display AUDI A5 CABRIOLET 2015 Service Manual

Audi drive select
sporty shifting characteristics . The S gear
position engages automatically.
- In vehicles that have dynamic steering*, op­
erating noise is heard when starting or stop­
ping the engine. This does not indicate a
problem.
Selecting the driving mode
Applies to veh icles: with Audi drive select
You con choose between Comfo rt, Auto , Dynam·
ic
and Individual * modes.
N N 0
0
'I::======:..,. gJ
drive I sel,.c,ct _ J -~-
F ig. 119 Cente r conso le: Control fo r Aud i drive se lect
Fig . 120 MMI*: A udi drive select
Adjusting the Individual mode
Applies to vehicles: w ith MMI and Audi drive select
.,. To set the mode, press the~:/:'.~ button
r::!) fig. 119 multiple times until the desired
mode is displayed in the instrument cluster . Or
.,. In the MMI*, select: ICARlfunction button>
Comfort, Auto, Dynamic or Individual*.
In vehicles without the MMI*, the r:::~ button is
found underneath the shift/selector lever.
You can change the driving mode when the vehi ­
cle is stationary or while driving . If traffic per­
mits, after changing modes, briefly take your
foot off the accelerator pedal so that the recently
selected mode is also activated for the engine
and transmission .
Comfort -provides a comfort-oriented vehicle
setup and is suited for long drives on highways.
Auto -provides an overall comfortable yet dy­
namic driving feel and is suited for every day use.
Dynamic -gives the driver a sporty driving feel
and is suited to a sporty driving style .
Individual* -c>page 104 .
&_ WARNING
Pay attention to traffic when operating drive
select to prevent potential risk o f an acciden t.
You can personally specify the vehicle setup in the MMI* .
.,. Select the ICAR I function button > Set individu·
al
control button. Once you select the menu,
you w ill automatically drive in the
individual
mode.
Systems Comfort
Eng i ne/Tra nsm ission ba
lanced
Steering comfortable
Dynamic steering* comfortable/indirect
104
The equipment in your vehicle will determine
which settings you can adjust. The following ta­
ble prov ides an overview of the characteristics of
each driving mode.
Auto Dynamic
balanced sporty
balanced sporty
balanced/direct sporty/direct

Parking System
The rear acoustic park assist system is integrated
in the rear of the vehicle and the rear view cam­
era is integrated in the rear lid
c::> page 109.
A WARNING
-
- The rear view camera has blind spots, in
which objects cannot be detected. Be espe­
cially careful to check for small children and
animals before backing up. Small children and animals will not always be detected by
the sensors.
General Information
Applies to vehicles: with parking system (rear, with rear view
camera)
Fig. 123 Covered ar ea (D and uncovered area @ of the rea r
view came ra
Fig. 124 T runk lid: Location of the rear v iew camera
Sensors in the bumper
Sensors are located in the rear bumpers . If these
detect an obstacle, audible signals warn you . The
range at which the sensors begin to measure is
approximately:
To the side 2 ft (0.60 m)
Center rear 5.2 ft (1.60 m)
Distance warning when reversing starts when an
obstacle is detected in the range of the parking
108
assist system. As the distance decreases, the
time interval between the audible tones becomes
shorter.
When the distance is less than 1ft (0.30 m), the
tone becomes continuous. At this point you
should stop backing up.
If the distance to an obstacle stays the same, the
volume of the distance signal chime is gradually
reduced after about 4 seconds (does not affect
the continuous signal tone). Approaching anoth­
er obstacle will cause the distance signal to
sound again at the normal volume.
Rear view camera coverage area
The MMI display shows the area covered by the
rear v iew camera
c::> fig. 123 @. Objects that are
not in the area covered @are not shown on the
MMI display.
We recommend that you practice parking with
the rear view camera in a traffic-free location or
parking lot to become familiar with the system,
the orientation lines, and their function. When
doing this, there should be good light and weath­
er conditions.
