jack points AUDI A4 CABRIOLET 2009 Owners Manual

_____________________________________________ W_ h _a_t _ d_ o_ l _d _o _ n_o_ w_ ?_ . _ ..... 19111
•
& WARNING (continued)
pressure table - risk of accident! Use the highest tire pressure in
the table.
• Do not drive faster than 50 mph (80 km/h) - risk of accident!
• Avoid full-throttle acceleration, sharp braking, and fast
cornering - risk of accident!
• Never drive using more than one space-saving spare wheel -
risk of accident!
• Normal summer or winter tires must not be fitted on the space­
saving spare wheel rim. •
Wheel change
Before changing a wheel
Follow these points for your own and your passenger's
safety when replacing a wheel.
-After you experience a tire failure, pull the car well away
from moving traffic and try to reach level ground before
you stop => & .
- All passengers should leave the car and move to a safe
location (for instance, behind the guardrail)=>& .
- Apply the parking brake firmly=>&.
- Move selector lever to position Pon an automatic trans-
mission; put manual transmission in first gear =>& .
- If you are towing a trailer: unhitch the trailer from your
vehicle.
- Take the tool case and the spare tire=>
page 290 out of
the luggage compartment.
& WARNING
You or your passengers could be injured while changing a wheel if
you do not follow these safety precautions:
• If you have a flat tire, move a safe distance off the road. Turn off
the engine, turn the emergency flasher on and use other warning devices to alert other motorists .
• Make sure that passengers wait in a safe place away from the
vehicle and well away from the roadway and traffic.
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed. When one
front wheel is lifted off the ground, placing the Automatic Trans­
mission in "P" (Park), or engaging a gear in a manual transmission
will
not prevent the vehicle from moving .
• Before you change a wheel, be sure the ground is level and firm.
If necessary, use a sturdy board under the jack.
• After installing the spare wheel, make sure that you remount
the flat tire/wheel in its storage area properly and tighten the
knurled retaining screw securely. •
Changing a wheel
When you change a wheel, follow the sequence described
below step-by -step and exactly in that order.
1. Remove the decorative wheel cover*. For more details
see also =>
page 294, "Decorative wheel covers" or
=>
page 295, "Wheels with cap-covered wheel bolts".
2. Loosen the wheel bolts=>
page 295.
3. Locate the proper mounting point for the jack and align
the jack below that point=>
page 296.
4. Lift the car with the jack=> page 296. _,..
Do-it-yourself service

11111...__W_ h_ a_ t_d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
& WARNING
• Using force without control to speed the wheel change up can
cause the vehicle to slip off the jack and cause serious personal
injuries.
• Do not loosen the wheel bolts more than one turn before you
raise the vehicle with the jack. -Risk of injury!
[ i ] Tips
• Never try and use the hexagonal socket in the handle of the
screwdriver to loosen or tighten the wheel bolts.
• If a wheel bolt sits very tight, you may find it easier to loosen by
carefully pushing down on the end of the wheel bolt wrench with
one foot only . As you do, hold on to the car to keep yourself stable
and take care not to slip.•
Raising the vehicle
The vehicle must be lifted with the jock first before the
wheel con be removed.
N
"' ~ I
"' al
Fig . 219 Wheel
change : mounting
points for the lifting
jack Fig
. 220 Close-up:
proper positioning of
lifting jack
- Position the jack below the door sill under the mounting
point
that is closest to the wheel to be changed
~ fig. 219.
- Turn the
jack handle clockwise until the jack arm just fits
underneath the rib running along the underbody
~ &,.
- Align the jack so that the jack arm claw~ fig. 220 @fits
snugly around the underbody rib and the movable base
plate ® sits flat on the ground.
- Wind the jack up further until the flat wheel comes off the
ground~ &-
Recesses at the front and rear of the underbody rib mark the proper
mounting locations for the jack => fig. 219. There is only one desig­
nated jack mounting point for each wheel. Do not apply the jack
anywhere else=>& .
The jack should be positioned approximately 6 in. (15 cm) behind
the front wheel or 10 in. (25 cm) in front of the rear wheel.
An
unstable surface under the jack can cause the vehicle to slip off
the jack . Always provide a firm base for the jack on the ground. If
necessary place a sturdy board or similar support under the jack. On
hard, slippery surfaces (such as tiles) use a rubber mat or similar to
prevent the jack from slipping=>& . .,,

