ESP AUDI A4 2018 Owners Manual

a co .... N ,....
N .... 0 0
3 co
q page 353. In some cases, you must drive for
several minutes after storing the pressures until
the indicator light turns off . If the indicator lig ht
does turn off or turns on aga in after a short peri­
od of time, drive to an authorized Audi dealer or
author ized Audi Service Facility immed iately to
have the ma lfunction corrected .
A WARNING
-If the t ire pressu re indica tor appea rs in the
display, red uce your speed immed iate ly and
avoid any har d st eer ing or braking maneu­
vers. Stop a s soon as possib le and check the
ti res and their press ure.
- T he driver is responsi ble for main taining the
cor rect ti re pressure. You must check the
tire pressure regu larly .
- Under certa in conditions (s uch as a sporty
driving style, winte r cond itio ns or unpaved
roads), the tire pressure monitoring system
indicator may be delayed.
(D Tips
- The t ire press ure monitoring sys tem can al ­
so stop work ing when there is an ESC mal ­
funct ion .
- Usin g snow chains may result in a system
malfunction.
- The t ire press ure moni toring sys tem in yo ur
A udi was ca librated with "A udi Orig inal
Tires"¢
page 341 . Using these ti res is rec­
ommended.
Storing tire pressures
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­ tem.
~ Make s ure before storing that the tire pressures
of a ll fo ur ti res meet the specified values and
are adapted to the load
¢ page 344.
~ Switch the ign ition on.
~ Select in the Infotainment system: I MENUI but­
ton
> Vehicle > Service & checks > Tire pre s­
s ure monitoring > Store tire pres sure > Yes ,
store now .
Wheel s
{!) Tips
Do not store the tire pressures if snow chains
are installed.
353

Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value.
It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The required cleaning and care products can be
obtained from an authorized Audi dealer or au­
thorized Service Facility. Read and follow the in­
structions for use on the packaging .
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health .
- Always store cleaning and care products out
of reach of children to reduce the risk of poi­
soning .
@ For the sake of the environment
- Preferably purchase environmentally-friend­
ly cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the ve­ hicle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect .
Before washing, rinse off heavy deposits with
plenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a microfiber cloth.
Also, wash the underside of your vehicle once road salt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash ­
er, always follow the operating instructions pro­
vided with the pressure washer. This is especially
important in regard to the pressure and spraying
distance. Do not aim the spray directly at the
354
seals on the side windows, doors, lids or the sun­
roof* or at tires, rubber hoses, insulating materi­
al, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozzles or high pressure nozzles.
The water temperature must not be above 140 °F
(60 °().
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows and roof* are closed
and the windshield wipers are off . Follow instruc­
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean the vehicle starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi­
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint .
Apply the product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft micro­
fiber cloth .
Rinse the vehicle thoroughly again and let it air
dry. Remove any water residue using a chamois .
A WARNING
-
- Only wash the vehicle when the ignition is
off and follow the instructions from the car

