AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual A4 1995 B5 / 1.G AUDI AUDI https://www.carmanualsonline.info/img/6/1186/w960_1186-0.png AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual
Trending: torque, boot, wheel bolts

Page 1 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual 40-54
 
     
Wheel bearing housing, 
removing and installing 
     
Removing  
     
-  Remove wheel trim.
     
   On light alloy wheels use puller in vehicle tool kit 
to remove trim cap. 
     
-

Page 2 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual Suspend the brake caliper using a piece of wire. Do not allow the 
caliper to hang by the brake hose. The unsupported weight can 
stretch and damage the hose. Do not loosen brake hoses or lines.
-  Re

Page 3 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual 40-55
 
    
-  Remove bolts -1- for brake splash guard.
-  Pull ABS wheel speed sensor out of wheel bearing housing.
-  Loosen nuts -2- and -3-. 
    
-  Pull out rubber grommet -1- and disconnect ha

Page 4 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual 40-56
 
    
-  Remove bolt -3- and nut -4-.
-  Disconnect tie rod end. 
-  Loosen nut from ball joint 
  -  If necessary, counterhold ball joint using 4 mm hex wrench.
    
Note:  
For vehicles with

Page 5 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual 40-57
      
Note:  
     Cover the CV joint boot (e.g. by inserting a piece 
of leather) to protect it from damage. 
    
CAUTION! 
For safety reasons, reinstall the flanged nut onto the lower track

Page 6 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual 40-58
      
Installing  
     
-  Install wheel bearing housing.
     
-  Slide drive axle outer CV joint into wheel hub 
and tighten new bolt hand tight. 
     
-  Install ball joints for lower trac

Page 7 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual 40-59
      
-  Install ABS wheel speed sensor.
     
-  Attach linkage for headlight range control   
page 40
-14
 . 
     
-  Bolt on brake splash guard.
     
   Tightening torque: 10 Nm (7 ft lb)

Page 8 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual      
The vehicle must be standing on its wheels 
when loosening or tightening the bolt for the 
drive axle. Otherwise the risk of an accident 
exists. 
     
-  Check front suspension alignment and,

Page 9 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual 40-60
 
  
Wheel bearing housing, servicing
 
1 - 
Wheel bearing housing 
Note different versions of suspension   
parts catalog microfiche Removing and installing   page 40
-54
2 - 
Wheel bearing 
Sh

Page 10 of 17

AUDI A4 1995 B5 / 1.G Suspension Wheel Bearing Housing Remove And Install Workshop Manual 40-61
 
  
3 - 
Wheel hub 
Shouldered
  With 75 mm diameter wheel bearing 
housing: Pressing hub out   Fig. 1Pressing hub in   Fig. 9
  With 82 or 85 mm diameter wheel bearing 
housing: 
Pressing hub
Page:   1-10 11-20 next >
Trending: boot, torque, wheel bolts