• To move the head restra int down or back, press
the side button -arrow-¢
fig. 51 and slide the
head restraint until it locks into place.
Refer to ¢
page 170, Proper adjustment of head
restraints
for guidelines on how to adjust the
height of the front head restraints to suit the oc­
cupant's body size.
A WARNING
- Dr iving without head restra ints or head re­
stra ints that are not adjusted correctly dra­
matically increases the risk of serious or fa­
tal nec k injuries.
- Read and following the WARNINGS in
¢ page 170, Proper adjustment of head re­
straints.
@ Tips
Head restraints that are adjusted correctly
and safety belts are an extremely effective
combination of safety equipment.
Rear head restraints
ro -0
Fig. 52 Outer rea r head restra ints : re lease point
- 0 > :g
If there are passengers in the rear seat, fold the
head restraints up on the occ upied seats at least
to the next notch ¢
,& .
Adjusting the head restraints
• To move the head restra int up, hold it at the
sides with both hands and slide it upward until
you feel it click into place . .,.

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
A WARNING
Spilled hot liquid can increase the risk of acci­
dents and injuries.
- Never drive with containers that contain hot
liquid such as coffee or tea. The hot liquid
could spill and cause burns during a colli­
sion, sudden braking or other vehicle move­
ment. Spilled hot liquid can also increase
the risk of accidents and injuries.
- Only use soft containers in the cup holders .
Hard cups and glasses can increase the risk
of injury during a collision.
- Never use the cup holder or the adapter as
an ashtray - this is a fire hazard.
(D Note
Beverage containers in the cup holders should
always have a lid . Otherwise, beverages could
spill and cause damage to vehicle equipment
or stain the seat covers.
Glove compartment
Fig. 58 Glove compartmen t
Opening/closing
.. To open the glove compartment, pull the han­
dle in the direction of the arrow.
.. To close the glove compartment , swing the lid
upward until it clicks into place .
The glove compartment can be locked using the
vehicle key .
A WARNING
Always leave the lid on the glove compart­
ment cover closed while driving to reduce the
risk of injury.
Seats and storage
Additional storage compartments
There are additional storage compartments,
compartments and holders at other locations in
the vehicle:
- In the upper part of the glove compartment.
- In the center console under the center arm -
rest* .
- On the back of the right front seat . The com­
partment* can hold a maximum weight of 2 lbs
(1 kg) .
- Garment hooks on the B -pillar
c:> ,& .
A WARNING ,~ -- Do not place any objects on the instrument
panel. Objects that are not stored securely
can slide around in the vehicle while driving ,
when accelerating or braking or when turn­
ing.
- Make sure that objects cannot fall out of the
center console storage compartment or oth­
er compartments and into the footwell
while driving. These objects could prevent
you from braking or accelerating during
sudden braking maneuvers.
- Garments hung on the hooks must not ob­
struct the driver's view . The garment hooks
are only designed for light objects. Do not hang any garments with hard, sharp or
heavy objects in the pockets on the garment
hooks . These objects could injure vehicle oc­
cupants during sudden braking or in a colli­
sion -especially if the airbags deploy .
-Always keep the glove compartment closed
while driving to reduce the risk of injury dur­
ing a collision or heavy braking .
- Read and following the WARNINGS in
¢ page 204, Important safety instructions
on the side airbag system.
- Hang garments so that they do not obstruct
the driver's view .
- The garment hooks should only be used for
light articles of clothing. Do not leave any
heavy or sharp-edged objects in the pockets
that could interfere with the side airbags
unfolding and cause injuries in the event of
a collision.
63

Installing
• Slide the cover@ hor izontally into the desig­
nated ho lder @in the side bracket until the
cover is lined up.
• Hook the straps into the l uggage compartment
lid @ ¢
A.
A WARNING
-To prevent accidents, never install the lug­
gage compartment cove r unsec ured.
- The luggage compartment cover is not a
surface for storing objects. Objects placed
on the cover increase the r isk of injury to all
vehicle occupa nts dur ing sudden bra king
mane uvers o r when i nvo lved in an accident .
