engine AUDI A5 CABRIOLET 2017 Service Manual

Intelligent Technology
These electronic control modules record data
dur ing normal vehicle operation that may be
needed by trained technicians for diagnostic and
repair purposes. The recording capability of these
modules is l imited to data (no sound is record­
ed). Only a small amount of data is actually re ­
corded over a very limited per iod of time, or stor­
ed when a system fau lt is detected by a control
mod ule. Some of the data stored may re late to
ve hicl e speed, dire ct ion, or brak ing, as well as re­
stra int system use and performance in the event
of a crash. Stored data can also only be read and
downloaded with special equipment that is di­ rectly connected to the veh icle.
@ Tips
Your vehicle may be equipped with Audi con­
nect. Your use of certain Audi connect fea­
tures requires wireless services that are pro­
vided by a third party wire less te lecommuni­
cations provider. For detai ls regarding how in­
formation obtained through Audi connect is collected, processed, t ransmitted, used, and
shared, please see your contract with the
w ireless te lecommunica tions p rovider and the
"About Aud i connec t" tab in your vehi cle's
M M I:
!MENUI b utton> Audi connect > About
Audi conne ct.
Braking
What affects broking efficiency?
New brake pads
During the fi rs t 250 miles (400 km), new b rake
pads do not possess the ir full braking effect, they
have to be "broken in" first ¢.& . You can com­
pensate for this s light ly reduced bra king power
by pushing harde r on the brake pedal. Avoid
heavy braking loads during the break-in period .
Operating conditions and driving habits
The brakes on today's automobiles a re st ill s ub­
ject to wea r, depending la rgely on ope rating con ­
ditions and driving habits¢.&, . On vehicles that
are either dr iven most ly in stop-and-go city traf ­
f ic or are driven hard, the brake pads should be
checked by your authorized Aud i dea ler more of­
ten than specified in the
War ranty & Mainte-
170
nance booklet . Failure to have your brake pads
inspected can result in reduced brake perform ­
ance.
On steep slopes, you should use the bra king ef ­
fect o f the engine. This way, you prevent unnec­
essary wear on the brake system. If you must use
your brakes, do not ho ld the brakes down contin ­
uously. Pump the brakes at intervals.
Ope rating nois e
Noises may occu r when braking depen ding on the
speed, braking force and outside conditions such
as temperature and h umidity.
Effect of water and road salt
In certain si tuations, for examp le after d riving
t hr ough water, in heavy rain, after over nigh t con­
densa tion or after washing your car, the brak ing
effect can be reduced by moisture or ice on the
brake rotors and brake pads . The brakes must be
dried f irst with a few careful brake app lications.
At higher speeds and w ith the windshield wipe rs
turned on, the brake pads press against the brake rotors for a short amount of time . This occurs at
regu lar intervals without the dr iver not icing and
provides for better brake response t ime under
wet cond itions .
The effectiveness of the brakes can be reduced
when the vehicle is driven on a salt-covered road
and the brakes are not used. Likewise, you clean
off accumulated salt coating from brake discs
and pads with a few caut ious applications of the
brake ¢.& .
Corrosion
There may be a tendency for dirt to build up on
the brake pads and corrosion to form on the discs
i f the car is not driven regularly or only for short
trips with little use of the brakes .
If the brakes are not used frequently, or if corro ­
s io n has formed on the discs, it is advisable to
clean off the pads and discs by braking firmly a
few times from a moderately high speed ¢ .& .

a:,
a:,
...... N r--. N ...... 0
0
LL 00
Fa ults in the brake system
If yo u should notice a sudden increase i n brake
pedal travel, then one of the two brake circuits
may have failed
¢ .&. .
Low brake fluid level
Malf unct ions can occur in the bra ke system if the
b rake fl uid leve l is too low. The brake fluid level
i s monitored e lectronica lly .
Bra ke booste r
The brake booster increases the pressure that
you generate with the brake pedal.
It works on ly
when the engine is run ning
.¢ .&.
Bra ke lining we ar status
Brake lining wear may be checked by visual in­
spection of the condition of the brake pads
through the open ings in the wheel. If necessary,
the wheel may be removed for this inspection
¢ page 228, Replacing wheels.
