light AUDI A4 1999 B5 / 1.G Brakes Output DTM 03 Workshop Manual

01-151

Notes:

To avoid overloading the components being
checked, they are actuated during the test
sequence for a period of 60 (or 90) seconds.
The actuator test will be terminated if the "
button" is not pressed within this period.

The ABS warning light and the red "brake
system malfunction" symbol blink during the
test.
Pressing the brake pedal repeatedly this
relieves the vacuum in the brake booster. For
this reason, the brake pedal must be pressed
harder in order to achieve the same braking
effect. Your work will be easier if you run the
engine briefly. This will build up vacuum in the
brake booster again.
Pa
ge 4 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-165

-
Press button.Output Diagnostic Test Mode (DTM)
-
End

Indicated on display:
Note:
The output diagnostic test mode is completed. The ABS/EDL warning light
and the red warning symbol for brake system go out.
-
Press button.
Rapid data transfer
HELP
Select function XX

Indicated on display:
Note:
If the ABS/EDL warning light does not go out, this indicates a
malfunction in the system. Observe test sequence exactly page 01
-
17
.
- Press buttons -0- and -6- to select "End Output" function 06. Press -Q-
button to confirm input.
Pa
ge 19 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-167


Note:
The operation manual for the VAS1978 wiring harness repair kit generally
forbids the repair of any lines in the ABS or related systems. This rule only
pertains to the shielded lines in these systems.
Multi-pin harness connector for ABS control module -J104- in proper
condition, with no bent, broken or corroded terminals. Replace any
damaged terminals using VAS1978 wiring repair kit. Ignition and electrical consumers switched off before beginning
testing (headlights, lighting, fan, etc.).
Pa
ge 21 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-171

Terminal
Wire connection to component ...
10
Electrical connection to instrument cluster
Only for vehicles equipped with EDL. The time signals used to calculate standing time are transmitted via
this harness connector
11
K-wire 13
MMD signal (Masked Misfire Diagnostic)
For vehicles equipped with ASR, the SET signal (Specified Engine Torque) is also transmitted via this wiring
harness.
14
Brake light switch -F- 15
Voltage supply, terminal 15 16
Ground (GND) terminal 31 (ABS hydraulic pump -V64-) 17
Battery + (terminal 30) 18
Battery + (terminal 30) 19
Ground (GND) terminal 31 (ABS control module -J104-) 20
Traction control (ASR) indicator light activation
Only for vehicles equipped with ASR.
21
ABS/EDL warning light activation 23
Speed sensor output rear left
For vehicles with navigation system
Pa
ge 25 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-173
Notes:
For test table:

The socket designations of the VAG1598 test box are identical to the terminal designations of the ABS control module
(w/EDL) -J104- in the wiring diagram. Incorrect test procedures can cause damage to the system. Do not bridge any
terminals other than those listed in the table.
Electrical Wiring Diagrams, Troubleshooting & Component Locations Specified values refer to readings on the VAG1526 and are not necessarily applicable for other test units.
If the measured values do not match specifications, carry out the corrective actions listed on the right side of the table.
Electrical Wiring Diagrams, Troubleshooting & Component Locations If values are obtained, also check wiring for intermittent loose terminals and short circuit to B+ and Ground (GND). This
applies especially to sporadic malfunctions.
Use only the VAG1594 connector test kit for checking continuity (bridges).
If the measured values only differ slightly from the specifications, clean the sockets and harness connectors of the testers
and adapter leads (using contact spray G 000 700 04) and repeat the test. Before replacing actual components, check
wiring and connections once more. This is especially important if the specification for a resistance test is under 10 .
Pa
ge 28 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-176

Set measurement range:
voltage test (20 V =)
Test
step VAG
1598
sockets Test of
Test requirements
- Additional work
steps Specified
value Corrective action
3 19 + 14 Function of brake
light switch -F- Ignition switched
off
- Check wire from terminal 19 to Ground
(GND).
Brake pedal not
depressed
- Operate brake pedal.0.0 -0.5 V

10.0 - 14.5
V
Electrical Wiring Diagrams,
Troubleshooting & Component Locations

Repair Manual, Brake System, Repair
Group 45
- Check wiring from terminal 14 to
terminal 30 via fuse (10A).
- Check brake light switch -F-
- Adjust brake light switch -F-.
Pa
ge 31 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-179

Function test: ABS/EDL warning light -K47-
Test
step VAG
1598
sockets Test of
Test requirements
- Additional work stepsSpecified
value Corrective
action
8 - Function of ABS/EDL
warning light -K47-. DTC memory checked and no DTC present
in DTC memory of ABS control module -
J104-. Ignition switched off Multi-pin connector connected to ABS
control module -J104- and retainer catch
engaged.
Test step 8: Continued on
next page.
Pa
ge 34 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-180

Function test: ABS/EDL warning light -K47-
Test step
VAG
1598
sockets Test of
Test
requirements
- Additional work
steps Specified value
Corrective action
8

Continuation: - Function of
ABS/EDL
warning light
-K47-. - Switch on
ignition ABS warning
light -K47- lights
up for two (2)
seconds and
then goes out.
Electrical Wiring Diagrams,
Troubleshooting & Component Locations - If ABS/EDL warning light does not come
on, check voltage of electrical system and
test wiring from terminal 21 of ABS control
module -J104- to instrument cluster for
short circuit to Ground (GND).
- The ABS/EDL warning lamp does not
switch off after 2 seconds. The red "brake
system malfunction" symbol lights up after
2 seconds. Check wire from terminal 21 of
ABS control module -J104- to instrument
cluster for short circuit to B+ and open
circuit.

Repair Manual, Electrical Equipment,
Repair Group 90.
- If vehicle voltage and wire from terminal
21 of ABS control module -J104- to
instrument cluster are OK there is a
malfunction in instrument cluster, LED or
bulb malfunctioning.
Pa
ge 35 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-181

Function test: Red brake warning symbol
Test
step VAG
1598
sockets Test of
Test requirements
- Additional work stepsSpecified
value Corrective
action
9 - Function of red "brake
system malfunction"
symbol
Repair Manual, Brake System, Repair
Group 47

Brake fluid level is OK Function of ABS warning light -K47-
already checked in step 8. Multi-pin connector connected to ABS
control module -J104- and retainer catch
engaged. Switch on ignition
Test step 9: Continued on
next page.
Pa
ge 36 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-182

Function test: Red brake warning symbol
Test step
VAG
1598/20
sockets Test of
Test requirements
- Additional work stepsSpecified value
Corrective action
9

Continuation: Function of red
"brake system
malfunction"
symbol - Connect VAG1551 scan
tool and select address
word 03
- For vehicles with
automatic transmission and
high-line instrument cluster,
depress the brake pedal
and select a driving gear. The ABS indicator lamp
and the red "brake system
malfunction" symbol light
up. If the traction control
indicator light is installed
and OK, it also lights up. Repair Manual,
Electrical Equipment, Repair Group 90; instrument cluster.

- Malfunction in
instrument cluster
Pa
ge 37 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13