radio AUDI A5 COUPE 2010 Owner's Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 2010, Model line: A5 COUPE, Model: AUDI A5 COUPE 2010Pages: 360, PDF Size: 84.39 MB
Page 290 of 360

-~_T_ ir_e_ s_ a_ n_d _ w_ h_ e_e _l_s _________________________________________________ _
& WARNING (continued)
crashes and serious personal injuries . Have worn or damaged tires
replaced immediately.
• Tires age even if they are not being used and can fail suddenly,
especially at high speeds. Tires that are more than 6 years old can
only be used in an emergency and then with special care and at
low speed.
Glossary of tire and loading terminology
Accessory weight
means the combined weight (in excess of those standard items
which may be replaced) of automatic transmission, power steering,
power brakes, power windows, power seats, radio, and heater, to
the extent that these items are available as factory-installed equip
ment (whether installed or not).
Aspect ratio means the ratio of the height to the width of the tire in percent.
Numb ers of 55 or lower indicate a low sidewall for improved
steering response and better overall handling on dry pavement.
Bead
means the part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is shaped to fit the rim.
Bead separation means a breakdown of the bond between components in the bead.
Cord
means the strands forming the plies in the tire.
& WARNING (continued)
• Never mount used tires on your vehicle if you are not sure of
their "previous history." Old used tires may have been damaged
even though the damage cannot be seen that can lead to sudden
tire failure and loss of vehicle control.
• If you notice unusual vibration or if the vehicle pulls to one side
when driving, always stop as soon as it is safe to do so and check
the wheels and tires for damage . •
Cold tire inflation pressure
means the tire pressure recommended by the vehicle manufacturer
for a tire of a designated size that has not been driven for more than
a couple of miles (kilometers) at low speeds in the three hour period
before the tire pressure is measured or adjusted.
Curb weight means the weight of a motor vehicle with standard equipment
including the maximum capacity of fuel, oil, and coolant, air condi
tioning and additional weight of optional equipment.
Extra load tire
means a tire design to operate at higher loads and at higher infla
tion pressures than the corresponding standard tire. Extra load tires
may be identified as "XL",
"xi", "EXTRA LOAD", or "RF" on the side
wall.
Gross Axle Weight Rating ("GAWR")
means the load-carrying capacity of a single axle system, measured
at the tire -ground interfaces.
Gross Vehicle Weight Rating ("GVWR"l
means the maximum total loaded weight of the vehicle.
Page 310 of 360

-~_T_ ir_e_ s_ a_ n_d _ w_ h_ e_e _l_s _________________________________________________ _
Fig. 235 Display:
System malfunction
Usin g the ABS senso rs, the tir e pressure monitor ing system
c o mp ares the tire t read ci rc um fere nc e a nd vibr atio n c harac te ristic s
o f the i ndividual ti res . If t he press ure decr eas es in one or mor e tires,
th is is ind ica te d in the i nstru me nt clust er w ith a wa rning symbol
fl
and a messa ge=> page 3 0 7, fig . 234. The driv er m essage i n th e
dis play goes out after
5 seconds. The driver message can be
d isp lay ed aga in by p ress ing the
!SE T] button. I f only one tir e is
affected, the disp lay wil l indicate its position .
Th e ti re pr essur e mo nitori ng system mu st b e rese t via ra dio or MM I*
each t ime the pressur es are adjusted (e.g. when sw itchi ng b etw een
p a rt ial an d fu ll lo ad pr essu re) or after changi ng or re pl acin g a tire
on your vehic le=>
pa ge 30 9. You can find t he recommended t ire
pressures for your vehic le on the label on driver's side B -pil lar
=>
p ag e 291 .
Tire tread circ umference and vibration characteristics can change
a nd ca use a tire pre ssur e warni ng i f:
• th e t ire pr essure in o ne or mor e tires is too low,
• t he tir e h as structur al d am age,
• the tire pressure was changed, whee ls rotated or replaced but
th e TP MS was not re set =>
page 30 9.
Warning symbols
\.) Loss of pressur e in at le ast one tire => & . C heck the t ire or tire s
and re place or repa ir if necessar y. T he indicato r light
1 in the instrument cluster also
ill uminates=>
page 1 2. C heck/correct th e
p res su res of a ll four tir es and re set TPMS via radio or MMI *.
~ (T ir e Pressure Monito rin g S ystem) Tire pressure! System
malfunction.
I f v a p pears a fter switch ing the i gnition on or w hile drivin g
=> fig. 235 and the indicator light,. in the instrument cluster blinks
f or approx im ately one min ute and then sta y s on , the re is a syste m
malfunct ion . S ee your authorize d Audi dealer as soon as possib le .
& WARNING
• If the tire pressure indicator appears in the instrument cluster
display, one or more of your tires is significantly under -inflated .
Reduce your speed immediately and avoid any hard steering or
braking maneuvers. Stop as soon as possible and check the tires
and their pressures . Inflate the tire pressure to the proper pressure
as indicated on the vehicle's tire pressure label
=> page 291.
Driving on a significantly under -inflated tire causes the tire to over
heat and can lead to tire failure . Under-inflation also is likely to
impair the vehicle's handling and stopping ability .
• The driver is responsible for maintaining the correct tire pres
sures . You must check the tire pressures regularly .
• Under certain conditions (such as a sporty driving style , winter
conditions or unpaved roads ), the pressure monitor indicator may
be delayed.
• Ask your authorized Audi dealer if run -flat tires may be used on
your vehicle. Your vehicle registration becomes invalid if you use
these tires when not permitted . Damage to your vehi cle or acci
dents could also result.
[ i ] Tips
• Th e tir e pr es sur e m oni tori ng syst em stops wor king whe n there
i s an ESP/A BS malfunction.
• U sing s now ch ai ns m ay r esu lt in a s ystem malf u ncti on . .,_
Page 311 of 360