A WARNING
- New bra ke pads don't have the best stop­
ping power and must be "bro ken- in" dur ing
the init ia l 250 m iles (400 kilometers). Yo u
can compensate for th is by press ing the
brake pedal more firmly. This a lso applies
later when new pads are installed.
- Yo u should perfo rm braking maneuvers for
the p urpose of clean ing the brake system
only if road conditions permit. Other road
users must not be put at risk -you may
cause an accident!
- Before descending a steep grade, reduce
speed and shift t ransm iss ion into a lower
gear or lowe r driving range. Do not ride the
brakes or hold the pedal down too long or
too often. This could ca use the brakes to get
hot and diminish brak ing efficie ncy.
- Do not "r ide t he b rakes" by resting your foot
on the pe dal when yo u do not inten d to
bra ke. This may cause the bra kes to over­
heat, premat ure wear and increased stop ­
ping distance.
- Under certa in climatic and operating condi­
tio ns such as passing thro ugh water, driving
in heavy rain or after washing the vehicle,
Intellig ent Technology
the effectiveness o f the brakes can be re­
duced. In winter, ice can accum ulate on the
brake pads, lin ings, d iscs and drums . Care­
fu lly apply brakes for a test . Brakes will dry
and ice coat ings will be cleaned off after a
few ca refu l brake applications .
- Driving for an extended period of t ime on
salt-covered roads without usi ng your
b rakes can also affect braking eff iciency.
Clea n off acc umul ated salt coat ing from
b rake discs an d pa ds w ith a few careful
b rake appli cat ions .
- I f you d amage the front spoile r, or if you in­
s t all a different spoiler, be s ure the a ir flow
to the front brakes is not obstruc ted. Other­
wise the brake system could overheat reduc­ ing the effectiveness of t he ent ire bra ke sys­
tem.
- Fai lure of one brake circuit w ill impa ir the
braking capability resulting in an increased
stopping distance . Avoid driving the vehicle
and have it towed to the nearest authorized
Aud i dealer or qualified workshop.
- Never let the vehicle roll to a stop with the
engine shut off.
- If the brake booster is not working, the
brake pedal must be pressed cons iderab ly
ha rder to make up fo r the lack of booste r
assis tance .
Electro-mechanical
power assist, dynamic
steering
The electro-mechanical power assist helps the
driver when steering.
Power steer ing adapts electronically based on
the vehicle speed.
Indicator lights and messages
• Steering defe ctive! Do not drive vehicle!
If this indicato r light turns on and stays on and
t hi s message appears, the powe r steering may
have failed.
171

Intelligent Technology
Do not contin ue driving . See yo ur authori zed
Aud i dea ler or a qua lified repair facility for assis­
tance.
'I@ Dynamic steering : Sy stem fault! You can
cont inue d riv ing
If the indi cator lig ht t urns on and the message
appears, the steering m ay be more difficul t to
move or mo re sensit ive than usual. The steering
wheel may also be at an angle when dr iving
straight .
Dr ive s low ly to your author ized A udi dealer or
qu alified wor kshop to have the ma lfunction co r­
rected .
l;:r-ij Dynamic steering : initializing
If th is driver message appears and the ind icator
light is flas hing on the instrument panel, dynam­
ic stee ring* is be ing rein itia lized . Afte r start ing
the engine , the steer ing wheel will move s light ly.
Re-i nitializ ation m igh t b e necessa ry if the s teer­
i n g wheel was moved hard to the left and r igh t
while the veh icle was not moving. The disp lay
goes out as soon as initia lization is complete.
A WARNING
Have the dynamic steering* system malfunc­
tion repaired as soon as possible by an au­
thorized Audi dealer or qualified workshop -
r isk of accident!
(D Tips
- If the . or l;pij indicator light only stays on
fo r a short time, you may continue driving.
- The dynamic steering* stability systems are
not available in the event of a system mal­
funct ion.
- Fo r additional informat ion on dynamic
steering*, refer to
¢ page 101.
172
-
Driving with your
quattro
App lies to : vehicles wit h all -w hee l drive
With all-wheel drive , all four wheels ore driven .
