wipers AUDI A5 COUPE 2010 Owners Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2010, Model line: A5 COUPE, Model: AUDI A5 COUPE 2010Pages: 360, PDF Size: 84.39 MB
Page 36 of 360
Driver information display
more difficult or sensitive than usual. The steering wheel can also
be at an angle when driving straight.
Dynamic steering: initialization
If this driver message appears and the indicator light is flashing
on the instrument panel, dynamic steering is being reinitialized.
Once you start the engine after this is finished, the steering wheel
wi ll be easy to move. Re-initialization might be necessary if the
steering whee l was moved hard to the left and right while the
vehicle was not moving. The display goes out as soon as initializa
tion is complete .
& WARNING
Have the dynamic steering system malfunction repaired as soon
as possible by an authorized Audi dealer or any qualified work
shop -risk of accident!
[ i ] Tips
The dynamic steering stability systems are not available in the event
of a system malfunction. •
Applies to vehi cles: wit h conven ienc e key
Key not in vehicle
Key not in vehicle
This reminder appears along with the symbol if the master key is
removed from the vehicle with the engine running. It is intended to
remind you (e .g. when changing drivers) not to continue the journey
without the master key.
If the master key is no longer in the vehicle, you cannot switch off
the ignition after stopping the engine and you also cannot start the
engine again . You also cannot lock the vehicle from the outside .•
Ap plies to vehi cles : w it h li ght/ ra in sensor
Light /rain sensor defective C../1
...i-Automatic headlights /automatic wipers defective
If the symbo l il luminates, the light sensor has failed . For safety
reasons the low beams are turned on permanently with the switch
in
AUTO . However, you can continue to turn the lights on and off
using the light switch. In the case of a defect in the rain sensor, the
windshie ld wiper lever functions are still available. Have the
light/rain sensor checked as soon as possible by an authorized Audi
dea ler. •
Worn brake pads
Brake pads!
If the warning light illuminates, immediately contact your autho
rized Audi dealer or qualified workshop to have all brake pads
inspected . On USA models the warning light 't comes on together
with the warning light
BRAKE . Both sets of brake pads on an axle must
a lways be replaced at the same time .
& WARNING
Driving with bad brakes can cause a collision and serious personal
injury.
• If the warning light and the warning lig ht
BRAKE1
l with the
message Brake pads! comes on in the instrument cluster display ,
immediately contact your authorized Audi dealer or qualified
workshop to have all brake pads checked or replaced if
necessary .•
1 1 BRAK£ : USA models only
Page 39 of 360
Windshield wipers faulty .::>
-Windscreen wiper defective !
When this symbol ., illuminates, it means that the electronics for
the windshield wipers are defective . Please go to an authorized Audi
dealer or qualified workshop to have the windshield wiper system
repaired. •
Controls and equip
ment
Driver information display
I • •
Page 63 of 360
[ i J Tips
• Pressing the button l~•~ l seve ral times consecutively can tr igger
the over load protection . The sun shade can only be
extended/re tracted again af ter a brief waiting period.
• The rea r window sun shade only functions when the vehicle inte
rio r is wa rmer than 23°F (-5°Cl. •
Wiper and washer system
Switching on the windshield wipers
Fig. 6 3 Win dshield
w iper l ever
M ove the windshield w iper lever to the c orresp onding position :
@-Windshie ld w iper off
G) -Interva l mode. To extend/shorten the wiper inte rvals, move the
sw itc h @ to the lef t/right. In vehic les wi th a rain sensor*, the w ind
shield wipers are activated automatically starting at a speed of
2 mph (4 km/h). The higher the sensitivity of t he rain senso r* is set
(switch @to the right), the earlier the windshield wipers react to
moisture on the windshie ld.
@ -Slow wipi ng
© -Fast wiping
Con tro ls and eq uip
ment
Clear vision
© -Single wipe
© -C lean the windshie ld. To eliminate wate r droplets, the wind
shie ld wiper performs one afterwipe operation after several
seconds whi le d riving. You can switch this function off by moving
the lever to pos ition © within 10 seconds o f the afterwipe opera
tion. The afterwipe function is reactivated the next time the ignition
is sw itched on.
