wiring AUDI A4 1998 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Owner's Guide

01-74

Output on GST
and/or on VAG 1551
scan tool Possible malfunction cause

Malfunction repair
P0337 / 16721
Crankshaft Position
Sensor Circuit Low
Input Harness connector for Crankshaft Position
(CKP) sensor -G4- loose or corroded due to
moisture in the harness connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 28
-7

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Crankshaft Position (CKP) sensor -G4-
loose or distance to groove on crankshaft
counterweight greater than 1.3 mm (0.053
in.)

- Check crankshaft position sensor -G4- for
correct installation and tight fit

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again

Wiring connection to Crankshaft Position
(CKP) sensor -G4- faulty, or sensor -G4-
faulty

- Check crankshaft position sensor -G4-
page 28
-19


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
Pa
ge 100 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-83

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0452 / 16836
Evaporative Emission
Control System Pressure
Sensor Low Input Harness connector on sensor for EVAP
canister -G172- (differential pressure sensor)
loose or corroded due to moisture in the
harness connector

- Check harness connector for tight fit
and contact corrosion, if necessary
reconnect and/or clean

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
MIL lights up immediately Wiring connection to sensor for EVAP
canister -G172- (differential pressure sensor)
faulty, or sensor -G172- faulty

- Check sensor for EVAP canister -
G172- (differential pressure sensor)
page 24
-61


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
For troubleshooting
Display group 030
Engine Control Module (ECM) -J192- faulty

- Replace and code engine control
module page 01
-265
erase DTC
memory and test drive check DTC
memory
Note:
The malfunction "P0542 / 16836" is set as soon after engine start as the differential pressure sensor signal is less than 0.1 V
Pa
ge 111 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-84

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0453 / 16837
Evaporative Emission
Control System Pressure
Sensor High Input Harness connector on sensor for EVAP
canister -G172- (differential pressure sensor)
loose or corroded due to moisture in the
harness connector

- Check harness connector for tight fit
and contact corrosion, if necessary
reconnect and/or clean

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
MIL lights up immediately Wiring connection to sensor for EVAP
canister -G172- (differential pressure sensor)
faulty, or sensor -G172- faulty

- Check sensor for EVAP canister -
G172- (differential pressure sensor)
page 24
-61


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
For troubleshooting
Display group 030
Engine Control Module (ECM) -J192- faulty

- Replace and code engine control
module page 01
-265
erase DTC
memory and test drive check DTC
memory
Note:
The malfunction "P0453 / 16837" is set as soon after engine start as the differential pressure sensor signal is greater than 5.0
Pa
ge 113 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-85

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0461 / 16845
Fuel Lever Sensor Circuit
Range/Performance Wiring connection between Engine Control
Module (ECM) -J192- and instrument panel
insert faulty

- Check fuel level signal page 24
-
107


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
Malfunction not displayed by
MIL Malfunction on instrument cluster or fuel
level sensor

Repair Manual, Electrical
Equipment - Check instrument cluster
For troubleshooting Display
group 027
Malfunction cause found: Yes


- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Note:
The malfunction "P0461 / 16845" is set with ignition on as soon as a voltage signal over 10.8 V is recognized for longer than
15 sec.
Pa
ge 115 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-86

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0501 / 16885
Vehicle Speed Sensor
Range/Performance Wiring connection between vehicle speed
sensor and engine control module has open
circuit

- Check vehicle speed signal page 24
-97

MIL Status:
MIL lights up immediately Malfunction cause found: Yes


- Erase DTC memory, test drive and
after test drive, check DTC memory
again
For troubleshooting Display
group 019

Notes:
The malfunction "P0501/ 16885" is set after engine start as soon as, at a coolant temperature over 80 C (176 F) and an
engine speed signal between 1300 RPM and 6000 RPM the vehicle speed signal during a deceleration fuel shut off is less
than 1 km/h (1 mph). The duration of the deceleration fuel shut off must be longer than 3 sec.
Pa
ge 116 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-88