General information
With a ll-wheel d rive, power is distrib uted to a ll
fo ur wheels. Th is happens automat ica lly depend­
i ng on your driving style and the road conditions
at the t ime . See also
¢ page 167.
A center d ifferential distributes the driving powe r
variably to the front and rear axle. It works to­
gether w ith select ive whee l torque contro l, wh ic h
activates when d rivi ng through curves
¢ page 167. With the spor t different ial*, power
dist ribution to the rear wheels is var iable and can
be adjusted wi th d rive select ¢
page 101 .
The all-whee l dr ive concept is designed for hig h
engine powe r. Your vehicle is except ionally pow­
e rfu l an d has excellent driving cha racteristics
bot h unde r no rmal d riving condi tions and o n
snow and i ce. A lways read and follow safety pre­
ca utions
~ ..&. .
Winter tires
When dr iving in the winter, yo ur vehicle with all­
whee l dr ive has a n advantage, even with regu la r
t ir es. In w inte r road cond it ions i t may be advisa­
ble to mo unt win ter tires (o r all-se ason tires) for
i mproved driveability an d braking: these ti res
must be mo unted on
all four whee ls. See also
¢ page 2 22, Winter tires.
Tire chains
Where tire ch ains are mandatory on certain
r oads, t his normally also applies to vehicles wi th
a ll- wheel drive ¢
page 222, Snow chains .
Replacing wheels/tires
Vehicles with all-w heel d rive mus t always have
ti res of the same size. Also avoid tires with diffe r­
en t tread dep ths. Fo r d eta ils see page
¢ page 21 4, New tires or wheels. liJJ>

a:,
a:,
...... N r--. N ...... 0
0
LL 00
Off-Road driving?
Your Aud i does not have enough g ro und clear­
ance to be used as an off -road vehicle. It is there ­
fore best to avoid roug h tracks and uneven ter­
rain as much as possible. A lso refer to
¢ page 175.
_&. WARNING
Always adjust you r driving to road and t raff ic
conditions. Do not let the extra safety afford­
ed by all-wheel drive tempt you into tak ing
extra risks.
-Although the all-whee l dr ive is very effec­
t ive, a lways remember that bra king capac ity
is limited by tire traction . Yo u should there­
fore not d rive a t exc ess ive speeds on icy or
slippery road su rfaces.
- On wet ro ad surfaces, be caref ul not to drive
too f ast be cause the fro nt wheels co uld be­
gin to slide on top of the w ater ( aquaplan ­
ing). If this sho uld o ccu r, you w ill have no
warning from a sud den increase in eng ine
speed as with a front-whee l dr ive vehicle .
Always drive at speeds wh ich are su ited to
the road cond it ions -risk of crash.
Energy management
Starting ability is optimized
Energy management controls the distribution of
electrical energy and thus optimizes the availa­
bility of electrical energy for s tarting the engine.
If a veh icle wit h a conventional energy system is
not driven for a long per iod of t ime, the battery is
d ischa rged by idling current consumers (e.g. im­
mo bilizer). In cert ain cir cums tan ces it c an result
i n there be ing insuff ic ient ene rgy available to
start the engine.
I ntell igen t energy management in your veh icle
h andles the distr ib ution of ele ct ric al ene rgy.
S tarting ab ility is mar ked ly imp roved an d the l ife
of the batte ry is extended.
B asically, e nergy management consis ts of
bat­
tery diagno sis, idling curr ent management
and
dynamic energy management .
Intelligent Technology
Battery diagnosis
Battery diagnos is con tinuously dete rmi nes the
state o f the bat tery . Sensors determine battery
vo ltage, battery c urrent and batte ry tempera­
tu re. This determines t he current state of charge
and the power of the battery.
Idling current management
Id ling cur rent management reduces ene rgy con­
s u mption whi le the vehicle is standing . With the
ignition switched off, it contro ls the energy sup­
ply to the vario us electrical components . Data
from battery d iagnosis is cons idered.
Depend ing on the ba ttery's s tate of charge, indi ­
vidual consumers are gradually turned off to pre­
vent excess ive discharge of t he battery and thus
mainta in starting capab ility.
