brake light AUDI A4 2000 B5 / 1.G 01V Transmission Electrical Testing Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2000, Model line: A4, Model: AUDI A4 2000 B5 / 1.GPages: 66, PDF Size: 0.28 MB
Page 7 of 66

01-277
 88-pin connector for Transmission Control Module (TCM) -J217- (sockets on VAG1598/20)  
1-   Solenoid valve 5 -N92-   18-
  Kick-down switch -F8- (not for E-gas and V6-TDI)  
2-   Shift lock solenoid -N110-   19-
  Control input to transmission from ABS control module  
3-   Vacant   20-
  Engine intervention (via ignition timing) 
1)  
4-   Solenoid valve 7 -N94-   21-
  ATF temperature sensor -G93-   
5-   Solenoid valve 4 -N91-   22-
  ATF temperature sensor -G93-   
6-   Ground (GND) for power consumers, term. 
31  23-
  Sensor for transmission RPM -G182- (shielding)  
7-   Vacant   24-
  Vacant  
8-   Multi-function TR switch -F125-, L2   25-
  Selector lever display (not for Highline combi)  
9-   Multi-function TR switch -F125-, L4  
supply voltage for cruise control system  26-
  Supply voltage (terminal 30) with or without fuses depending on 
model   wiring diagram  
10-
  Brake light switch -F- (not for E-gas and 
V6-TDI)  27-
  Kick-down for air conditioning 
1)  
11-
  Vacant   28-
  Ground (GND) for electronics (terminal 31)
4)   
12- Vacant   29- Solenoid valve 6 -N93-  
Pa
ge 7 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16 
Page 12 of 66

01-280
 List of test steps (88-pin connector)  
 
Only perform test steps for the relevant component, as listed in DTC and Read Measuring Value Block tables.
Item checked    
Item checked    
Supply voltage for TCM -J217-  
- Perform test 
steps 1 and 7 Solenoid valve 5 -N92- (Pressure control 
valve -2- -N216-)  - Perform test steps 13 
and 8 
Shift lock solenoid -N110-  
- Perform steps 2, 
6 and 16 Solenoid valve 6 -N93- (pressure control 
valve -3- -N217-)  - Perform test steps 14 
and 8. 
Brake light switch -F-  
- Perform test 
step 3. Solenoid valve 7 -N94- (pressure control 
valve -4- -N218-)  - Perform test steps 15 
and 8. 
Supply voltage for cruise 
control system  - Perform test 
step 4. Transmission VSS -G38- (Sensor for 
transmission output RPM -G195-)  - Perform test step 18.
Kick-down switch -F8-  
(not for E-gas)  - Perform test 
steps 5 and 17 Sensor for transmission RPM -G182-  
- Perform test step 19.
Multi-function TR switch 
(driving range sensor) -F125-  -  page 01
-322
ATF temperature sensor -G93-  
- Perform test step 20.
Solenoid valve 1 -N88-  
- Perform test 
steps 8 and 9 Wiring connection to ECM
1)  
- Perform test steps 21, 
22, 23, 24, and 25 
1) Signal is transmitted to Transmission Control Module (TCM) via the Engine Control Module (ECM). Test is only for vehicles 
without CAN-bus.  
Pa
ge 12 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16 
Page 16 of 66

01-283
 
Voltage measurement: switch multimeter to 20 V measuring range  
Test step  
VAG  
1598/20  
sockets  Test of  
Test conditions 
- Additional stepsSpecified  
value  Corrective action  
3 
1)  
10 + 6  
10 + 
28
2)  Brake light switch  
-F-  
Ignition switched 
on Brake pedal not 
depressed less than 1 V  
- Check wiring per wiring 
diagram. 
- Replace and adjust brake 
light switch -F-. 
not for E-gas 
engines       
- Brake pedal 
depressed approx. battery 
voltage   Repair Manual, Brake 
System, Repair Group 47
   
4   9 + 6  
9 + 28
2)  Supply voltage for 
Cruise Control, Control 
Module  
-J213-  
Ignition switched 
on Selector lever in 
D, 4 and 3 approx. battery 
voltage  - Check wiring from terminals 
6 and 28 to Ground. 
- Check wiring from terminal 9 
to terminal 15 of central 
electrics. 
- Check wiring to cruise 
control, control module -J213- 
- Check multi-function switch -
F125-  page 01
-322
 
        
Selector lever in 
P, R, N, and 2 less than 5 V  
  - Check fuse 31
Pa
ge 16 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16 
Page 17 of 66

1) This test cannot be performed on vehicles with E-gas. The signal is transmitted from brake light switch or brake test switch 
to Engine Control Module (ECM). The ECM then forwards the signal to the Transmission Control Module via the CAN-Bus.  2) Pin 28 at the control module is vacant for vehicles with 10-pin connector of multi-function switch -F125-.  
Pa
ge 17 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16