Increasing the size of the luggage
compartment
-
The rear seat backre sts can be folded forward ei ­
ther separately or together.
F ig. 61 Backrest: re lease lever (le ft s ide, examp le)
Folding the backr est forward
• Push the corresponding head restraint down­
ward
¢ page 60.
• Press the release lever @ in the direct ion of the
arrow .
• Fold the backrest forward .
Folding the backrest back into the upright
position
• Fold the backrest down until it latches secure ly
¢ ,& .When you can no longer see the red mark
;::: on the pin @, the seat is la tched .
0 > CX)
rl I.Cl U"I
rl I.Cl rl
Seats and storag e
A WARNING
-~
-The backrest must be latched securely to
e nsu re that the safety belt is p rotecti ng the
center seating position .
- The bac krest must be securely latched so
objects cannot slide fo rward out of the lug­
gage compartment during sudde n braking .
- Always make su re the backrest is latched
completely by pull ing fo rwa rd on it .
- Make sure the safety belt is not caught in
the door hinges or the seat fittings and
damaged.
- To rn or frayed safety be lts can break, and
be lt anchors can b reak dur ing a col lision .
C heck the safety be lts regu la rly. Safety
be lts wi th noticeable damage to the we b­
b in g, b indings, bu ckles or ret ra cto rs m ust
be repla ced.
(D Note
- If you move the front seat back when the
rear seat backrest is fo lded fo rwa rd, yo u
c o ul d d am age the head restra in ts on t he
rear sea t. If necessary, remove the rear sea t
head restraint be fore mov ing the front seat
back
- Make sure the sa fe ty belt is not pinche d in
the back rest lock a nd damage d when the
rear seat backrest if folded back . Othe r ob­
jects should be removed from the rear
bench seat to protect the rear backrest from
damage .
65

Driving
-Always hold the steering wheel with your
hands in the 9 o'clock and 3 o'clock posi­
t ions to reduce the risk of injury if the airbag
deploys.
- Never hold the steer ing whee l in the
12
o'clock posit ion or with both hands on the
rim or the center of the steer ing whee l.
Holding the steering wheel inco rrectly s ig­
nificantly incr eas es the risk of inju ry to the
h ands, arms and head if t he ai rbag dep loys.
Starting and stopping
the engine (vehicles with
an ignition Lock)
Starting the engine with the key
A pp lies to veh icles: w ith ig ni tion lock
The ignition is switched on and the engine start­
ed with the key in the ignition .
Fig . 77 Ign it io n key pos it ions
Stee ring lock
If the steering whee l w ill not turn, the steering
lock is engaged .
.,. To release the steering wheel lo ck, inse rt the
k ey i n the ignition lock and tu rn t he key in the
-d irection of the arrow- while tu rning the steer­
ing wheel.
Sw itching the ignition on/off or preheating
.,. To switc h the ignition on, turn the ign ition key
to posit io n @ . The need le in the tachometer
moves into the
READY position.
.,. To switc h the ign ition off, turn the ignit ion key
to position @. The need le in the tachometer
moves into the
OFF position.
80
D iesel ve hicl es are p reheated while the ig nition is
switched on
m .
Starting the engine
You r vehicle is equipped wi th la unch control. As
soon as you have turned the ig nition key to pos i­
tion @, the eng ine will start au tomati cally .
.,. Press the brake pedal and move the sele ctor
lever to the P o r
N position.
.,. Turn the key briefly to pos it ion @. The ign ition
key a utomat ically returns to position @. D o not
press the acce lerator peda l when doing this.
Major elec trical equipmen t sw itches off tempora­
r ily whe n starting the engine.
It is possible t hat there will be a s ligh t de lay
whe n starting the engine in diesel veh icles in
colder temperatu res. Therefore, yo u must hold
t h e b rake pedal down until the eng ine starts . T he
i ndicato r ligh t turns on wh ile the engine is pre­
heating
iJ.