In the MMI display, objects or vehicles appear
closer or further away if:
-you are driving in reverse gear from a level sur­
face onto an incline, or a downward slope,
- you are driving in reverse gear toward protrud­
ing objects,
- the vehicle is carrying too much load in the
rear.
The accuracy of the orientation lines and blue
surfaces diminishes if:
- the rear view camera does not provide a reliable
image, for example, in poor visibility conditions
or if the lens is dirty,
- the image on the screen is not visible due to sun glare and reflection .
Caring for the rear view camera lens
The rear view camera is located above the rear li­
cense plate bracket. For the parking assist to op-
erate, the lens
c::> fig . 124 must be kept clean : .,._

M N
ci u.. co ...... \!) 1.1'1
N 1.1'1 ......
-Dampen the lens with a househo ld alcoho l­
based glass cleaner, and clean the lens with a
dry cloth
¢ 0 .
- Remove snow with a hand brush and ice pref­
erably with a de-icing spray
¢0 .
A WARNING
- The parking aid cannot replace the driver's
attent ion. The driver alone is responsible for
park ing and s imilar driving maneuvers .
-Always keep your eyes on the veh icle's sur­
roundings, using the rear view m irror as
well.
- Do not allow yourself to be distracted from
traffic by the rear view camera pictures.
- If the posit ion and the installation ang le of
the camera has c hanged, for example, after
a rear end collision, do not continue to use
the system for safety reasons. Have it
checked by a qualified deale rship .
@ Note
-Low obstacles already signaled by a warning
can d isappear from the system's detection
range as they are approached and will not
continue to be signa led. Objects such as
barrier chains, tra ile r draw bars, thin paint­
ed vertical po les or fences may not be de­
tec ted by the sys tem, posing r isk of dam­
age.
- Never use warm or hot w ater to remove
snow or ice from the rear view camera lens -
danger of crack formation on the lens!
- When cleaning the lens, never use products
that are abrasive .
Switching on/off
Applies to vehicles: with parking system (rear, with rear view
camera)
The rear view camera switches on automatically
together with the acoustic park assist when you
put the vehicle in reverse.
Sw itching on
.,. Put the vehicle in reverse gear, the acoustic
parking system w ith rear view camera is act ivat ­
ed automat ica lly. Act ivat ion of the acoust ic
Parking Syste m
pa rking system is confirmed by a brief acknow l­
edgement so und.
Switching off
.,. Dr ive faste r than 9 mph (15 km/h) , or
.,. take the vehicle out o f reverse gea r. The aco us­
tic parking sys tem is immed iate ly deactivated,
and the rear view camera picture is deactivated
automatically after a period of about 15 sec­
onds, or
.,. sw itch
off the ignition.
The de lay in deact ivating the camera provides an
u ninterrupted view be hind the vehicle especia lly
when maneuvering in t ight parking spaces and
prevents the p icture from turning
off the every
time you shift out of reverse.
If the warning message appears in the display
but not the rear view camera p icture, read and
confirm the warning message . The acoustic d is­
tance signal is always active .
If you press a function button on the MMI contro l
console, the rear view camera picture disappears.
The rear v iew camera p icture reappears the next
time you park .
Furthe r information on the warning message and
the MMI contro l conso le can be found in the MMI
instruct ion booklet.
A WARNING
--
- On ly use the rearview camera to assist you if
it shows a good, clea r picture . For example,
the image may be affected by the su n shi n­
ing into the le ns, dirt on the lens o r if the re
is a defec t.
- Use the rea rv iew camera only with the rear
lid comple tely closed . Make sure any objects
you m ay have moun ted on the rea r lid do
not block the rearv iew camera .
(D Tips
-The rear view camera picture is available as
soo n as the MMI Di splay o r th e MMI is
switched on, or the s tart- up pha se is com ­
ple ted.
- The sensors m ust be ke pt clean and free of
snow and ice fo r the park ass ist to opera te.