Dynamic energy management
While t he vehi cle is being d riven, dynami c energy
management dis trib utes the energy generate d
according to the needs of the individual compo­
nents. It regulates consumption, so that more
electrical e nergy is not being used than is being
generated and ensures an opt imal state of
charge for the battery .
(i) Tips
-But even ene rgy management cannot neg­
ate the lim its of physics. Consider that the
powe r and life of a battery are lim ited.
- If starting ab ility is threatened, the indica ­
to r li ght (•) appears¢
page 14.
What you should know
The highest priority is given to maintaining start­
ing capability.
The battery is severe ly taxed in short-distance
driv ing, in city traffic and dur ing the cold time of
year. Abundant e lectrica l energy is required, but
o n ly a little is generated. It is also c ritical if the
engi ne is not running and electrical components
are tu rned on . In this instance energy is being
co nsumed bu t no ne is being ge nerated. .,,.
173

Intelligent Technology
It is in precisely these situations that yo u will no ­
tice energy management active ly regulating the
d istr ibut ion of energy.
Vehicle stands for an e xtended period
If you do not drive you r ve hicle over a period of
seve ral days or weeks, elec trical components are
g radually cut back or switched off . This reduces
energy cons umption and ma intains starting ca­
pability over a longer period. Some of the con­
ven ience funct ions may not operate, such as the
interior lights or the power seat adjustment. T he
conven ience functions will be available again
when yo u switch on t he ign it io n and start the en­
g ine .
With the engine turned off
If you listen to the radio, for example, with the
engine turned off o r use other MMI fu nctions,
the battery is being discharged .
If start ing capability is jeopardized due to energy
consumption, a message appears in the M MI dis­
p lay. The message indicates that the system will
be sw itched off automatically in a moment. If
you wish to cont inue using t he functions, you
have to start the engine.
With the engine running
Although electrical energy is generated when the
veh icle is being driven, t he battery can become
d ischa rged. This happens most ly when l ittle en ­
ergy is be ing generated and a g reat deal con­
sumed and t he battery's state of cha rge is not
opti mal.
To br ing the energy ba lance back into equ ilibri­
um, consume rs which req uire especially la rge
amo unts of energy a re tempora rily cut bac k or
sw itche d off. Hea ting systems i n par tic ul ar r e­
qu ire a gre at deal of energy. If you not ice, for ex ­
ample , that the heated seats* or the heated rear
window are not heating, they have been tempo ­
rari ly cu t back or switched off . These systems will
be ava ilab le aga in as soon as the energy balance
has been restored .
You will a lso notice that engine idle speed has
been inc reased slightly. This is normal and not a
cause for conce rn. By increasing eng ine idle
174
speed the a ddi tional energy required is genera t­
ed and the battery is charged.

a:,
a:,
...... N r--. N ...... 0
0
LL 00
Driving and the
environment
Breaking in
New engine
The engine needs to be run-in during the first
1,000 miles (1,500 km).
For the first 600 miles (1 ,000 kilometer s):
"' Do not use full throttle .
"' Do not drive at engine speeds that are more
than
2/3 of the max imum permitted RPM .
From 600 to 1,000 miles (1 ,000 to 1 ,500
kilometers):
"' Speeds can gradually be increased to the maxi­
mum pe rm issib le road or engine speed .
During and after break-in pe riod
"' Do not rev the engine up to high speeds when it
is cold. This applies whether the transmission is
in N (Neutral) or in gear .
After the break-in period
"'Do not exceed maximum engine speed under
any c ircumstances.
"'U pshift into the next higher gear
before reach­
ing the red area at the end of the tachometer
sca le
c=>page 8.
During the first few hours of driving, the eng ine's
internal friction is higher than later when all the
mov ing parts have been broken in . How well this
b reak-in process is done depends to a considera­
b le exte nt on the way the veh icle is d rive n during
t he first 1,000 miles (1,500 kilometers).
(D Note
Extremely high eng ine speeds a re au toma ti­
cally reduced. However, these rpm limits are
programme d for a n engine well run-in, not a
new engine.
@) For the sake of the environment
D o not dr ive with u nnecessari ly high eng in e
spee ds -ups hifting ea rly saves fuel, reduces
noise and pro tec ts the envi ronme nt .