Care and cleaning
Component Situation Solution
E x haust tail p ipe s
Road salt Water, cleaning solution suitab le for stainless steel, if nee-
essary
D eco ra tiv e part s/ Deposits M
ild soap so lution a), a cleaning so lution s uitable fo r stain-
trim less stee l, if necessary
Paint Paint damage Refer to t he paint number on the vehicle data label, repair
with touch up
pa int ~ page 379
Spilled fuel Rinse with water
immediately
Surface rust Rust remover, then protect w ith hard wax; for questions,
consult an author ized A udi dealer or authorized Aud i Serv-
ice Facility.
Corros ion Have it removed by an authorized Audi dea ler or author-
ized Audi Service Facil ity.
Water no longer P
rotect wi th hard wax (at least tw ice per year)
beads on the sur face
of clean paint
No shine even though Treat wit h su itable polish; then apply paint protectant if
paint has been pro- the polish that was used does not conta in any protectant
tected/pa int looks
poor
Deposits such as in- Dampen w ith water immediately and remove w it h a micro-
sects, bird dropp ings, f iber cloth
tree sap and road salt
Grease-based con- Remove immediately with a mi ld soap so lution
a) and a
taminants such as soft cloth
cosmetics or sunblock
Carbon parts Deposi ts Inter ior: clean the same way as plastic parts
E xterior : clean the same way as painted pa rts
Decorat iv e decal s Deposits Soft sponge with a mild soap solutiona l
a) Mi ld soap solution: maximum two tablespoons of neutral soap in 1 quar t Cl liter) of water
Interior cle aning
Component Situation Solution
Window gla ss
Deposits Glass cleaner, then wipe dry
Decorative parts / Deposits Mild soap solutiona>
Trim
Pla sti c parts
Deposits Damp cl oth
Heavier deposits M ild soap solution al, detergent-free p lastic clean ing solu-
tion, if necessary
Di splay s/instru-Deposits Soft cloth with
LCD cleaner; dust in the lower area of the
ment cluste r instrument cluster can be removed using a soft brush .
Controls Deposits Soft brush, then a soft cloth with a m ild soap so lutiona >
Safety belts Deposits Mild soap solution al, allow to dry before letting them re-
tract
356

a co .... N ,....
N .... 0 0
3 co
Care and cleaning
Component Situation Solution
T ex til es
Deposits adhering to Vacuum cleaner
art ifici al leat her, the surface
A lcan tara Water-based deposits Absorbent
cloth and mild soap solutiona>
such as coffee, tea,
b lood, etc.
Oil -based deposits Apply a m ild soap solution
a), blot away the dissolved o il or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such
Special stain remover, blot with absorbent material, treat
as ink, nail polish, la- afterward with mild soap solution, if necessary
a)
tex paint, shoe pol-
ish, etc.
Natu ral le ath er Fresh stains Cotton cloth with a mild soap so lution a>
Water-based deposits Fresh stains: absorbent cloth
such as coffee, tea, Dried stains : stain
remover suitable fo r leather
b lood , etc.
Oi l-based deposits Fresh stains: absorbent cloth and stain
remover suitable
such as oil, make-up, for leather
etc. Dried stains : grease dissolving spray
Special deposits such Spot remove r suitab le for leather
as ink, nai l polish, la-
tex paint, shoe pol-
ish, etc.
Care Regularly apply condit ion ing c ream that protects from
lig ht and penet rates into the material. Use specia lly-co l-
ored conditioning cream, if necessary .
Carbon part s Deposits clean the same way as plast ic parts
a) Mi ld soap solution: maximum two tablespoons of neutral soap in 1 q uart (1 liter) of water
.8, WARNING
The windshield may not be trea ted with wa­
ter-repelling windshield coating agents. Un ­
favorable cond itions such as wetness, dark­
ness, or low sun can result in increased glare.
Wiper blade chatter is also possible.
@ Note
- Headlight s/tail li ght s
-Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcohol, because they could cause
cracks to form.
- Whe els
-
- Never use a ny pa int polish or other abra­
sive materials .
- Damage to the protect ive layer on the
rims such as sto ne ch ips or scratches must
be repaired immediately .
-Sen sor s/camera l enses
- Neve r use warm or hot water to remove
snow or ice from the camera lens . This
could cause the lens to crack .
- Neve r use ab rasive cleaning materials or
a lcohol to clean the camera lens . This
could cause scratches and cracks .
-Door window s
-Remove snow and ice on windows and ex-
terior mirrors w ith a plast ic scraper . To
357