109

Parking System
-You can change the volume and pitch of the
signals as well as the display
~ page 112.
-What appears in the display is time-delayed.
Reverse Parking
App lies to veh icles: w ith pa rking system (rea r, w ith rea r v iew
camera)
Parking mode 1 can be used when parking in a
garage or parking space.
Fig. 125 MM I Di splay: Aiming at a parking spot
Fig . 126 MMI Di splay: Al ignin g th e ve hicle
• Switch the MMI on and select the reverse gear.
• Turn the steering wheel until the orange orien ­
tation lines
(D appear in the parking spot
¢ fig. 125. Use the markings @to help you es­
timate the distance from an obstacle. Each
marking corresponds to 3
ft (1 m). The blue
area represents an extension of the vehicle's
outline by approximately
16 ft (5 m) to the
rear .
• While driving in reverse gear, adjust the steer­
ing wheel angle to fit the parking space with
the aid of the orange orientation lines ¢0 .@
marks the rear bumper. You should stop driving
in reverse as soon as and no later than when
the red orientation line @abuts an object
¢ _& !
110
A WARNING
- The rear view camera does not show the en­
tire area behind the vehicle¢
page 108,
fig . 123.
Watch out especially for small chil­
dren and animals . The rear view camera can­
not always detect them, posing risk of an
accident!
- Please note that objects not touching the
ground can appear to be further away than
they really are (for example, the bumper of
a parked vehicle, a trailer hitch, or the rear
of a truck). In this case, you should not use
the help lines to help with parking, which poses danger of an accident!
cg) Note
- Low obstacles already signaled by a warning can disappear from the system's detection
range as they are approached and will not
continue to be signaled. Objects such as
barrier chains, trailer draw bars, thin paint­
ed vertical poles or fences may not be de­
tected by the system, posing risk of dam­ age.
- In the MMI display, the direction of travel of the vehicle rear is represented depending on
the steering wheel angle. The vehicle front
swings out more than the vehicle rear. Main­
tain plenty of distance from an obstacle so
that your outside mirror or a corner of your
vehicle does not collide with any obstacles -
danger of accident!

M N
ci LL co
rl I.O
"' N
"' rl
Parallel Parking
Applies to vehicles: with parking system (rear, with rear v iew
camera)
Use parking mode 2 to help you park on the edge
of a street.
Fig. 127 MMI Display: blue surface in the park ing spot
Fig. 128 MMI Display : Blue curve on the curb
The following steps apply only when there is no
obstacle (such as a wall) near the parking spot.
Otherwise, please read the "Tips on Parking Next
to Obstacles"
c::> page 111.
.,. Activate the turn signal.
.,. Position your vehicle parallel to the edge of the
street, approx imately 3 ft (1 m) from a parked
vehicle .
.,. Switch the MMI on and se lect the reverse gear.
The parking aid turns on and parking mode 1
appears on the display.
.,. Press the
Mode c::> fig. 127 © control button on
the MMI contro l conso le. Parking mode 2 ap­
pears.
.,. Back up in reverse gear and align your vehicle
so that the blue area @borders on the rear end
of the vehicle or on the park ing spot line. The
blue area represents an extension of the veh i­
cle's outline by approximately 16 ft (5 m) to the
rear. The long side of the blue area should be
Parking System
on the curb. The entire blue area must fit into
the parking spot.
.,. While the vehicle is stationary, turn the steer­
ing wheel to the right as far as it will go.
.,. Back into the parking spot. Stop the vehicle as
soon as the blue curve touches the curb
<=:>fig. 128 .
.,. While the vehicle is stat ionary, turn the steer­
ing wheel to the left as far as it will go .
.,. Cont inue to back up into the parking spot until
the vehicle is parked parallel to the curb. @
marks the rear bumper. You should stop driving
in reverse as soon as and no later than when
the red orientation line© abuts an object
c::> ,&.! Keep an eye on the front of your veh icle
while doing this
<=:> CI) .