Driving and the envir onment
New tires
If your vehicle is runn ing on new tires, d rive very
car efu lly fo r the firs t 35 0 miles (500 kilometers)
a ft er fit ting.
New tires tend to be slippe ry and must a lso
be "bro ken-in". Be sure to remembe r th is dur­
i ng the fi rst 350 m iles (500 kilometers).
Brake gent ly. Avoid following closely behind
other vehicles or other s ituations that m ight
r equire sudden, hard b raking.
Avoid damaging the
vehicle
When yo u are dr iv ing o n poor roa ds, or over
cur bs, stee p ramps, e tc., ma ke cert ain that low­
ly ing parts s uch a s spo ile rs a nd exh aust sy stem
parts do no t bottom o ut and get dama ged.
T his is espec ially true for ve hicles with low-s lung
c h ass is (sports c hass is) * and fully loaded
vehicles.
Driving through water on
roads
Note t he following to avoi d ve hicle damage w hen
driv ing through water, for examp le on flooded
roads:
- The water must not be any hig her t han the bot ­
tom of the vehicle body.
- Do not dr ive faste r than walk ing speed.
A WARNING
= -
Afte r driv ing th ro ugh water, m ud, slush, etc .,
the brakes may be slow to take effect beca use
of wet brake rotors and pa ds. Dry the brakes
f irst by braking carefully to restore the full
b raking effect.
(D Note
Ve hicle compone nts such as the engine,
transmission, suspension o r electrica l system
can be severely damaged by driving throug h
water.
Iii>
175

Driving and th e en vironm ent
(D Tips
- Check the depth of the water before driving
through it .
- Do not stop the veh icle, drive in reverse or
switch the engine
off when driving through
water.
- Keep in mind that oncoming vehicles may
create waves that raise the water level and
make it too deep for your veh icle to drive
through safely.
- Avoid driving through salt water because it
can cause corrosion.
Catalytic converter
It is very important that your emission control
system (catalytic converter) is functioning prop­ erly to ensure that your vehicle is running in an
environmentally sound manner .
~ Always use lead-free gasoline ¢ page 188,
Fuel supply .
~ Never run the tank down a ll the way to empty .
~ Never put too much motor oil in your engine
¢ page 19 7, 9::?l Adding engine oil .
~ Never try to push- or tow-start you r vehicle.
The cata lytic converter is an efficient "clean-up"
dev ice bu ilt into the exha ust system of the vehi­
cle. The cata lytic conve rter burns many of the
pollutants in the exhaust gas before they are re ­
leased into the atmosphere.
The exclusive use of unleaded fue l is critica lly im­
portant for the l ife of the catalytic conve rter and
p roper functioning of the engine.
A WARNING ,..____ -
- The temperature of the exhaust system is
high, both when driving and after stopping
the engine.
- Never touch the exha ust tail pipes once they
have become hot. This could result in burns.
- Do not park or ope rate t he vehicle in areas
where the hot exha ust system may come in
contact with dry grass, br ush, fue l spill or
other mater ial which can cause a fire.
- Do not apply additional undercoating or
rustproofing on or near the exhaust mani-
176
fold, exha ust pipes, cata lytic conve rter or
heat shields. D uring driving, the substance
used for undercoat ing could overheat and
cause a f ire.
Cl) Note
- Be aware that just one tank f illing wit h
leaded fu e l w ill already seriously degrade
the performance of the catalytic converter.
- Do not exceed the correct engine oil leve l
¢page 197.
-Do not drive until the fue l tank becomes
completely empty. The engine could mis­
fire. Unbu rned fue l cou ld also get into the
exhaust system and this could cause the
catalytic converter to overheat.
- Do not turn off the ign ition while the vehicle
is moving .
- Do not continue to operate your vehicle un­
der these conditions, as otherw ise fuel can
reac h the catalytic converter. T his could re­
sult in overheat ing of the converter, requir­
ing its replacement.
- T o ass ure eff icient operat ion of the Emis­
sion Contro l System:
- Have you r vehicle maintained properly and
i n accordance wit h the service recommen­
dations in your Warranty
& Ma intenance
booklet.
- Lack of proper ma intenance as well as im­
p roper use of the veh icle will impa ir the
function of the emission control system
and could lead to damage.