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0706 / 17090
Transmission Range Sensor
Circuit Range/Performance Engine control module incorrectly coded

- Cause: the vehicle is equipped with
manual transmission, but was coded
for vehicle with automatic
transmission.
- Remedy: code vehicle correctly
according to Coding Table

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
Malfunction not displayed by
MIL Automatic transmission: faulty wiring
connection between Engine Control Module
(ECM) -J192- and multi-function Transmission
Range (TR) switch -F125-

- Check gear recognition signal
page 24
-99

For troubleshooting
Display group 004
Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again

Automatic transmission: malfunction of
multi-function Transmission Range (TR) switch
-F125-

Repair Manual, 5 Spd. Automatic
Transmission 01V On Board Diagnostic (OBD), Repair Group 01
- Check multi-function Transmission
Range (TR) switch -F125-

Malfunction cause found: Yes

Pa
ge 118 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-89

Output on GST and/or
on VAG 1551 scan
tool Possible malfunction cause

Malfunction repair
P0707 / 17091
Transmission Range
Sensor Circuit Low
Input Wiring connection between Engine Control
Module (ECM) -J192- and multi-function
Transmission Range (TR) switch -F125- on
automatic transmission faulty

- Check gear recognition signal page 24
-99


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
Malfunction not
displayed by MIL Malfunction on multi-function Transmission
Range (TR) switch -F125- of automatic
transmission

Repair Manual, 5 Spd. Automatic
Transmission 01V On Board Diagnostic (OBD), Repair Group 01, Electrical testing

- Check multi-function Transmission
Range (TR) switch -F125-
For troubleshooting
Display group 004
Malfunction cause found: Yes


- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Pa
ge 120 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-90

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1101 / 17509
(B1-S1) Voltage too
Low/Air Leak Harness connector for Heated Oxygen
Sensor (HO2S) -G39- (B1-S1) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Leak in Bank 1 exhaust system before
Heated Oxygen Sensor (HO2S) -G39- (B1-
S1)

- Determine and repair leak

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again

Wiring connection to Heated Oxygen
Sensor (HO2S) -G39- (B1-S1) faulty, or
sensor -G39- faulty

- Check HO2S -G39- (B1-S1) page 24
-
49

For troubleshooting
Display group 010
Malfunction cause found: Yes
No
Continued next page

- Erase DTC memory, test drive and after
test drive, check DTC memory again
Pa
ge 121 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-92

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1102 / 17510
Heating Circ. (B1-S1)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z19- (B1-S1) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Wiring connection of Oxygen Sensor
(O2S) heater -Z19- (B1-S1) faulty, or heater
-Z19- faulty

- Check O2S heater -Z19- (B1-S1) page 24
-51


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Notes:

|The heating of the oxygen sensor probes in front of Three Way Catalytic Converter (TWC) is switched on with the fuel
pump relay, i.e. immediately at engine start.
Pa
ge 123 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-94


Wiring connection to Oxygen Sensor (O2S) behind Three
Way Catalytic Converter (TWC) -G130- (B1-S2) faulty, or
sensor -G130- faulty

- Check O2S behind three way catalytic converter -
G130- (B1-S2) page 24
-53


Malfunction cause found: Yes
No
Continued next page

- Erase DTC memory, test drive and after test drive,
check DTC memory again

Engine Control Module (ECM) -J192- faulty

- Replace and code engine control module page 01
-265
erase DTC memory and test drive
check DTC memory
Note:
The malfunction "P1104 / 17512" is set 123 sec after engine start, coolant temperature over 80 C (176 F), oxygen sensor
control active, engine speed between 1500 min and 5000 min, load between 19% and 80% and probe heater switched on at
least 45 sec, as soon as the signal voltage is less than 0.040 V for longer than 60 sec.
Pa
ge 126 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1