fuel AUDI A5 CABRIOLET 2010 User Guide

1111....__w __ a _r_ m __ a_n_ d_ c_ o _ l_d _______________________________________________ _
Applies to veh icles : wi th d eluxe automat ic clim ate cont rol pl us
Economical use of the climate control
system
Economical use of the climate control system helps save
fuel.
When the climate control system is working in cooling mode,
engine performance is reduced and fuel consumption is
affected. To keep the time the climate control system is on as
short as possible, you should do the following:
- To save fuel, turn off cooling mode by pressing the AC
button (indicator light goes out).
- In addition, if you open the window while driving, turn off
cooling mode by pressing the AC button (indicator light
goes out).
- If the vehicle is extremely hot due to the heat of the sun,
briefly open doors and windows.
~ For the sake of the environment
When you save fuel, you reduce emissions from the vehicle. •
Applies to vehicles: with deluxe automatic climate cont rol plus
Deluxe automatic climate control plus -
basic settings
The basic climate control settings can be adjusted in the
radio or MM!*.
-Select: Function button (CAR]> Climate control switch.
Automatic recirculation
An air quality sensor detects increased concentrations of pollutants
in the outside air and automatically switches to recirculation mode. We recommend that you always keep automatic
recirculation ON to
prevent polluted outside air from entering the vehicle interior.
If the
air quality sensor located in the climate control system detects
polluted outside air, the sensor decides whether the air pollution can
be reduced by the factory-installed pollutant filter or whether it is
necessary to switch to recirculation. With heavy concentrations of
pollutants, the climate control system is switched automatically to
recirculation mode and the supply of outside air is blocked. As soon
as the concentration of pollutants in the outside air drops, fresh air is
supplied to the vehicle interior again.
In the event that the windows fog up during automatic recirculation,
press the
l@I button immediately.
Under certain operating conditions, automatic recirculation is
switched off automatically. When outside temperatures are below
about 50
°F ( + 10 °(), automatic recirculation is limited to
30 seconds. When outside temperatures are below about 30
°F (-
1 °C), automatic recirculation is limited to 15 seconds .
Synchronization
After Synchronization is set to on, all of the subsequent climate
control settings (except for seat heating*) for the driver are trans­
ferred to the front passenger .
Synchronization is canceled when settings are adjusted on the front
passenger's side .•

Transmission -
----------------
- Step on the brake peda l. At the same time press and hold
the interlock button on the s ide of the gear selector knob
=:> fi g. 153 wi th your thumb until you have moved the
selector lever to the des ired position .
Automatic selector lever lock
The se lector lever is locked in the P and N positions w hen the ignition
is turned on . To move the leve r from these pos it ions the driver must
dep ress the brake peda l. As a reminder to the d river, the following
warning appears in the instrument cluster display when the se lector
is in
P and N:
When stationary apply footbrake while selecting gear
A time delay e lement prevents t he selector leve r from lock ing when
it is moved throug h the
N posit ion (going from R to D ). The lock ing
element will lock the se lector lever if the lever is left in N (Neutra l) for
more tha n app rox imately 1 second, w ithout t he b rake pedal be ing
pressed.
A t speeds above about 3 mp h (5 km/h) the A utomat ic Shi ft Lock is
automatically deactivated in t he
N position .
Interlock button
The lock button on the selector lever prevents the lever from being
a cciden tally shifted in to cert ain posi tions . Pressing this b utton deac­
tivates the selector lever lock. Depend ing on the direction of the
shift, the se lector leve r locks a t different positions. The pos itions are
highlighted in the illustrat io n =>
page 150, fig. 153 .
Igni tion key safety interlock
The key cannot be removed from the ignition unless the selector lever
is in the
P pa rk position. When the igni tion key is removed, the
selector lever will be locked in the
P position. •
Controls and equip ­
ment Safety first
Applies
to vehicles : with au toma tic transmiss ion
Kick-down
The kick -down feature allows the vehicle to generate
maximum acceleration .
When you press the accelerator peda l beyond the resis tance po int
that is reached at full throttle, the transmission will select a lower
gear rat io b ased on vehicle speed and e ngine RPM . The engine R PM
will be controlled to produce maximum vehicle acceleration as long
as you con tinue to press the acceler ator pedal beyond t his resistance
point .
& WARNING
Be careful when using the kick-down featu re on slippery roads.
Rapid a cceleration may cau se the vehicle to skid .•
App lies to veh icles: with automatic trans mission
Dynamic shift program (DSP)
The automati c transmi ssion is electronically controlled .
The transmiss ion is self adapting and will automatically select the
bes t sh ift p rogram su ited to the dr iv ing cond it io ns and dr iving style .
Th e transmission will select one of the
economy programs when you
drive at a steady speed or a gradually c hanging speed without heavy
acce le ration . This ac hieves optimum fuel efficiency, with early
upshifting and delayed downshifting.
Th e transm iss ion will au tomatically se lect the
s porty shift p rograms
when you dr ive at higher speeds, or w ith heavy acceleration and
frequently chang ing speeds . Upshifts a re de layed to make full use of
engine power . Downs hifting takes place at higher engine speeds than
in the economy programs . _.,
Vehicle care Technical data