Emergency assistance
Emergency assistance
General information
... Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tir e, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
... Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
_& WARNING
Follow the steps given above . This is for your
protection and the for the safety of other driv ­
ers.
Equipment
Vehicle tool kit/tire mobility kit/vehicle
jack
Applies to: vehicles with the vehicle tool kit, tire mobility kit
and veh icle jack
Applies to: sedan
Fig. 278 L uggage compartmen t: vehicle too l kit , ve hicle
j ack, tire mob ility kit an d comp resso r
Applies to: allroad
Fig. 279 Lug gage compa rtmen t: ve hicl e tool kit, v ehicle
j ack, tir e mobil ity k it and comp resso r
360
The vehicle tool kit, vehicle jack, tire mobility kit
and compressor are stored in the luggage com­
partment under the cargo floor cover.
Applies to: sedan
.,. Lift the cargo floor using the plastic handle and
hook the hand le onto the luggage compart­
ment
seal ~ fig. 2 78.
Applies to: allroad
... Remove the cargo floor cover ~ fig. 279 .
Applies to : vehicles with spare tire
... Remove the handle by turning it counter-clock ­
wise and remove the spare tire.
Appl ies to: sedan
.,. Unhook the cargo floor before closing the lug-
gage compartment lid .
Depend ing on vehicle equipment, the vehicle tool
kit, tire mobility kit and compressor may be lo­
cated under another cover that is secured w ith a
handwheel.
Applies to : allroad
On some vehicles, the vehicle tool kit is located
directly under the cargo floor
cover@~ fig. 2 79
behind the rear bench seat.
_& WARNING
Impr oper use of the vehicle jack can cause se­
rious personal injur ies.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if you
use the hex head, potentially causing an ac­
cident.
- The factory-supp lied jack is intended only
for your vehicle mode l. Under no circum­
stances should it be used to lift heavy
veh icles or other loads; you risk injuring
yourself.
- Never start the engine when the vehicle is
raised, which cou ld cause an accident.
- Support the vehicle securely with appropri­
ate stands if work is to be performed under­
neath the vehicle; otherwise, there is a po­
tential risk for injury.

Emergency assistance
"'Secure the collapsible spare tire with the hand -
whee l.
"'Fo ld the cargo floor cover back into p lace.
Snow chains
Using snow chains on the collapsible spare tire is
not permitted for technical reasons.
If you have to drive with snow chains and a front
tire fa ils, mount the collapsible spare tire in
p la ce of a rear tire. Insta ll the snow cha ins on the
rear tire that you removed, and install that in
p lace of the front tire that failed.
A WARNING
-
- Only use the collapsible spare tire in emer ­
gencies and drive very carefully, especially if
it is more than six years old .
- The compressor and the hose can become
very hot during operation which increases
the risk of burn injuries.
- After installing a collapsible spare tire, the
t ir e pressure must be checked as quickly as
poss ible to reduce the risk of an acc ident.
- Do not drive faster than 50 mph (80 km/h)
with a collapsible spare tire. Driving faster
than that increases the risk of an accident .
- Avoid full-throttle acceleration, heavy brak­
ing, and fast cornering with the collapsible
spare tire, because this increases the risk of
an accident .
- Never drive using more than one collapsible
spare tire, because this increases the risk of
an accident.
- Normal tires or winter tires must not be
mounted on the collaps ible spare tire rim.
«J:) Note
The compressor must be switched off after 12
minutes at the most to reduce the risk of
overheating . Let the compressor cool down
for several minutes before using it again.
368

Fuses and bulbs
Fuses
Replacing fuses
A fuse that has blown will have metal strips tha t
have burned through .
Fig. 289 @ Driver footwell (left -hand drive vehicle) : foot ­
res t,@ Front passe nge r footwell (right -hand drive vehicle ):
cove r
Fuses and bulbs
Fig. 290 © Driver's s ide o f the cockp it (left- han d drive ve­
hicle/r ight -h and drive vehicle): cove r, @ Left side of lu g·
gage compartment: cove r
The fuses are located in the footwell under the
foot rest (left-hand drive
vehicle)@¢ fig. 289 or
behind the cover (right-hand drive vehicle) @.
Additional fuses are located on the front side of
the cockpit (driver's
side) ©¢ fig. 290 and under
the left cover in the luggage compartment @.
.. Switch the ignition and all electrical equipment
off.
"Check the following table to see wh ich fuse be·
longs to the equipment.
" Remove the screwdriver and the reversible Torx
bit from the vehicle tool
kit ¢ page 360 .
.. Remove the foot rest or the corresponding cov­
er.
" Remove the colored plastic clip from the fuse
panel, if
necessary ¢ page 370, fig . 291. You
can dispose of the plast ic clip .
.. Remove the clamp from the rear side of the
cover @.
" Remove the fuse using the clamp .
" Replace the blown fuse only with an identical
new one .
" Reattach the footrest or the cover .
369