__________________________________________________ T_ ir_e _ s_ a_ n _ d_ w_ h_ e_ e_ls _ ____. 1'111
• To ensure a proper TPMS function use AUDI Original Tires which
are marked with "AO" or "RO" on the tire sidewall. =:>
page 299.
• The tire pressure monitoring system on your Audi was calibrated
using tires with the "AO" or "RO" identification. We recommend
using these tires.•
Applies 10 vehicles: with tire pressure monitor ing sys tem
Reset tire pressure monitoring system
If the tire pressure is adjusted, wheels are rotated or
changed, the TPMS must be reset via radio or MM/ *.
-Turn on the ignition.
Fig . 236 Car: Tire pres
sure monitoring
system
Select: the I CAR I function key> Tire pressure monitoring
> Store now.
[ i] Tips
Before resetting the TPMS, the current pressures of all four tires
must correspond to the specified values. Adjust the tire pressure
and reset the pressure in the tire pressure monitoring system
according to the load you are carrying =:>
page 291 . •
Vehic le care I I irechnical data
Page 324 of 360

-Fuses and bulbs Pffl.,___ ______________ _
No. Consum er Ampere
4 Dynamic steering
35
5 Climatized cupholder 10
6 Vehicle electrical system contro l module 1 35
7 Vehicle electrical system control module
1
20
8 Vehicle electrical system con tro l module 1 30
9 Panorama sunroof
20
10 Vehicle e lectrical system contro l module 1
30
1 1 Panorama sunroof shade 20
12 Convenience electronics 5
Fuse Location, Instrument Panel right
Fig . 2 49 Fuse panel
l ay ou t
Some of the equipment items lis ted are optional or only available on
certain model configurations.
Note th at th e fo llo wi ng t able i s ac cur ate at the time of going to
pr ess an d is s ubje ct to chan ge. In th e eve nt of d iscrep ancies, the
label o n the in side of th e cover alw ays take s pr ece de nce.
•
T he power seats are protected by cir cuit break ers, which automati
cally reset after a few seconds after the overload has been reme
died.
No . Co nsumer
Fu se p anel (blac k)
1 Not used
2 Not used
3 Not used
4 Not used
5 Steering column switch module
6 E
lectronic Stabilization Program
7 Terminal 15 diagnostic connector
8 Gateway
9 Not used
10 Not used
11 Not used
12 Not used
Fu se panel (brown )
1 CD-/DVD player
2 Audi drive select switch mo dule
3 MM I/Radio
4 Instrument cluster
5 Gateway
6 I
gn ition lock
7 Rotary light switch
8 Climate control system blower
9 Steering column lock
Amper e
5
5
5
5
5
5
5/20
5
5
5
5
40
5
Page 326 of 360

11111.___F_ u_ s _ e_s _ a_n _ d_ b_ u_lb _ s _______________________________________________ _
No. Consum er
7 Parking system
8 Rear wiper (Avant)
9 Electromechanical parking brake switch
10 Audi side assist
1 1 Rear seat heating
12 Terminal 15 control modu les
Fu se panel E (bla ck)
1 N ot used
2 Not used
3 DSP amp lifier, radio
4 MMI
5 Radio/navigation/cel l phone prep
6
Rearview camera
7 Not used
8 Not used
9 N ot used
10 Not us ed
1 1 Not used
12 Not used
Ampere
7,5
15 5
5
5
5
30/20
7,5
7,5
5
•
Bulbs
Replacing bulbs
For your s afety, we recommend th at you have your autho
ri zed Audi dealer replace any bulbs for you.
It is becoming increasingly more and more difficult to replace
vehic le light bulbs since in many cases, o ther parts of the car must
first be removed before you are able to get to the bu lb . This applies
especia lly to the light bu lbs in the front of your car which you can
only reach through the engine compartment .
Sheet metal and bulb holders can have sharp edges that can cause
serious cuts, parts must be correctly taken apart and then properly
put back together to help prevent breakage of parts and long term
damage from water that can enter housings that have not been
properly resealed.
Fo r your safety, we recommend that you have your authorized Audi
dea ler replace any bulbs for you, s ince your dealer has the proper
tools, the correct bulbs and the expertise.
Ga s di scharg e lamps (X enon ligh ts)*:
Due to the high electrical voltage, have the bulbs replaced by a qual
ified technician . Headlights with Xenon light are identified by the
high voltage sticker .
& WARNING
Changi ng Xeno n lamp s w ithout th e necess ary e quipm ent can
c a use se riou s pers on al injury .
• Bulb s are p ress urize d and can e xpl ode when being ch ange d.
Po tentia l ri sk of injury!
• On ve hic les equ ippe d with g as disc ha rg e bulb s (Xenon li ght )*
li fe -thre atening injuri es can re sult from impro per h andling of th e
hi gh-v olt age portion s of su ch lam ps! .,_
Page 329 of 360