The preheating time depends on the coolant
temper ature and o utside temperature. The glow
pl ug indi cato r light
m will only tu rn on for ap­
proximately
1 second when the engine is warm or
t h e outside temperat ure is higher than
8 °C. That
means you can start the engine
immediately.
I f the engine does not s tart immedia tely, s top
the starti ng p rocedure by tu rni ng the ig nition key
to posit ion @ and repeat after
30 seconds .
Automatic start malfunction
There is an a utom atic st art ma lf u nct ion if the ~
(ga so lin e engine) or
m (diese l eng ine) indica tor
li ght tur ns on and the message
Engine start sys·
tem malfun ction! Please contact Service
ap ­
pears.
To star t the engine, hold the igni tion key in pos i­
tion @unt il the engine r uns.
D rive to an au thori zed A udi dealer or au thori zed
A udi Se rvice Fa cility immed iate ly to h ave the
malfunc tion correc ted .
& WARNING
- To red uce the r isk o f po ison ing, never allow
the engine to run in conf ined spaces .

,....,
N
0 > co ,...., -Never remove the ignition key from the igni­
tion look while the vehicle is moving . Other­
wise the steering lock will engage and you
will not be able to steer the vehicle .
- Please note that the brake booster and pow­
er steering only work when the engine is
running . When the engine off, you must use
more force to steer or brake the vehicle. Be­
cause the usual steering and braking capa­
bility is not available, the risk of accidents or
injuries increases.
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time. This applies particularly when chil­
dren remain in the vehicle. Otherwise the
children could start the engine or operate
electrical equipment such as power win­
dows .
- Avoid high engine speed, full throttle, and
heavy engine load as long as the engine has
not reached operating temperature yet . You
could damage th@ engine.
-The engine cannot be started by pushing or
towing .
@ For the sake of the environment
Do not let the engine run while parked to
warm up. Begin driving immediately. This re­
duces unnecessary emissions.
(D Tips
- If it is difficult to turn the key to position
(D, turn the steering wheel back and forth
slightly to release the steering wheel lock .
- Some noise after starting the engine is nor­
mal and is no cause for concern.
- If the battery is disconnected and recon­
nected, you have to hold the ignition key in
position
(D for five seconds for the engine
to start.
- After switching the ignition off, you can only
remove the key when the selector lever is in
the "P" (Park) position. After that, the selec­
tor lever is locked.
Driving
Stopping the engine with the key
App lies to vehicles : wi th ignition lock
Stopping the engine
.,. Bring the vehicle to a full stop.
.,. Turn the key to position @. The needle in the
tachometer moves into the
OFF position.
Releasing the steering lock
Requirement: the selector lever must be in P.
.,. Remove the ignition key in position @
¢ page 82, fig. 78 ¢ .&_.
.,. Turn the steering wheel until you hear the
steering wheel lock .
The locked steering helps prevent vehicle theft.
A WARNING
.--
- Never turn off the engine before the vehicle
has come to a complete stop . The full func­
tion of the brake booster and the power
steering is not guaranteed. You must use
more force to turn or brake if. Because you
cannot steer and brake as you usually
would, this could lead to accidents and seri­
ous injuries.
- Never remove the ignition key from the igni­
tion look while the vehicle is moving. Other­
wise, the steering lock could suddenly en­
gage and you would not be able to steer the
vehicle.
- Please note that the brake booster and pow­
er steering only work when the engine is
running. When the engine off, you must use
more force to steer or brake the vehicle. Be­
cause the usual steering and braking capa­
bility is not available, the risk of accidents or
injuries increases .
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time. This applies particularly when chil­
dren remain in the vehicle. Otherwise the
children could start the engine or operate
electrical equipment such as power win­
dows.
- For safety reasons, always park the vehicle
with the selector lever in the P position.
81

Driving
Otherwise, there is the r isk that the vehicle
could roll.
- After the engine has been switche d off, the
radiator fan can continue to run for up to 10
minutes - even with the ign ition switched
off . It ca n also switch on again after some
t i me if the coolant tern perature rises as the
resul t of heat buildup or if the engine co m­
partment is heat ed by the su n's rays and the
eng ine is ho t.