Cleaning the headlights *. The headlight washer system * only func
tions when the light is switched on . The headlights are automati
ca lly c leaned the first time and every fifth time the lever is moved to
pos ition
® · They are also cleaned every time you hold the lever in
pos ition © for longer than 2 seconds.
& WARNING
• The rain sen sor is only intended to a ssi st the driver . The driver
is still responsible for manually swit ching the wiper s on according
to the visibility conditions .
• The windshield may not be treated with water -repelling wind
s hield coating agents . Unfavorab le conditions , such as wetnes s,
darkness , low sun , can result in increased glare . Wiper bl ade
c hatter is also po ssible .
• Properly functioning windshield w iper blades are required for a
clear view and safe driving
~ page 63 , "Installing new wiper
blades ".
0 Note
• I n the case of frost, check whether the windshie ld wiper blades
are frozen to the windshield . Switching on the windshield wipers
ca n damage the wiper b lades !
• P rior to using a car wash, the windshield wiper system must be
switched off (lever in posi tion 0). This prevents un intentiona l
switching on and damage to the windshield wiper system. .,.
Vehicle care I I irechnical data
Page 64 of 360
Clear vision
[ i J Tips
• The windshield wipers are switched off when the ignition is
turned off. Activate the windshield wipers after the ignition is switched back on by moving the windshield wiper lever to any posi
tion .
• Worn or dirty windshield wiper blades result in streaking. This
can affect the rain sensor * function. Check your windshield wiper
blades regularly.
• The rain sensor * is part of the interval wiping system. Turning off
the ignition will also deactivate the rain sensor*. To reactivate the sensor, switch off the interval wiping function, then switch it back
on again.
• The washer fluid nozzles of the windshield washer system are
heated at low temperatures when the ignition is on.
• When stopping temporarily, e.g. at a traffic light, the set speed of
the windshield wipers is automatically reduced by one speed .•
Service position
The windshield wiper blades are replaced in the service
position .
Fig. 64 MMI Display:
Windshield wipers Fig. 65
Servic e posi
tion
The service position is set in the radio or MMI*.
If the wiper blades are not frozen to the windshield, bring
the windsh ield wiper lever to the basic position@
~ page 61, fig. 63.
- Select: Function button
[CARI> Windshield wipers>
Service position ~
fig. 64.
• On -changing the windshield wiper blades can only be done if
you bring the wiper arms to the service position
=> fig. 65. You will
also avoid paint damage to the hood when working on the wipers in
this position .
• Off -the windshield wipers are moved to their initial position
again.
0 Note
Never maneuver your vehicle with the front windshield wiper arms
raised since they will automatically be moved back to their basic
position above a speed of 3 mph (6 km/h) and can scratch the hood.
[ i J Tips
• You can also use the service position, for example, if you want to
protect the windshield from icing by using a cover . _,,
Page 65 of 360
• The service position automatical ly switches to Off when you
opera te the windshie ld w iper lever, or speed exceeds 3 mph (6
km/h). •
Installing nevv wiper blades
Wiper bl ades in good c on dition help keep the win dshield
clear.
Removing th e wiper blade
Fig. 6 6 Rem oving t he
w ip er bl ad e
- Bring the windshield wipers to the service posi tion
=> page 62.
- Lift the windsh ield wiper arm up from the w indshie ld.
- Press the locking knob
G) => fig. 66 o n the wiper blade.
H old t he wiper b lade firm ly.
- Remove the wip er b lade in the d irect ion o f th e arrow.
Attaching the wip er blad e
-Install the new wiper blade i n the retainer on the wiper
arm
0 u ntil you hear it click into place on the wiper a rm.
- Place the w iper a rm back on t he windsh ield.
Controls and equip
ment
Cl ea r vision
& WARNING
• Cle an your w ip er blade s re gularly w ith a w ind shield was her
s olut ion to prevent streak ing . If the w iper bl ade s are very d irt y, for
ex am ple wi th in sects, c arefull y cl ean th e wiper blad es with a
sponge or a soft brush .
