wheel AUDI A4 1998 B5 / 1.G 01V Transmission Remove And Install User Guide

37-98


Continuation for all vehicles
Radio operating manual
Tightening torque table Page 37
-119
onward. - Bolt heat shield -B- for driveshaft to Torsen differential cover (arrows) if
installed.
- Install heat shield -A- above driveshaft.
- Install bracket for noise insulation panel.
- Install noise insulation panel.
- Install front wheels.
- Connect battery Ground (GND) strap.
- Check adjustment of selector lever cable page 37
-45
.
- Check gear oil in final drive with transmission installed page 39
-1 .
- Then check ATF level and top off Page 37
-133
onward.
- After connecting battery, enter anti-theft code for radio.- Fully close power windows to stop.
- Then activate all power window switches ("up") for at least one second
to activate automatic window raising/lowering.
- Set clock to correct time.
Pa
ge 28 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-102

- Assemble both 10-222A/3 engine support
adapters for front and rear spindles on support
bar.

- Set 10-222A engine support bridge onto the fender mounting flanges
using 10-222A/1 brackets.
- Hang both spindles on the adapters.
- Secure engine to spindles. To do so, additionally use a shackle -1- at
the rear side of the engine to avoid damage.
- Take up weight of engine/transmission assembly on spindles.
- Tighten the rear spindle less, to enable later lowering at rear.
- Raise vehicle.
- Remove front wheels.

- Remove sound-deadening pan.
- Remove bracket for noise insulation panel.
Pa
ge 32 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-103


Repair Manual, Suspension, Wheels, Steering, Repair Group 40
- Remove left and right heat shields for drive axles (arrows).
- Disconnect drive axles from transmission drive flanges.

- Unbolt engine speed (RPM) sensor -G28- (arrow B) from transmission
at front left.
- Remove connector for speedometer (arrow -A-) from transmission.
Pa
ge 33 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-105

For vehicles with the illustrated vertical headlight
aim control system, notes in the following repair
manuals must be observed before lowing
subframe;
Repair Manual, Suspension, Wheels, Steering,
Repair Group 40; control arm removing and installing; sensor for vehicle leveling in vehicles with automatic vertical headlight aim control regulation.

Otherwise the sensor may be destroyed.
Pa
ge 35 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-107


Automatic Transmission 01V with All Wheel Drive is supported at the
same positions as the Front Wheel Drive version.
WARNING!
When working on the subframe, all precautions and notes which are
listed in Repair Manual, Suspension, Wheels, Steering must be
must be observed. - Roll VAG1383A engine/transmission hoist with 3282 transmission
support under transmission and support transmission.
- Align adjustment plate parallel to transmission.
- Secure transmission on 3282 transmission support using bolt -A-.

Repair Manual, Suspension, Wheels, Steering, Repair Group 40;
Subframe, removing and installing
- Before loosening carrier, special tool 3393 must be used to check
whether holes -1- and -2- line up.
- Completely lower subframe at rear and front.
Pa
ge 37 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-117


Repair Manual, Suspension, Wheels, Steering, Repair Group 40;
Subframe, removing and installing

Repair Manual, Suspension, Wheels, Steering, Repair Group 44,
Vehicle alignment
- Install bolts of torque converter through opening -A- in engine flange to
the drive plate (turn crankshaft 1/3 rotation each time).
- Insert plug into opening -A- in engine flange.
- Install subframe, observe tightening sequence and alignment with
master hole.
- Only perform vehicle alignment if necessary.- Install transmission supports at left and right with transmission mount
page 37
-125


- Remove bolt -A- after transmission is bolted to engine.
- Apply corrosion protection to contact surface between bolt -A- and oil
pan.
- Bolt on ATF lines page 37
-149
Pa
ge 47 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-118

- Bolt drive axles to transmission flanges.

Repair Manual, Suspension, Wheels,
Steering, Repair Group 40


- Bolt driveshaft to transmission flange page
39
-79
, Driveshaft, removing and installing.

- After connecting battery, enter anti-theft code for
radio.

Radio operating manual
- Check adjustment of selector lever cable
page 37
-45
.

- Check gear oil in final drive with transmission
installed page 39
-1 .

- Then check ATF level and top off Page 37
-
133
onward.

- Fully close power windows to stop.

Pa
ge 48 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-132


For transmissions with Front Wheel Drive (FWD), the VW540 holding
fixture can also be used to secure the transmission to the VW313 holding
fixture. - Attach the 3457 attachment and holding rig at the transmission housing
mounts and secure.
- Bolt the attachment and holding rig to the VW 309 holding plate and
place this into the VW313 holding fixture using a workshop crane.

WARNING!
The center of gravity of the transmission is located outside the
turning center at holding fixture. To turn the transmission, a second
technician must hold the transmission housing to prevent back-
swing.
Note:
Vents for the transmission housing and final drive must be closed before
turning a filled transmission on the assembly stand so that the oil pan
faces upward . - Secure transmission to VW540 holding fixture (arrows) and insert in
VW313 holding fixture.
Pa
ge 64 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2