light AUDI A4 1995 B5 / 1.G Brakes Read Mesure Value Block Workshop Manual

01-65
Test table: display group 2 Read measuring value block
2
Indicated on display
0 or 1
0 or 1

0 or 1
0 or 1



ABS solenoid valve relay:
For vehicles with Front Wheel Drive (FWD), the display shifts one field toward
left.
0 not permitted during "Read measuring value block", the relay was not
activated during "ignition on".
- Carry out "Electrical test", step 11 page 01
-68
.
1 specified value, relay was activated by ABS control module -J104- during
ignition on.

Voltage at motor for ABS return flow pump:
For vehicles with Front Wheel Drive (FWD), the display shifts one field toward left.

0 specified value, there is no voltage at the motor for the ABS return flow pump. 1 not permitted during "Read measuring value block", there is voltage at the motor for the
ABS return flow pump.
- Carry out "Electrical test", step 12 page 01
-68
.

Brake light switch: Additional signal only for
All Wheel Drive (AWD):
Pa
ge 6 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

0 Brake pedal not operated1 Brake pedal operated

Electrical Wiring Diagrams, Troubleshooting & Component
Locations - Check brake light switch if there are deviations.
Brake light switch: Signal for Front
and All Wheel Drive:

0 Brake pedal not operated 1 Brake pedal operated


Electrical Wiring Diagrams, Troubleshooting & Component Locations - Check brake light switch if there are deviations.
Pa
ge 7 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-67
Test table: display group 3 Read measuring value block
3
Indicated on display
60 to
8000
1 RPM 0 to
100
%
0 or 1
---


Traction control (ASR) button: (Only for vehicles equipped with ASR)

0 Traction control button not operated. 1 The traction control button is operated, operational condition of ASR alternates, i.e. "ASR
OFF" and "ASR ON". When ASR is switched off via the traction control button, the warning lamp for ASR lights up.
- Check traction control button if there are deviations. Carry out "Electrical test", step 22 page 01
-
68
.

Actual engine torque (AET): (Only for vehicles equipped with ASR)
0% vehicle is in deceleration mode.20% - 30% represents engine idle.100% engine is offering its maximum torque.
- If no indication is displayed, proceed according to DTC 00647 "ABS-ASR engine electrical connection 2". DTC
table page 01
-98
.
Engine speed: (Only for vehicles equipped with ASR)

Engine speed is displayed in increments of 60 RPM, starting at 60 RPM.
Pa
ge 9 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-69


Note:
The operation manual for the VAS1978 wiring harness repair kit generally
forbids the repair of any lines in the ABS or related systems. This rule only
pertains to the shielded lines in these systems.
Multi-pin harness connector for ABS control module -J104- in proper
condition, with no bent, broken or corroded terminals. Replace any
damaged terminals using VAS1978 wiring repair kit. Ignition and electrical consumers switched off before beginning
testing (headlights, lighting, fan, etc.). For steps 13 through 16, raise the vehicle until the wheels rotate
freely. On vehicles with manual transmission put the gear shift lever in
neutral. On vehicles with automatic transmission move the selector
lever to position "N".
Pa
ge 12 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-73

Terminal
Wire connection to component ...
18
Engine Control Module (ECM); MMD signal (Masked Misfire Diagnostic)
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR, the SET signal (Specified Engine Torque) is
also transmitted via this wiring harness.
19
Hydraulic unit; control wire for ABS return flow pump -V39- 20
Engine Control Module (ECM); Engine RPM
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
25
Hydraulic unit; Left rear ABS outlet valve -N136- 26
Hydraulic unit; Right front ABS outlet valve -N100- 27
Hydraulic unit; right front traction control outlet valve -N167- (primary piston circuit) 28
Ground (GND) terminal 31 (ABS control module -J104-) 29
Ground (GND) terminal 31 (ABS control module -J104-) 31
Instrument cluster; activation of traction control indicator light
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
32
Instrument cluster; ABS/EDL warning light activation (active) 33
Hydraulic unit; Left front ABS outlet valve -N102- 34
Hydraulic unit; Right rear ABS outlet valve -N135- 35
Left front ABS wheel speed sensor -G47-
for vehicles with All Wheel Drive (AWD) and ABS/EDL
Pa
ge 17 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-74

