AUDI A4 1999 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Workshop Manual

01-206
Note on display field 2: X
X
Meaning of 2-digit display:

1 = Shifting signal (ignition angle retard):
Value "0" = Ignition angle retarding not active
Value "1" = Ignition angle retarding active
Notes:

Because of the brief signal, the shift is not always displayed.
On vehicles without automatic transmission, "0" is always displayed.
Check shift signal page 24
-101
.

2 = Gear recognition signal:
Value "0" = Selector lever in R, D, 4, 3, or 2 (driving mode engaged)
Value "1" = Selector lever in P or N
Notes:

On vehicles without automatic transmission, "0" is always displayed.
Check gear recognition signal page 24
-99
.
Pa
ge 291 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-207
Note on display field 3: X
X
Meaning of the 2-digit display:

1 = A/C compressor off/on (0 = off; 1 = on)
Notes:

On vehicles without A/C "0" is always displayed.
Check A/C compressor page 24
-90
.
The A/C compressor is shut off for approx. 12 sec. by -J192- when accelerating from a stop and from low speed.
If the gas pedal is released sooner, the time is reduced to a minimum of 3 sec. At wide open throttle, the A/C
compressor is switched off by the automatic transmission (kick-down switch).

2 = Rear window heating - Signal (0 = off; 1 = on)
Notes:
The rear window heating signal is only displayed on vehicles without A/C.
On vehicles with A/C "0" is always displayed.
Check rear window heater signal page 24
-88
.
Notes on display field 4:

If the A/C compressor is off display field 3; display field 4 can be used to recognize whether the compressor was
switched off by the engine control module. Meaning of the 1-digit display:
Pa
ge 292 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

X
Meaning of 1-digit display

Value "0" = A/C compressor not switched off by engine control module
Value "1" = A/C compressor switched off by engine control module
Pa
ge 293 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-208
Display groups 024, 025 and 026
Notes:

Display group 024 is currently not assigned.
Display groups 025 and 026 are only used by Production.
Display shows
Values
Designation
Basic setting 24
1 2 3 4 -------- --------------------------------------
-------- --------------------------------------
-------- --------------------------------------
-------- -------------------------------------- Display shows
Values
Designation
Basic setting 25
1 2 3 4 0s --------------------------------------
0.0s --------------------------------------
0s --------------------------------------
0.0s -------------------------------------- Display shows
Values
Designation
Pa
ge 294 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

Basic setting 26
1 2 3 4 0 - 255 --------------------------------------
0 - 255 --------------------------------------
0 - 255 --------------------------------------
0 - 255 --------------------------------------
Pa
ge 295 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-209
Display group 027 Display
shows Display specified
value Designation/diagnosis
Basic setting
27
1 2 3 4 X 1 = Malfunction Indicator Lamp (MIL) wire from Transmission Control Module
(TCM)
X 2 = Fuel level signal from instrument cluster
0.000 V 3 = ---------------
0.000 V 4 = --------------- Notes on display field 1:

On vehicles with manual transmission, "1" is always displayed.
Checking Malfunction Indicator Lamp (MIL) wire from transmission control module page 24
-105
.
X
Meaning of the 1-digit display:

Value "0" = ignition on, engine not running
Value "1" = engine running Note on display field 2:

Check fuel level signal from instrument cluster page 24
-107
.
Pa
ge 296 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

X
Meaning of the 1-digit display:

Value "0" = ignition on and engine not running, or, engine running and fuel tank contents less than 12 liters (3.2 gal)
Value "1" = engine running and fuel tank contents greater than 12 liters (3.2 gal)
Pa
ge 297 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-210
Display group 028
Note:
Display group 028 is only used by Production. Display shows
Display/specified value
Designation
Basic setting 28
1 2 3 4 0 - 255 --------------------------------------
0 - 255 --------------------------------------
0 - 255 --------------------------------------
0 - 255 --------------------------------------
Pa
ge 298 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-211
Display group 029 (Diagnosis status)
Notes:
OBD II regulations require a display ("Readiness Code") that indicates readiness for inspection (annual exhaust emissions
test). The readiness code display (display field 1) shows that every component and/or system that affects the exhaust, which
can lead to switching on the MIL, has been operated at least once with positive result.
The readiness code is reset and/or erased:

Every time the DTC memory is erased (both with address word 01 function 05 and with address 33 mode 4).
When the battery is disconnected.
When the engine control module is disconnected (e.g. connecting test box VAG 1598/19, replacing ECM, etc.).
To generate the readiness code, take a "mixed city and highway" drive (short test). A "mixed city and highway" drive is
understood to be approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with manual transmission in 4th or 5th gear, or
automatic transmission selector lever in "D" position, preferably in 4th gear.
The "Trip Status" display (display field 2) shows which components and/or systems have been checked since the start of the
trip. After successful diagnosis, the current display value is set to "1" whether the diagnosis was recognized as OK or not OK.
The trip-status display is reset to "0" at each start since the components and/or systems are checked at each new start. A
"trip" is understood to be a drive of approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with manual transmission in 4th or
5th gear, or automatic transmission selector lever in "D" position, preferably in 4th gear, with preceding cold start.
The readiness code display (display field 1) shows whether the components and/or systems checked in display field 2 were
recognized as OK or not OK by the engine control module.
If the diagnosis is recognized as OK, the current display value is set to "0."
Pa
ge 299 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

If the diagnosis is recognized as not OK, the current display value is not set to "0", it stays at "1."
If every component and/or system has operated at least once with positive results, all display values of the readiness code
are set to "0."
If, during another diagnosis, a component and/or system is recognized as not OK, the readiness code is not reset to "1."
Pa
ge 300 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1