-Transmission .n,..__ ______________ _
The selection of the most suitable shift program is a continuous,
automatic process. The driver can also make the transmission switch
to a sporty program by
quickly pressing down the gas pedal.
This causes the transmission to shift down to a lower gear to achieve
rapid acceleration, e .g . for quickly passing another vehicle. You do
not need to press the gas pedal into the kick-down range. After the
transmission has upshifted, the original program is selected
according to your driving style.
An additional shift program allows the automatic transmission to
select the proper gear for uphill and downhill gradients.
This keeps the transmission from shifting up and down unnecessarily
on hills. The transmission will shift down to a lower gear when the
driver presses the brake pedal on a downhill gradient. This makes use
of the braking effect of the engine without the need to shift down
manually. •
Applie s to veh icles: w it h au tomatic transm iss io n
Manual shift program
Using the manual shift program you con manually select
gears.
Fig. 154 Center
console: shifting the
tiptronic ® manually
Fig. 155 Display:
manual shift program,
selected gear high­
lighted
Switching to manual shift program
- Push the selector lever to the right from D. As soon as the
transmission has switched over, the selected gear appears
in the display.
To upshift
-Push the selector lever forward to the plus position 0
~ fig. 154.
To downshift
- Push the lever to the minus pos ition Q .
When accelerating, the transmission will automatically shift into the
next gear before the engine reaches its maximum RPM.
If you apply a light throttle when accelerating, tiptronic ® will auto­
matically shift from 1st to 2nd gear to save fuel. If you apply a heavy
throttle, the transmission will stay in 1st gear until near maximum
RPM is reached, or until the driver shifts into 2nd gear.
If you take your foot off the accelerator pedal when driving down a
steep incline, tiptronic ® will downshift from the selected gear into
the next lower gear until it reaches 1st gear, based on road speed and
eng ine RPM. Automatic downshifting is interrupted as soon as you
app ly the throttle again. _.

Transmission Ill _______________ ___.
multitronic®
Applies to vehicles: with mult it ro nic ® Continuously Variable T ransmiss ion (CVT)
General information
Your vehicle is equipped with a electronically controlled continuous ly
var iable transmission (multitronic ®). Inside the multitronic ® system,
the gear ratios are not shifted in finite steps as in a conventional auto­
matic transm ission, but rather
continuously. As a result, engine
power is applied smoothly and comfortably, and better fuel economy
is achieved.
The transmission selects the appropriate gear ratio (upshifts and
downsh ifts) automatically based on set driving programs
=> page 159, "Dynamic shift program (DSP)" .
You can also manually select a shift program (tiptronic ®)
=> page 159 .
You should note, that the multitronic transmission differs from a
conventional Automatic Transmission. In the multitronic transmis ­
sion the engine power is transferred via a link-plate chain, rather than
by a conventiona l torque converter . The multitronic transmission
great ly reduces vehicle "creep" when at a standstill and the transmis­
sion is in
D Sor R. •
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Applies to vehicles : with multitronic® Continuously Variable Transmission (CVT)
Driving the multitronic ®
The gear ratio is continuously adopted to vehicle speed
and load.
Starting the engine
- The selector lever must be in N or P.
Starting off
- Press and hold the brake pedal.
Fig. 159 Section of
the center console:
sel ector lever with lock
button
- Press and hold the release button in the selector lever
handle and move the selector leve r from
P (alternatively
N ) to D (alternatively S) and release the button.
- Wait briefly until the transmission has shifted (you will
feel a slight movement).
- Remove your foot from the brake pedal and accelerate
=> &.
Rocking back and forth to become unstuck
- Shift only between D and R when the vehicle is at a full
stop and the engine is running at idle speed.
Vehicle care Do-it-yourselt service iTechnical data