Terminal
Wire connection to component ...
37
Hydraulic unit; activation of ABS solenoid valve relay -J106- 38
Right rear ABS wheel speed sensor -G44- 42
Right front ABS wheel speed sensor -G45-
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR for vehicles with All Wheel Drive (AWD) and ABS/EDL (throttle valve regulation)
44
Traction control (ASR) button
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
45
TI (Transmission Influence)
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
46
K-wire 47
Engine Control Module (ECM); AET (Actual Engine Torque)
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
47
Brake light switch -F-
for vehicles with All Wheel Drive (AWD) and ABS/EDL
48
Brake light switch -F- 50
Battery + (terminal 30) 53
Hydraulic unit; left rear ABS inlet valve -N134-
Pa
ge 19 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-75
Notes:
For test table:

The socket designations of the VAG1598 test box are identical to the terminal designations of the ABS control module
(w/EDL) -J104- in the wiring diagram. Incorrect test procedures can cause damage to the system. Do not bridge any
terminals other than those listed in the table.
Electrical Wiring Diagrams, Troubleshooting & Component Locations Specified values refer to readings on the VAG1526 and are not necessarily applicable for other test units.
If the measured values do not match specifications, carry out the corrective actions listed on the right side of the table.
Electrical Wiring Diagrams, Troubleshooting & Component Locations If values are obtained, also check wiring for intermittent loose terminals and short circuit to B+ and Ground (GND). This
applies especially to sporadic malfunctions.
Use the VAG1594 connector test kit for checking continuity (bridges).
If the measured values only differ slightly from the specifications, clean the sockets and harness connectors of the testers
and adapter leads (using contact spray G 000 700 04) and repeat the test. Before replacing actual components, check
wiring and connections once more. This is especially important if the specification for a resistance test is under 10 .
Pa
ge 21 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-88

Function test: ABS warning light -K47-
Test
step VAG
1598/20
sockets Test of
Test requirements
- Additional work stepsSpecified
value Corrective
action
19 - Function of ABS
warning light -K47- DTC memory checked and no DTC present
in DTC memory of ABS control module -
J104-. Ignition switched off Multi-pin connector connected to ABS
control module -J104- and retainer catch
engaged.
Test step 19: Continued on
next page.
Pa
ge 43 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-89

Function test: ABS warning light -K47-
Test step
VAG
1598/20
sockets Test of
Test
requirements
- Additional work
steps Specified value
Corrective action
19

Continuation: - Function of
ABS
warning
light -K47- - Switch on
ignition ABS warning
light -K47- lights
up for two (2)
seconds and
then goes out.
Electrical Wiring Diagrams,
Troubleshooting & Component Locations - If ABS warning light does not come on,
check voltage of electrical system and test
wiring from terminal 32 of ABS control
module -J104- to instrument cluster for
short circuit to Ground (GND).
- The ABS warning lamp does not switch
off after 2 seconds. The red "brake system
malfunction" symbol lights up after 2
seconds. Check wire from terminal 32 of
ABS control module -J104- to instrument
cluster for short circuit to B+ and open
circuit.

Repair Manual, Electrical Equipment,
Repair Group 90; Instrument cluster
- Are both the vehicle voltage and the
wiring from terminal 32 of ABS control
module -J104- to the instrument cluster
OK? Malfunction in instrument cluster. Pa
ge 44 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-90

Function test: Red brake warning symbol
Test
step VAG
1598/20
sockets Test of
Test requirements
- Additional work stepsSpecified
value Corrective
action
20 - Function of red "brake
system malfunction"
symbol
Repair Manual, Brake System, Repair
Group 47

Brake fluid level is OK Function of ABS warning light -K47-
already checked in step 19. Multi-pin connector connected to ABS
control module -J104- and retainer
catch engaged. Switch on ignition
Test step 20: Continued on
next page.
Pa
ge 45 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8