(® For the sake of the environment
Even when the Emiss ion Control System is op­
erating properly, t he exhaust gas can have a
sulfur-like exhaust gas smell under some op­
erating states. Th is depends on the sulfur
content of the fuel being used. Us ing a d iffer­
ent brand of fuel may help, or fi lli ng the tank
wi th lead-free super g rade gasoline.
Shutting down vehicle
If you wo uld like yo ur vehicle to remain inopera­
tive for a longer pe riod of time, con tact an Audi
o r other spec ia liz ed dealer. They can adv ise you ..,.

a:,
a:,
...... N r--. N ...... 0
0
LL 00
on necessary precautions e.g. co rrosion preven­
tion, maintenance and storage . Pay attention to
addit ional information concerning the battery .
Refer to
¢ page 203 .
Economical and environ­
mentally-friendly driving
General
Your personal style of driving will determine the
economy of your vehicle, as well as exhaust and
noise levels.
F ue l economy, environmenta l impact, and we ar
on your engine, brakes and tires la rgely depend
on three factors :
- you r persona l dr iving sty le
- operating conditions
- technical lim itations
If you anticipate what you need to do next and
drive economically, you can eas ily cut your fue l
consumption by
10-15 percen t. This section will
g ive you some tips on how you can help the envi ­
ronment and yo ur pocketbook .
(!) Tips
The consumpt ion estimates as published by
ENVIRONMENTAL PROTECTION AGENCY (EPA) and Transport Canada may not cor re­
spond to your actual consumption on the
road, which will va ry depending upon vehicle
load and speed, road and wea ther condi tions,
t rip length, etc.
Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are acceler­
ating.
" Avoid unnecessary accelerating a nd braking .
Veh icles use the most fuel when they are acceler ­
ating . If you anticipate what is going to happen
next , you will need to brake less and, thus, accel­
e rate less . let the vehicle coast wheneve r possi ­
b le -fo r example when yo u see that the next traf­
fic light is red.
Driving and the envir onment
Avoid full throttle
Driving at moderate speeds saves fuel and im­
proves your mileage .
"Try and keep well below your car 's maximum
speed.
Acce lerating gently reduces fuel consumption,
engine wear, and does not disturb the environ­
ment.
Fuel consumption, exhaust emissions and engine
noise increase disproport ionately at high speeds.
If you drive at approximately three quarters of
top speed, fuel consumption will be reduced by
one half. Never drive faster than the posted
speed limit and weather cond itions permit .
Reducing unnecessary idling
Even when your car is jus t idling it burns up fuel.
" Shut the eng ine off when you are not driving
the vehicle.
" Do not warm up the vehicle by lett ing the en-
gine run at idle.
It makes sense to shut off the engine in traffic
jams, when waiting for trains to pass at railroad cross ings, or at traff ic lights that have long waits
on red . Turning the engine off for just
30 -40 sec ­
onds saves more f uel than is burned starting the
. . engine again.
It takes a long time for the eng ine to warm up
fully when it is running at idle . However, wear
and noxious emissions are especially h igh when
the engine is warming up . So yo u should dr ive
away as soon as you start the eng ine and avoid
runn ing at high rpms w hile the engine is st ill
warming up .
(D Note
Do not leave eng ine idling unattended after
s tart ing. If wa rning lights sho uld come on to
i ndicate improper operation, they would go
unheeded . Extended idling also prod uces
heat, which could resu lt in overheating or
other damage to the vehicle or other proper­
ty .
177

Driving and th e en vironm ent
Regular maintenance
A badly tuned engine unnecessarily wastes a lot
of fuel.
.,. Have your vehicle serviced at regular intervals.
By having your vehicle regu larly serviced by an
author ized Audi dealer he lps to ensure that it
runs properly and econom ically . The condition of
your veh icle not only affects its safety and ability
to hold its value, it also affects
fu el consump­
tion .
C he ck your oil e ach t ime you fill you r ta nk .
The amount of oil used is re lated to engine load
and speed.
It is normal for the oil consumpt ion of a new en­
g ine to reach its lowest val ue afte r a certa in mile­
age has been driven .
You must d rive you r vehicle about 3 ,000 miles
(5,000 k ilome ters) before you can p roperly as ­
sess o il cons umption .