____________________________________________________ T _r_a _n_ s_m _ i_s _s_ i_ o _ n _ ___._
& WARNING
Be careful when using the kick-down feature on slippery roads.
Rapid acceleration may cause the vehicle to skid.•
Appli es to vehi cles: wit h mul tit ro nic ® Con tin uousl y Va riable Tra ns mi ssion (CVT )
Dynamic shift program {DSP)
The multitronic ® transmission is electronically
controlled.
The transmission selects the appropriate gear ratio (upshifts and
downshifts) automatically based on preset driving programs.
The transmission will select one of the
economy programs when you
drive at a steady speed or a gradually changing speeds without heavy
acceleration . This gives best fuel efficiency, with early upshifting and
delayed downshifting .
The transmission will automatically select the
sporty shift programs
when you drive at higher speeds, or with heavy acceleration and
frequently changing speeds . Upshifts are delayed to make full use of
engine power . Downshifting takes place at higher engine speeds than
in the economy programs.
The selection of the most suitable shift program is a continuous,
automat ic p rocess . The driver can also make the transmission switch
to a sporty program by
quickly pressing down the gas pedal.
This causes the transmission to shift down into a lower gear ratio and
makes quick acceleration possible (to pass another vehicle) You do
not need to press the gas pedal into the kickdown range . After the
transmission has upshifted, the original program is selected
according to your driving style.
An additional shift program allows the automatic transmission to
select the proper gear for uphill and downhill gradients.
This prevents the transmission from shifting up and down unneces­ sarily on hills. The transmission will shift down to a lower gear ratio
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
when the driver presses the brake pedal on a downhill gradient . This
makes use of the braking effect of the engine without the need to
shift down manually.
If you are driving in h ills and mountains, the transmission will contin­
uously adjust the gear ratio to the road grade. If you press the brake
pedal when driving downhill, the transmission will downshift auto­
matically. This increases the braking effect of the engine.
If the cruise control is on when you are traveling downhill, the trans­
mission will automatically select a lower gear ratio in order to main ­
tain the set vehicle speed. This will cause the engine speed to
increase. •
App lies to veh icle s: with m ult itr on ic ® Contin uous ly Va riabl e Tra nsmi ssion ( CVT)
tiptronic ® manual shift program
Using the manual shift program (tiptronic ®) you can
manually shi~ between seven pre-programmed gear
ratios (transmission positions).
Vehicle care
Fig . 162 Center
console: shifting
manually
Do-it-yourselt service iTechnical data

ffl..__T_ r_a _n_ s_ m_ is_ s_io _ n ___________________________________________________ _
Fig. 163 Display:
manual shift progra m,
selec ted gear
Switching to manual shift program
- Push the selector lever to the right from D. As soon as the
transmission has switched over, the selected gear appears
in the display~ fig. 163.
To upshift
-Push the selector lever forward to the plus position
~ page 159, fig. 162 G).
To down shift
- Push the lever to the minus position Q.
When accelerating , the transmission will automatically shift into the
next higher gear before the engine reaches the maximum RPM.
Wh en accelerating, if you apply a light thrott le, the tiptronic ® will
automatically shift into the next higher gear to save fuel. If you apply
a heavy throttle, the transmission will stay in gear engaged until near
maximum RPM are reached, or until the driver manua lly shifts into a
higher gear.
If you take your foot off the accelerato r pedal when driving down a
steep incline , the tiptronic ® will downshift from the selected gear
into the next lower gear based on road speed and engine RPM. The
automatic downshifting is interrupted as soon as you apply throttle
again .
[I] Tips
• When you shift into the next lower gear, the engine w ill downshift
only when there is no possibility of over-revving .
• When the kick-down comes on, the transmission will sh ift down to
a lower gear depending on vehicle and engine speeds.
• The tiptronic ® is inoperative when the transmiss ion is in the fail­
safe mode .•
Applies to vehicles: with mult itron ic ® Cont inuously Variable Transm ission (CV T)
Steering wheel with tiptronic ®
The shift buttons on the steering wheel allow the driver to
shift gears manually.
Fig . 164 Steering
w hee l: Shift buttons
- To downshift, touch the button on the left Q.
- To upshift, touch the button on the right G).
The shift buttons are activated when the selector lever is in D, Sor in
the manual shift program (tiptronic).
Of course, you can continue to use the manual shift program with the
selector lever on the center console . •

