AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual A4 1995 B5 / 1.G AUDI AUDI https://www.carmanualsonline.info/img/6/972/w960_972-0.png AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual
Trending: tow, wheel bolts, wheel bolt torque

Page 11 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual -  Adjust belt tension   page 13
-13
 .
Pa
ge 11 of 32 C
ylinder block, crankshaft and fl
ywheel, com
ponent la
yout
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&

Page 12 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual 13-13
      
Toothed belt, adjusting tension
 
     
-  Adjust toothed belt tension by turning tensioning 
roller to right and holding using 8 mm hex socket 
wrench. 
     
-  Tighten tensioning rolle

Page 13 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual 1) Always replace the center bolt.  2) Two turns of 90  are permissible.  
Pa
ge 13 of 32 C
ylinder block, crankshaft and fl
ywheel, com
ponent la
yout
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/D

Page 14 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual 13-14
      
Crankshaft oil seals, replacing
 
     
Toothed belt end (front)  
     
-  Remove toothed belt   page 13
-11
 .
     
-  Remove toothed belt sprocket from 
crankshaft. 
    
Note:  
Do n

Page 15 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual 13-15
      
Flywheel/drive plate end (rear)  
     
CAUTION! 
     
Always replace the seal with the flange, if 
available. Drain engine coolant before 
removing flange (  Repair Group 19). 
Replace

Page 16 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual 13-16
      
Flywheel pilot needle bearing, removing 
and installing
 
    
-  Remove bearing with puller assembly such as Kukko 21/2 and Kukko 
22-1, as shown 
-  Install bearing with drift 3264.
Pa

Page 17 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual 13-17
      
Dual mass flywheel or drive plate, 
removing and installing
 
     
Flywheel  
    
Note:  
The needle roller bearing is in the flywheel and must be pressed in when 
replacing the flywhee

Page 18 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual 13-18
      
Drive plate  
     
-  Hold crankshaft in position using crankshaft 
holder 3242   page 13
-11
 
    
CAUTION! 
Part numbers are listed for reference only. Always check with your 
Parts d

Page 19 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual 13-19
 
    
Note:  
Before installing the engine, make sure that the engine-to-transmission 
dowel sleeves are installed in the cylinder block flange.  -  Check clearance -a- between drive plate and

Page 20 of 32

AUDI A4 1995 B5 / 1.G AFC Engine Cylinder Block Crankshaft And Flywheel Component Assembly Manual 13-20
      
Engine speed (RPM) sensor mounting 
bracket, adjusting
 
     
Note:  
     The crankshaft must be at TDC and locked in 
position with crankshaft holder 3242   page 13
-
11
 . 
     
-  R
Page:   < prev 1-10 11-20 21-30 31-40 next >
Trending: wheel bolts, wheel bolt torque, tow