Parking next to obstacles
When there is an obstacle (such as a wall) next to
the parking spot, choose a spot with more space
on the sides. Position the long side of the blue
area so that there is sufficient space from the
curb. The area must not be on the curb. You will
also need to start turn ing the steer ing wheel
much earlier . There should be a sufficient amount
of space between the curb and the blue curve,
and the blue curve
c::> fig. 128 must not touch the
curb.
A WARNING
- The rear view camera does not show the en­
tire area behind the vehicle
<=:>page 108,
fig. 123.
Watch out especially for small chil ­
dren and anima ls. The rear view camera can­
not always detect them, pos ing risk of an
accident!
- Please note that objects not touching the
ground can appear to be further away than
they really are (for example, the bumper of
a parked veh icle, a trailer hitch, or the rear
of a truck). In this case, you should not use
the help lines to help with parking, which
poses danger of an accident!
(D Note
In the M MI dis play, the direction of travel of
the veh icle rear is rep resented depend ing on
the steering wheel angle. The vehicle front
111

Parkin g Sys tem
sw ings out more than the vehicle rear . Main ­
tain plenty of distance from an obstacle so
that your outside mirror or a corner of your
veh icle does not collide w ith any obstacles -
danger of accident!
(D Tips
The left or right orientation lines and surfaces
w ill be displayed, depending on the turn sig­
nal being used.
Adjusting the display and warning tones
Applies to vehicles: w ith parking system (rear, with rear view
camera)
The display and warning tones ore adjusted in
the radio or MMI*.
.. Se lect: ICARlfunct ion button> Parking sy stem .
Or
.. Se lect: ICAR I function button> Car system s*
control button > D riv er a ss is t> Par king aid .
D isplay
- Off -when the pa rking system is switched on,
o nl y aud ible signals are given.
- On -when the pa rking system is switched on,
the p icture from the rear view camera is dis­
played.
Warning tones
- Rea r volume -
rear sensor volume
-Rear frequenc y -rear sensor frequency
- Music volume wh ile pa rking -when the pa rk-
ing system is switched on, the volume of the
active aud io source is lowered .
The newly adjusted value is briefly heard from
the signal generator. The settings are automati­
cally stored and assigned to the remote control key .
A WARNING
- Always make sure that the volume and fre ­
quency of the wa rning tones is adj usted so
that you can eas ily hear the acoust ic dis­
tan ce signal even if the radio is p laying, the
air-con ditione r blower is on High or t here is
a high level of outside noise .
112
-Check the settings whenever someone else
has dr iven the vehicle before you .
@ Tips
-The warn ing tones can also be adjusted di ­
rectly from the rear view camera image.
Simply press the Settings * cont ro l button .
- Changed settings are activated when park ­
ing assist is switched on again.
Error messages
Applies to vehicles: with parking system (rear, with rear view
camera)
If a warning tone is aud ible for about five sec­
onds when you turn on the ignition, there is a malfunction in the system. Have the problem cor ­
rected by your author ized Audi dealer .
Keep the sensors in the rea r bumper clean and
free from ice so that the aco ustic park assist sys ­
tem can function properly .

M N
ci u.. co ,...., \!) 1.1'1
N 1.1'1 ,....,
A WARNING ,~
A child in a rearward-facing child safety seat
installed on the front passenger seat will be
seriously injured and can be killed if the front
airbag inflates - even with an Advanced Airbag
System.
- The inflating airbag will hit the child safety
seat or infant carrier with great force and
will smash the child safety seat and child
against the backrest, center armrest, door
or roof.
- Always install rear-facing child safety seats
on the rear seat.
- If you must install a rearward facing child
safety seat on the front passenger seat be­
cause of exceptional circumstances and the
PASSENGER AIR BAG OFF light does not
come on and stay on, immediately install
the rear-facing child safety seat in a rear
seating position and have the airbag system
inspected by your authorized Audi dealer.