________________________________________________ E_ m ___ e_r.::g ~e ___ n_c ~y:.- s;_ i_t _u :...:a:..:. t.:.: i...:o :...:n...:..:. s _ __,J_
& WARNING !continued)
• Before you check anything in the engine compartment, always
read and heed all WARNINGS~ page 263, "Engine compartment".
0 Note
• Applying a higher voltage booster battery will cause expensive
damage to sensitive electronic components, such as control units,
relays, radio, etc .
• There must be no electrical contact between the vehicles as
otherwise current could already start to flow as soon as the positive
(+) terminals are connected.
[ i) Tips
• The discharged battery must be properly connected to the
vehicle's electrical system. When jump starting or charging the
battery , never connect the negative ground cable to the battery
negative post because the battery manager system must be able to
detect the battery's state of charge. Always connect the negative
ground cable to the negative ground post of the battery manager
control unit .•
Use of jumper cables
Make sure to connect the jumper cable clamps in exactly
the order described below!
Fig. 251 Engine
compartment : Connec·
tors for jumper cables
and charger
Fig. 252 Jump starting
with the battery of
another vehicle: @
discharged vehicle
battery,
© booster
battery
The procedure described below for connecting jumper
cables is intended to provide a jump start for your vehicle.
Vehicle with discharged battery:
Turn off lights and accessories, move lever of automatic
transmission to
N (Neutral) or P (Park) and set parking
brake.
~
Vehicle care Do-it-yourself service irechnical data
Page 344 of 360

___ C_ o_n_ s_ u_m _ e_ r_ ln_ f_ o _r _m _ a_ t_ i_o _n ______________________________________________ _
& WARNING (con tinued)
men t zo nes. Doin g s o w ill in cre ase the r isk of injury if airb ags are
t rigg ered in an accid en t!
• Before you che ck anything i n the e ngine co m partment , always
re ad and heed all WARN IN GS
~ page 263.
0 Note
• If items other than genuine Audi spare par ts, add-on equipment
and accessory items are used or if repair work is not performed
according to specified methods, this can resu lt in severe damage to
your vehicle 's engine and body (such as corrosion) and adverse ly
affect your vehicle's warranty .
• If emergency repairs must be performed elsewhere, have the
vehic le examined by an authorized Audi dealer as soon as possible.
• The manufacturer cannot be held liable for damage which occurs
due to fai lure to comply w ith these stipu lations. •
Technical Modifications
Our guidelines must be c omplied with when technical
modifi cations are made.
Always consult an authorized Audi dealer before starting work on
any modifications.
This will he lp ensure that vehicle function, performance and safety
are not impaired ~& .
Attempting to work on e lectronic components and the software
used with them can cause malfunctions. Because of the way e lec
tronic components are interconnected with each other, such
malfunctions can also have an adverse affect on other systems that
are not directly involved . This means that you risk both a substantial
reduction in the operational safety of your vehicle and an increased
wear of vehicle parts~& . Authori
zed Audi dealers will perform this work in a professiona l and
competent manner o r, in special cases, refer you to a professiona l
company that specializes in such modifications .
& WARNING
Improper r epair s and m odifica tion s can ch ange th e way veh ic le
syst ems w ork and cau se seri ous per sonal inju ry .
0 Note
If emergency repairs must be performed elsewhere, have the
vehicle examined by an authorized Audi dea ler as soon as
possible. •
Declaration of Compliance,
Telecommunications and Electronic
Systems
Radio Frequency Devices and Radiocommunication
Equipment User Manual Notice.
The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment.
D ev ices
The fol lowing devices each comply with FCC Part 15.19, FCC Part
15.21 and RSS -Gen Issue 1:
• Adaptive cruise control*
• Convenience key*
• Audi side assist*
• Cell phone package*
• Electronic immobilizer
• Homelink ® universal remote control *