(D Note
- If t he engine has been unde r heavy load for
an extended pe riod of time, heat builds up
i n the eng ine compartment after the eng in e
i s sw itche d off- the re is a risk of dam ag ing
the engi ne . Fo r thi s reaso n, let the e ng ine
run for at id le for approxim ately two mi ­
nutes befo re sh utting it off .
Starting and stopping
the engine (vehicles with
a convenience key)
Engine with the
button Starting
App lies to vehicles: w ith conve nien ce key
The I START ENGINE STOP I button switches the
igni tion on and s tar ts the engine.
F ig . 78 Cente r conso le : STAR T ENGIN E ST OP butto n (w ith
co nve nience key)
You can start yo ur car w ithout using your conven­
ience key . You must simp ly be c arrying the key
with you .
Plug-in hybrid drive* : refer to the informatio n for
starting the vehicle under ¢
page 100.
82
Switching the ignition on /off or preheating
If thP 'Tij ind icator lig ht blinks and the mess age
Plea se move steerin g wheel appears when
switching the ignition on, the stee ring is locked
by the steer ing lock . In th is case, turn the steer­
i ng wheel slightly to the left/right.
.,. To switch the ignit ion on or off, press t he
I STAR T ENGINE STOPI button . Do not press the
brake pedal while doing this .
The need le in the t achome ter moves to
READY
whe n the ignition switches on an d moves to OFF
when the ignition switches off .
D iesel ve hicles are p rehea te d while the ig nition is
switched on
Iii .
Starting the engine
Your vehicle is equipped with la unch control. The
engine starts a utomat ica lly when you press the
I START E N GIN E STOP ! button br iefly.
.,. Press the brake pedal and move the selector
lever to the P or N position .
.,. Press the
I START E NGINE STOP ! button briefly .
T he engine w ill sta rt.
Major elect rical equipment sw itches off tempora­
rily whe n starting the eng ine .
It is possible that there will be a s light de lay
when starting the engine in d iesel veh icles in
colder temperatures . Therefore, you must hold
the b rake pedal down until the eng ine starts . Th e
i ndica to r light turns on wh ile the engi ne is pre­
hea ting
Iii .
The preheating t ime depends o n the coolant
temperat ure and outside temperature . The glow
pl ug indica to r li ght
II will only tu rn on for ap­
prox im ately 1 se co nd when the engi ne is warm o r
t h e ou ts ide temperat ure is higher th an 8
°C. Tha t
me ans you can s tart t he engine
immedia tely .
If th e engine does not start immediately, stop
th e starti ng p ro cedure by pushi ng the
I S TAR T EN GINE ST OP ! button ag ain an d repe at
a ft er 30 seconds. ..,.

,....,
N
0 > co ,...., Automatic start malfunction
There is an automatic start malfunction if the~
(gasoline engine) or
II (diesel engine) indicator
light turns on and the message
Engine start sys­
tem malfunction! Please contact Service
ap­
pears.
To start the engine, press and hold the
I S TART ENGINE STOPI button until the engine
runs.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
& WARNING
- To reduce the risk of poisoning, never allow
the engine to run in confined spaces.
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time. This applies particularly when chil­
dren remain in the vehicle. Otherwise the
children could start the engine or operate
electrical equipment such as power win­
dows .
- Please note that the brake booster and pow­
er steering only work when the engine is
running . When the engine off, you must use
more force to steer or brake the vehicle. Be­
cause the usual steering and braking capa­
bility is not available, the risk of accidents or
injuries increases.
(D Note
- Avoid high engine speed, full throttle, and
heavy engine load as long as the engine has
not reached operating temperature yet. You
could damage the engine.
- The engine cannot be started by pushing or
towing.
@) For the sake of the environment
Do not let the engine run while parked to
warm up. Begin driving immediately. This re­
duces unnecessary emissions.