This a lso applies to fuel consumption and engine
outpu t.
(D Note
- Have your vehicle maintained properly and
in accordance with the service recommenda­
tions in you r Warranty
& Maintenance book ­
l et . La ck of p roper main tenance as well as
i mproper use of the vehicle will impa ir the
f u nct ion of the emission control system and
could lead to damage.
- Do not al ter or remove any component of
the Emission Control System unless ap­ proved by the manufacturer.
- Do not a lter or remove any device, such as
heat shie lds, switches, ignition wires,
valves, which are designed to protect your
vehicle's Emission Control System and other i mportant vehicle components.
178 ·
Fewer short trips
Fuel consumption will always be relatively high
on short trips .
.,. Try to avoid driving short distances with a cold
eng ine .
T he eng ine and catalytic converter have to reac h
their opt imal
operating temper atu re to reduce
fuel consumpt ion and noxious emiss ions effec­
tively .
Just after start ing, a cold engine in a mid-size car
on ly achieves a fuel economy of 6-8 miles per
gallon (30-40 l/100 km) . After about a half a
mile, fuel economy climbs to 12 mpg (20 l/100
km) . After about
2 .5 m iles (4 km), the engine is
at its proper operating temperatu re and fuel
economy has reached a no rma l level. So you can
see that you should avoid sho rt tr ips wheneve r
possible .
The
out sid e temperatur e is also cr it ica l in th is re­
gard. Your car cons umes more fue l in the winter
than in the summer.

Trailer towing Driving with a trailer
General information
Your Audi was designed primarily for passenger
transportation .
If you plan to tow a trailer, please remember that
the additional load will affect durability, econo­
my and performance.
Trailer towing not only places more stress on the
vehicle, it also calls for more concentration from
the driver.
For this reason, always follow the operating and
driving instructions provided and use common
sense.
Technical requirements
Trailer hitch
Use a weight-carrying hitch conforming to the
gross trailer weight. The hitch must be suitable
for your vehicle and trailer and must be mounted
securely on the vehicle's chassis at a technically
sound
location . Use only a trailer hitch with a re­
movable ball mount . Always check with the trail­
er hitch manufacturer to make sure that you are
using the correct hitch.
Do not use a bumper hitch.
The hitch must be installed in such a way that it
does not interfere with the impact -absorbing
bumper system . No modifications should be
made to the vehicle exhaust and brake systems .
From time to time, check that all hitch mounting
bo lts remain securely fastened.
When you are not towing a trailer,
remove the
tra iler hitch ball mount . This prevents the hitch
from causing damage shou ld your vehicle be
struck from beh ind ¢
,&. .
Trailer brakes
If your trailer is equipped with a braking system,
gi check to be sure that it conforms to all regula-......
~ tions . N ...... 0
0
LL 00
Trailer towing
The trailer hydraulic brake system must not be
directly connected to the vehicle's hydraulic
brake system ¢.&. .
Safety chains
Always use safety chains between your vehicle
and the trailer.
Trailer lights
T ra iler lights must meet all regulations . Be sure
to check w ith your author ized Audi dealer for cor­
rect wiring, switches, and relays.
Mirrors
If you are unable to see the traffic behind you us­
ing the regular outside mirrors, then you
must in­
stall extended mirrors. It is important that you
always have clear vision to the rear.
,8. WARNING
-If a tra iler has electr ical brakes please note
that these bra kes are not activated by the
factory-fitted control unit -risk of accident!
- After removing the trailer hitch, do not
store it in your vehicle. In case of sudden
braking, the hitch could fly forward and in­
jure you or your passengers.
Operating instructions
Maximum trailer weight
A trailer for your vehicle is limited to a typical
class 1 or class 2 trailer.
Trailer load distribution
Be sure the load in the trailer is held sec ure ly in
place to prevent it from shifting forward, back­
ward or sideways.
Never allow a passenger to ride in a trailer¢.&.
in Driving instructions on page 180.
Engine cooling system
Towing a trailer makes the engine work harder . It
is important that the cooling system's perform ­
ance is up to the additional load . Make sure that
the cool ing system has enough fluid. .,..
179