- Forward-facing child safety seats installed
on the front passenger's seat may interfere
with the deployment of the airbag and cause serious personal injury to the child .
A WARNING
If, in exceptional circumstances, you must in­
stall a forward-facing child restraint on the
front passenger's seat:
-Always make sure the forward-facing seat
has been designed and certified by its man­
ufacturer for use on a front seat with a pas­
senger front and side airbag.
- Never put the forward-facing child restraint
up against or very near the instrument pan­
el.
- Always move the passenger seat into its
rearmost position in the seat's fore and aft
adjustment range, as far away from the air­
bag as possible before installing the for­
ward-facing child restraint. The backrest must be adjusted to an upright position.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the time
whenever the ignition is switched on.
Airbag system
A WARNING
To reduce the risk of serious injury, make sure
that the
PASSENGER AIR BAG OFF light will
be displayed whenever a child restraint is in­
stalled on the front passenger seat and the ignition is switched on .
- If the
PASSENGER AIR BAG OFF light does
not stay on, perform the checks described
~ page 142, Monitoring the Advanced Air­
bag System.
- Take the child restraint off the front passen­
ger seat and install it properly at one of the
rear seat positions if the
PASSENGER AIR
BAG OFF
light does not stay on.
- Have the airbag system inspected by your
authorized Audi dealer immediately.
-Always carefully follow instructions from
child restraint manufacturers when instal­
ling child restraints.
A WARNING
If, in exceptional circumstances, you must in­
stall a forward or rearward-facing child re­
straint on the front passenger's seat:
- Improper installation of child restraints can
reduce their effectiveness or even prevent
them from providing any protection.
- An improperly installed child restraint can
interfere with the airbag as it deploys and
seriously injure or even kill the child -even
with an Advanced Airbag System.
-Always carefully follow the manufacturer's
instructions provided with the child safety
seat or carrier.
- Never place additional items on the seat
that can increase the total weight registered
by the weight-sensing mat and can cause in­
jury in a crash.
135

Airbag syste m
his or her back up against the backrest and the
backrest is not reclined ¢
page 114, Correct
passenger seating positions,
- the adu lt is not taking weight off the seat by
holding on to the passenger assist handle
above the front passenger door or supporting
their weight on the armrest,
- the safety belt is being properly worn and that
there is not a lot of slack in the safety belt web­
bing,
- accessory seat covers or cushions or other
things that may cause an incorrect reading or impression on the weight-sens ing mat under
the upholstery of the seat have been removed
from the front passenger seat,
- a safety be lt extender has not been left in the
safety belt latch for the front passenger seat .
In addition to the
P ASS ENGER AIR BA G OF F
light in the center of the instrument panel, the
message
PASSE NGER A IR BAG OFF or PASSEN­
GER AIR BAG ON
will briefly appear in the instru­
ment cluster display . Thi s is to inform the driver
of the current front passenger airbag status.
Important safety instructions on
monitoring the Advanced Airbag System
A WARNING
An airbag system that is not funct ion ing prop ­
erly cannot prov ide supplementa l protect ion
in a frontal crash.
- If the airbag indicator light ¢
page 19
comes when the vehicle is being used, have
the system inspected immediate ly by your
authorized Aud i dealer.
It is possible that
the a irbag will inflate when it is not s up­
posed to, or wi ll not inflate when it should.
A WARNING
If the front airbag in flates, a chi ld without a
child restraint, in a rearward-facing child safe­
ty seat or in a forward-facing child restraint
that has not been proper ly installed will be
ser iously injured and can be killed.
- Even though your veh icle is equipped with
an Advanced Airbag System, make certa in
that all ch ildren, especially 12 yea rs and
144
younger, a lways ride on the back seat prop­
erly restrained for their age and size.
- Always install forward or rear-facing child
safety seats on the rear seat -even with an
Advanced A irbag System.