a co .... N ,....
N .... 0 0
3 co
Fuse panel © (brown)
4 Audi side assist
8 Smart module (tank)
11 12 Volt battery
12 Homelink
13 Rearview camera, peripheral cameras
14 Right tail lights
16 Right safety belt tensioner
Fuse panel © (red)
No . Equipment
2 Sound-amp
lifier
3 AdBlue heating
5 Trailer hitch (right light)
7 Trailer h
itch
8 Trailer hitch (left light)
9 Trailer h itch (socket)
10 Sport differential
11 AdBlue heating
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace any bulbs for
you.
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re­ moved before you are able to get to the bulb.
This applies especially to the light bulbs in the
front of your car which you can only reach
through the engine compartment.
Sheet metal and bulb holders can have sharp
edges that can cause serious cuts, parts must be
correctly taken apart and then properly put back
together to help prevent breakage of parts and
l ong term damage from water that can enter
housings that have not been properly resealed.
For your safety, we recommend that you have
your author ized Audi dealer replace any bulbs for
you, s ince your dealer has the proper tools, the
correct bulbs and the expert ise.
Fuses and bulbs
Gas discharge lamps (Xenon lights) :
Due to the high e lectr ical voltage, have the bulbs
replaced by a qualified technician. Headlights
with Xenon light are identified by the high volt­
age sticker .
LED headlights*
LED headlights require no maintenance. Please
contact your authorized Audi dealer if a bulb
needs to be replaced .
.&, WARNING
Changing Xenon lamps without the necessary
equipment can cause serious personal injury.
- Bulbs are pressurized and can explode when
be ing changed. Potential risk of injury!
- On veh icles equipped with gas discharge
bu lbs (Xenon light) life-threatening injuries
can resu lt from improper handling of the
h ig h-vo ltage portions of such lamps!
- Only your authorized Audi dealer or quali­
fied workshop should change the bulbs in
gas discharge lamps. There are parts with
sharp edges on the openings and on the
bulb holders that can cause serious cuts. If
you are uncertain about what to do, have the work performed by an authorized Audi
dealer or qualified workshop. Ser ious per­
sonal injury may result from improperly per­
formed work.
(D Tips
- If you st ill prefer to replace the light bulbs
yourself, be aware that the engine compart­ ment is a hazardous area to work
in¢ A in
Working in the engine compartment on
page 323.
- It is best to ask your authorized Audi dealer
whenever you want to change a bulb .
373