________________________________________________ D_ r_ i_ v _i_n _,,,g "-- S_a_ f_ e_ l _,,y'-- __
& WA RNING (continued)
to get out . Being trapped in a vehicle can lead to serious personal
injury .
• Never let children play in or around the vehicle.
• Never l et passengers ride in the luggage compartment. Vehicl e
occupants must alwa ys be p roperl y res trained in one of the
vehicle 's seat ing posi tions.
(I) Tips
• Air circula tion helps to reduce window fogging. Sta le air escapes
to the outside thro ugh vents in the tr im panel. Be sure to keep these
slots free and ope n.
• Th e tire p ressure m ust co rrespon d to the load . The tire pressure is
show n on the tire p ressu re label. O n USA v ehicles, the tire p ress ure
label is located on the driver's side 8-p illar. On Canada veh icles, the
ti re pressu re lab el is locat ed either on the driver' s sid e B-pillar or
inside the fuel fi lle r flap . The t ire pressure labe l lists the recom ­
mended co ld tire in flati on press ures f or th e ve hicle at its max imum
capacity weight and the tires that were on yo ur vehicle at the time it
w as m anuf acture d. F or re co m mended ti re p res sur es for normal loa d
conditions, p lease see chapter=>
page 300 . •
Tie-downs
T he l uggage c omp artm ent is equipped with fo ur tie­
d ow ns to sec ure l ug gag e a nd oth er ite ms.
Use the t ie-downs to secu re yo ur cargo properly => page 183,
"Lo ading the lugg age comp artmen t" .
I n a co llision, t he laws of physics mean that ev en sma ller items that
are loose i n the vehicle will become heavy missiles t hat can cause
serious injury. Items in the vehicle possess e nergy wh ich vary w ith
vehicle speed and the we ight of the item. Vehicle spee d is t he most
signifi cant factor.
Controls and equip­
ment Safety first Vehicle operation
For example,
in a frontal collis io n at a speed of 30 mph (48 km/ h),
t he forces a ctin g o n a 1 0-lb (4 .5 kg) objec t are ab out 20 times the
normal weight of the item . T his means that the weight of the item
wou ld s udden ly be abo ut 200 lbs . (90 kg). You can imagine the inju­
ries that a 200 lbs . (90 kg) item fly ing freely through the passenger
compartment could cause in a collision like this .
& WARNING
Weak, damaged or improper straps used to secure item s to tie­
downs can fail during hard braking or in a collision and cause
serious personal injury.
• Always use suitable mounting straps and properly secure items
to the tie -downs in the luggage compartment to help prevent
items from shifting or flying forward as dangerous missiles.
• When the rear seat backrest is folded down, always us e suit­
able mounting straps and properly secure items to the tie-downs
in the luggage compartment to help prevent items from flying
forward as dangerous missiles into the passenger compartment .
• Never attach a child safety seat tether strap to a tie-down .•
Reporting Safety Defects
Applicable to U.S.A.
If you believe that your vehi cle has a defect
whi ch could cause a crash or could cau se injury
or death, you should immediately inform the
National Highway Traffic Safety Administration
(NHTSA) in addition to notifying Audi of
Ameri ca, Inc. -.
Vehicle care Do-it-yourself service Technical data