- If you must install a rearward-facing child
safety seat on the front passenger seat be­
cause of exceptional circumstances and the
PASSENG ER AIR BAG OFF light does not
appear and stay on, immediately insta ll the
rea r-facing chi ld safety seat in a rear seating
position and have the airbag system inspect­
ed by your authori zed Audi dealer .
- A t ight tether or other s trap on a rea rward­
facing chi ld restraint attached to the front
p assenger sea t can put too much pressure
on the weight-sens ing mat in the seat and
reg ister more weight than is actually on the
seat. The heavier weight registered can make the system work as though an adult
were on the seat and deploy the Advanced Airbag when it must be suppressed caus ing
serious or even fatal injury to the child .
- If, in exceptiona l circumstances, you must
install a forward-facing child restraint on
the front passenger seat, always move the seat into i ts rearmost pos ition in the seat's
fore and aft ad justmen t range, as fa r away
from the airbag as possib le. The backrest
m ust be adjusted to an upr ight position.
Make sure that the
PASSENGER AIR BAG
OFF
li ght comes on and stays on all the time
whenever the ignit ion is switched on.
A WARNING
- If the PASS ENGER AIR BAG OF F light does
not go out when an adult is s itting on the
front passenger seat after tak ing the steps
described above, make sure the adult is
prope rly seated and restra ined at one of the
rea r seat ing pos itions.
- Have the airbag system inspected by your
author ized Audi dealer befo re transpo rting
anyone on the fro nt passenger seat.

Smart Technolog y
Clean off accumulated salt coating from
brake discs and pads w ith a few carefu l
brake applications .
- If you damage the front spoiler, or if you in­
stall a d ifferent spoiler, be sure the air flow
to the front brakes is not obstructed. Other­
wise the brake system could overheat reduc ­
ing the effectiveness of the entire brake sys­
tem.
- Failure of one brake c ircuit will impair the
braking capab ility result ing in an increased
stopp ing distance. Avoid driving the veh icle
and have it towed to the nearest autho rized
Audi dealer or qualified workshop.
- Never let the vehicle ro ll to a stop with the
engine shut off .
- If the brake booster is not work ing, the
brake pedal must be pressed considerably
harder to make up for the lack of booste r as­
sistance .
Electro-mechanical
power assist, dynamic
steering
The electro-mechanical power assist helps the
driver when steering.
Power steering adapts electronically based on
the vehicle speed .
Indicator lights and me ssages
• Stee ring defe cti ve! D o not dr ive vehicle!
If this indicator light tu rns on and stays on and
this message appears, the power steering may
have fai led .
Do
not contin ue driving. See yo ur authorized
Aud i dealer o r a qua lified repair facility for assis­
tance.
l ;r- ij Dynami c steering : S ys te m fault! You can
c on tinu e dr iving
If the indicator light turns on and the message
appears, the steer ing may be more difficult to
move or mo re sensitive than us ual. The steer ing
wheel may also be at an ang le when dr iv ing
straight.
174
Drive slowly to your authorized Audi dea ler or
qualified workshop to have the ma lf u nction cor­
rected.
' -r, ij Dynamic ste ering: i nitializing
If this driver message appears and the indicator
li ght is flashing on the i nstrume nt pane l, dynam­
i c steer ing* is being rein it ia lized . After sta rting
the engine, the steer ing whee l w ill move sligh tly.
Re-initialization might be necessary if the steer ­
ing whee l was moved hard to th e left and right
whi le the vehicle was not moving . The display
goe s out as soon as initiali zation is comp lete.
A WARNING
,-
H ave the dynamic steering* system malfunc-
tion repaired as soon as possible by an author ­
ized Audi dealer or qualified workshop - r isk
of accid ent!
@ Tips
- If the . or 'T fl indicator light only stays on
for a short time, you may cont inue driving.
- The dynamic steering* stab ility system s are
not availab le in the event of a system mal­
function .