111'1...__E_ m_ e_ r -'g==-- e_n _c_ y=---- s_ i_ t _u _a _ t_ i_o _n _ s _____________________________________________ _
Loading the vehicle onto a flat bed truck
Front hook up
I
"' m
Fig . 229 Ve hicle on flat
b ed tru ck
- Align the vehicle w ith the centerline of the car carrier
ramp .
- Attach the winch hook to the front towing loop previously
installed .
Rea r hook up
-Align the vehicle wi th t he centerline of the ca r carrier
ramp .
- Attach the winch hook to the rear towing loop previously
i nstalled.
[ i ] Tips
Check careful ly to make sure the hook -up is secure before moving
the car up the flatbed truck ramp. •
Lifting vehicle
Lifting with workshop hoist and with floor
jack
T he vehicle may only be lifted at the lifting p oints illus­
trated.
- Read and heed WARNING =>& .
m 9 :r
"' m
Fig . 2 30 F ront lift in g
po in t
F ig . 2 3 1 Rear lift in g
po int
- Locate lifti ng poi nts =:> fig. 230 =:> fig. 23 1.
- Ad just li fting arms of works hop hoist or floor jack to
match vehicle l ifting points.

________________________________________________ E _m_ e_r.:g :;,. e_ n_c ...: y:.- s_ i_ t _u _a_ t_ i_ o _ n_ s ____ fflll
•
- In se rt a rubber pad betwee n th e floor jack/ wo rk sh op
h oi st and the li ftin g p oin ts .
If you must lift your vehicle with a floor jack to work underneath , be
sure the vehicle is safely supported on stands intended for this
purpose .
Fr ont lifting point
The lifting poi nt is located on the floo r pan rei nforceme nt about at
the same leve l as the jack mounting point~ page
308, fig. 230. Do
not lift the vehicle at the vertical sill reinforcement.
Rear lifting point
The li ftin g point is locate d on t he vert ical re inforceme nt of th e low er
sil l for the on board jack~ page
30 8, fig. 23 1.
Lifting with vehi cle ja ck
Refer to
~ page 296.
& WARNING
• To reduce the ri sk of serious injury and vehicle damage.
- Always l ift the vehicle only at the special workshop hoist and
floor jack lift points illustrated
~ page 308 , fig. 230 and
~ page 308, fig. 231.
- Failure to lift the vehicle at these points could cause the
vehicle to tilt or fall from a lift if there is a change in vehicle
weight distribution and balan ce . This might happen , for
e xample , when heavy components such as the engine block or
transmission are removed .
• When removing heavy components like these, anchor vehicle
to hoist or add correspond ing we ights to maintain the center of
gravity. Otherwise , the vehicle might tilt or slip off the hoist ,
causing ser ious personal injury .
0 Note
• Be aware of the fo llowing po ints be fore l ifting the ve hicle:
- The vehicle should never be lifted o r ja cked up from under ­
neath the engine oil pan , the tran smis sion housing , the front or
rear a xle or the body side members. This could lead to serious
damage.
- To avoid damage to the underbody or chassis frame , a rubber
pad must be inserted between the floor jack and the lift points .
- Before dr iving over a workshop hoist , check that the vehicle
weight does not exceed the permis sible lifting capacity of the
hoist .
- Before driving over a workshop hoist , en sure that there i s
sufficient clearance between the hoist and low parts of the
vehicle. •
Do-it-yourself service