Technical data
Vehicle specifications
F ig. 302 W indshield (front left): Ve hicle Ident ification
Number (VIN)
XXXXX XX -X -XX XX X XX XX
CD+ ~t :1 :: xxxxxxxx xx x x x xxx xxx
TVP/fffl XXX XXX
XX XXXXXXX XX X X XX
XXX
KW XXX
®i ~:J ·f lfils~~ XXXX XXX XXX
®-+ ~N:a=i~l xxxx ; xxxx xx x ; xx
11. • AUSS, I OPTIONS
E0 A
7D 5 4UB 6
XM 5SG 5R W
2E H
J0Z lL B l
A S lB A
3FC SM U 7Xl
F 0 A 9G3 0G7 0YH 0JF
TL 6 3KA 8EH UlA X 98 Q Z7
lXW 803 908 824 020
7T6 C V7 7 K0 4 X3 2K2
3L4
4KC 3Y0 413
502
lSA 7GB 01 A 4G0
XX . X XX X XX X xxxx
Fig. 303 Vehicle identification label
Vehicle Identification Number (VIN) in the
Infotainment system
• Select in the Infotainment system: the I MENU I
button > Vehicle > left control button > Service
& checks> Vehicle information .
Vehicle Identification Number (VIN)
The VIN can be found in the Infotainment sys­
tem, on the vehicle data label, and under the
windshield on the front left side*
q fig. 302 . The
VIN is also in the right side of the luggage com­
partment.
Technical data
Vehicle identification label
The vehicle identification label ¢ fig. 303 is locat­
ed in the luggage compartment under the cargo
floor cover .
T he information of the vehicle identif ication label
can also be found in your Warranty
& Mainte­
nance booklet.
The sticker contains the follow ing vehicle data:
(D Vehicle Identification Number (VIN)
@ Vehicle type, eng ine output, transm ission
@ Engine and transmission codes
@ Paint and interior codes
® Optional equipment numbers
Safety compliance sticker
The safety compliance sticker is your assurance
that your new vehicle complies w ith all applicable
Federal Motor Vehicle Safety Standards which
were in effect at the time the vehicle was manu­
factured. You can find this sticker on the driver's
side B -pillar respect ively on the front end of the
driver's door.
It shows the month and year of
production and the vehicle identification number
of your veh icle (perforation) as well as the Gross
Vehicle Weight Rat ing (GVWR) and the Gross
Axle Weight Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in the
engine compartment next to the engine hood re­
lease. The spark ignition system complies with
the Canadian standard ICES-002 .
Notes about technical
data
The values may vary based on special equipment
as well as market-specific equipment and meas­
uring methods.
Please note that the specifications listed in the
vehicle documentation a lways take precedence.
0) Tips
Missing technical data was not available at
the time of pr int ing.
379

Tech nical data
Weights
Gross V ehicl e We ight Rat ing
The G ross Vehicle Weight Ra ting (GVWR), and
the Gross Axle Weight Rating (GAWR) for front
and rear are listed on a sticker on the driver's side
B-pillar respective ly on the front end of the driv­
er's door.
The G ross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank, oil
and coolant, plus maximum load, which includes
passenger weight (150 lbs/68 kg per designated
seating position) and luggage
we ight¢ &..
Gros s Ax le Weight Rating
The Gross Axle Weight Rating is the maximum
load that can be applied at each axle of the vehi­
cle¢&_ .
Vehicle c apacity w eight
The vehicle capacity we ight (max . load) is listed
on the driver 's side B -p ill ar respectively on the
front end of the driver's door.
_& WARNING
-The actual Gross Axle Weight Rating at the
front and rear axles should not exceed the
permissible weights, and their comb inat ion
must not exceed the Gross Veh icle Weight
Rating.
- Exceeding permiss ible weight ratings can
result in veh icle damage, acc idents and pe r­
sonal i njury .
Dimensions
(D Note
-The veh icle capacity weight figures apply
when the load is d istr ibuted evenly in the
vehicle (passengers and luggage). When
transport ing a heavy load in the luggage
compartment, carry the load as near to the
rea r axle as possible so that the ve hicle's
hand ling is not impaired .
- Do not exceed the maximum perm iss ible
axle loads or the maximum gross veh icle
we ight. Always remember that the ve hicle's
hand ling will be affected by the extra load.
Th erefore, a djust your speed acco rdingly.
- Always observe local regulations.
Length (in (mm )) Width (in (mm ))
Width across the Height at curb
mirrors (in (mm )) weight (in (mm))
A4 sedan 186.1 (4,726) 72.5 (1,842) 79.6 (2,022) 56.2 (1,427)
54 sedan 186
.8 (4,745) 72 .5 (1,842) 79 .6 (2,022) 55 .3 (1,404)
all road 187.0 (4,750) 72.5 (
1,842) 79.6 (2,022) 58.8 (1,493)
380