- For add itional information on dynamic
steering*, refer to<=> page 103 .
Driving with your quattro
Applies to vehicles : wit h all -w hee l drive
With all-wheel drive , all four wheels are driven .
General information
With a ll-wheel drive, power is distrib uted to a ll
fo ur wheels . This happens automatica lly depend­
i ng on your driving style and the road conditions
at the t ime . See also <=> page 1 70 .
A center d ifferential distributes the driving power
variab ly to the front and rear ax le. It works to­
gether w ith select ive whee l torque control , which
activates when drivi ng throug h curves
¢ page 171 . W ith the sport diffe rential*, power
distribution to the rear wheels is var iable and can
be ad justed with d rive select ¢ page 103 .
1111-

Care and cleaning
- Never use gasoline, spot remove r, ben ­
zene, paint thinner or other solvents to
remove .
-Door wind ows
-Remove snow and ice on w indows and ex-
terior mirrors w ith a plastic scraper. To
avoid scratches, move the scraper only in
one direction and not back and fo rth .
- Never remove snow or ice from door w in­
dows and m irrors using warm or hot water
because this could cause cracks to fo rm.
- To avoid damage to the rear window de­
fogge r, do not apply any stic kers on the
heating w ires on the inside of the w indow.
- Decorat ive parts /trim
- Never use chrome care or cleaning prod-
ucts.
-Pa int
- To reduce the risk of scratches, the veh icle
must be free of d irt and dust before pol­
ishing or waxing .
- To prevent paint damage, do not polish or
wax the veh icle in direct sunlight .
-To reduce the risk of paint damage, do not
polish away rust spots.
- Remove cosmet ics and sunscreen immedi­
ately- these could damage the paint.
- Di spla ys
- To avoid scratches, do not use dry cleaning
methods on displays.
- Controls
- Make sure that no fluids enter the con-
tro ls, because this cou ld cause damage.
- Safet y belt s
- Do not remove the safety be lts to clean
them.
- Never clean safety belts or the ir compo­
nents chemically or with corrosive fluids
or so lvents and never allow sharp objects
to come into contact w ith the safety belts.
Th is could cause damage to the belt web­
bing.
- If there is damage to the webbing, the
connect ions, the retractors or the buckles,
have them replaced by an au thori zed deal­
er.
- Textile s/artificial leather /Alcantar a
188
- Never treat artificial leather/A lcantara
with leather care products, solvents, floor
polish, shoe polish, spot remove or similar
products.
- Have a specialist remove stubborn stains
to prevent damage.
- Never use steam cleaners, brushes, hard
sponges, etc . when cleaning.
- Do not turn on the seat heating* to dry the seat.
- Objects with sharp edges such as zippe rs,
rivets on clothing or be lts can cause dam­
age to the surface.
- Open hook and loop fasteners, for exam­ ple on clothing, can damage seat covers .
Make sure hook and loop fasteners are
closed.
- Natu ral leather
- Neve r treat leather w ith solvents, floor
polish, shoe polish, spot remover or simi­
lar p rodu cts.
- Objects w ith sharp edges such as zippe rs,
rivets on clothing or be lts can cause dam­
age to the surface.
- Never use steam cleaners, brushes, hard
sponges, etc. when cleaning .
- Do not turn on the seat heating* to dry the seat .
- To help prevent the leather from fad ing,
do not leave the vehicle in d irect sunlight
for long periods of time.
If leaving the ve­
h icl e parked for long periods of t ime, yo u
should cover the leathe r to protect it from
d irect sunlight.
(D Tips
- Insects are easier to remove from paint that
has been fresh ly waxed.
- Regular waxing can prevent rust spots from
forming.
Placing your vehicle out
of service
If you wo uld like to take yo ur vehicle out of serv­
ice for a longer time, contact your authorized
Audi dealer or qualified repair facility . They will
advise you of important measures ., such as ..,.