,....,
Driving
{!) Tips
-Some noise after starting the engine is nor­
mal and is no cause for concern.
- If the . indicator light blinks in the instru­
ment cluster before switching the ignition
off, the ignition will not switch on again.
¢page 162
-If you leave your vehicle with the ignition
switched on, the ignition will switch off af­
ter a certain amount of time. Make sure that electrical equipment such as the exterior
lights are switched off .
Turning the engine off using the
button
Applies to vehicles: with convenience key
Plug-in hybrid drive*: refer to the information un­
der
¢ page 100.
"' Bring the vehicle to a full stop.
"' Move the selector lever into the P position.
.. Press the
!STAR T ENGINE STOP ! button
¢ page 82, fig. 78.
The needle in the tachometer moves to OFF when
the ignition switches off.
Steering lock1
)
The steering locks when you turn the engine off
using the
I START ENGINE STOPI* button, move
the selector lever into the P position and open
the driver's door.
The locked steering helps prevent vehicle theft.
Emergency off function
If it is absolutely necessary, the engine can also
be turned off while driving at speeds lower than
6 mph (10 km/h). To switch the engine off, press
the
I START ENGINE STOPI button twice in a row
briefly or press and hold for longer than two sec -
onds. ..,.
83

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
This message appears and a warning tone sounds if you open the driver's door when the ignition is
switched on. Switch the ign ition off so that the
battery will not d ischarge.
Pressing start/stop button again will switch off
engine!
This message appears when you press the
ISTART ENGINE STOPI* button while driving
¢ page 83, Emergency off function.
Engine start system malfunction. Please con­
tact Service
The engine automatic start system has a mal­
function . Drive to an author ized Audi dealer or
author ized Audi Service Facility immediate ly to
have the malf uncti on corrected. To start the en­
g ine, press and hold the
!START ENGINE STOPI
button.
DJ Key not recognized. See owner's manual
This message appears if there is no convenience
key inside the vehicle or if the system does not
recognize the key. The conven ience key may not
be recognized, for example, if it is covered by an
object that
disrupts the signal (such as a brief­
case), o r if the key battery is weak. Electronic de­
vices such as cell phones can also interfere with
the signal.
To still be able to start or stop the engine, refer
to "Cor rect ing a malfunction" ¢
page 84.
Ill Key not in vehicle?
The Ill indicator light turns on and this message
appears if the convenience key was removed from
the vehicle when the eng ine was running . If the
conven ience key is no longer in the vehicle, you
cannot switch the ignition on o r start the engine
once yo u stop it. In addition, you cannot lock the
ve hicl e from the outside .
Press brake pedal
This message appears if you do not press the
brake pedal when starting the eng ine .
Please engage N or P
This message appears when starting or s topping
the engine if the selector lever is not in the Nor P
position . The engine will not start/stop .
Driving
Shift to P, vehicle can roll away . Doors can only
be locked in P
T his message appears for safety reasons along
with a warning tone. It appears if the selec to r
lever for the automat ic transmission is not in the
P position when switching the ignition off with
the
I START ENGINE STOPI * button. Shift these­
lector lever to the P position. Otherwise, the vehi­
cle could roll. You also cannot lock the vehicle us­
ing the locking sensor o n the door hand le or us ­
ing the conven ience key.
Electromechanical
parking brake
Operating
The electromechanical parking brake replaces
the hand brake.
Fig . 80 Center console : pa rk ing brake
" Pull the switch @¢ fig. 80 to set the parking
brake. The - (USA models),. (Canada
models) ind icator lights in the button and in
the instrument cluster display turn on .
" To release the parking brake, press the brake or
accelerator pedal while the ign ition is switched
on and press the button @at the same time.
The - (USA models), . (Canada models)
ind icator lights in the button and in the display
turn off.
Your vehicle is equipped with an electromechani­
cal park ing brake. The parking brake is designed
to prevent the vehicle from rolling un intent io nal ­
ly and replaces the hand brake .
In addition to the normal functions of a tradi­
t ional hand brake, the electromec hanical parking ..,.
85