• For yo ur safety , you should repla ce the wiper b lade s o nce or
twice a year. See your authori zed Audi dealer for replacem ent
bl ade s.
0 Note
• The windshield wiper blades must only be replaced when in the
service position ~
page 62! Otherwise, you risk damaging the paint
on the hood or the windshie ld w iper motor.
• To prevent damage to the wiper system, always loosen blades
which are frozen to the windshield before operating wipers .
• To prevent damage to wiper blades, do not use gasoline, kero
sene , paint thinner, or o ther so lven ts on or near the wiper blades.
• To prevent damage to the wiper arms or other components, do
not attempt to move the wipers by hand .
[ i ] Tip s
Commercial hot waxes applied by automatic car washes affect the
how easily the g lass surface can be c leaned .•
Mirrors
Manual glare-dimming
Standard s etting
- Move the sma ll leve r (located on the bottom edge of t he
m irror) to the front. _.
I • •
Page 239 of 360
•
appears in the display as well. The ASR can be deactivated at any
speed.
The ASR should normally be activated all the time . Only in certain
exceptional situations when some s lip is desirable does it make
sense to deactivate the ASR. Examples:
• when driving with tire chains
• when driving in deep snow or on loose ground and
• when rocking the vehicle loose after it has become stuck.
When the abnormal situation is over, you should activate the ASR
again.
& WARNING
The increased safety afforded by ASR does not mean that you can
take safety risks. Always adapt your driving style to the road
conditions and traffic situation.
[ i ] Tips
To ensure that the ASR works properly, al l four wheels must be fitted
with identical tires. Any differences in rol ling radius of the tires can
cause the system to reduce engine power when this is not desired.
See also :::::>
page 299, "New tires and rep lacing tires and wheels" .•
Braking
General information
What affects braking efficiency?
Operating conditions and driving habits
The brakes on today's automobiles are still subject to wear,
depending large ly on operating conditions and driving habits:::::>& .
On vehicles that are either driven mostly in stop-and-go city traffic
or are driven hard, the brake pads should be checked by your autho-
Intelligent technology
rized Audi dealer more often than specified in the Warranty & Main
tenance booklet.
Fai lure to have your brake pads inspected can
resu lt in reduced brake performance .
On steep slopes, you shou ld use the braking effect of the engine.
This way, you prevent unnecessary wear on the brake system. If you
must use your brakes, do not hold the brakes down continuous ly.
Pump the brakes at intervals.
Moisture or road salt
If you are driving faster than 31 mph (50 km/h) and the windshield
wipers are on, the brake pads will briefly touch the brake discs in
regular intervals so as to improve reaction time when braking on
wet surfaces. You , the driver, wil l not notice anything.
Under certain conditions, for example, when driving th rough water
or very heavy rain , or even after washing your vehicle , the braking
effect can be reduced due to moisture (or in freezing conditions ice)
on the brake pads. A few careful brake applications should dry off
the brake pads or remove any ice coatings .
The ef fectiveness of the brakes can be reduced when the vehicle is
driven on a salt -covered road and the brakes are not used . Here too ,
you should clean off accumulated sa lt coating from brake discs and
pads with a few carefu l applications of the brake:::::>&.
Corrosion
There may be a tendency for dirt to build up on the brake pads and
corrosion to form on the discs if the car is not drive n regularly or
only for short trips with litt le use of the brakes .
I f the brakes are not used frequently, or if corrosion has formed on
the discs, it is advisable to clean off the pads and discs by braking
firm ly a few times from a moderately high speed:::::>& .
Faults in the brake system
If you shou ld notice a sudden increase in brake pedal travel, then
one of the two brake circuits may have failed:::::>&. ..,
I t •
Page 259 of 360
_____________________________________________ C_ l_ e _a_ n_ in_ g_a _ n_d_ p_ r_ o_ t _e_ c_t _io _ n __ !II
•
T he best way to remove snow from windows and mirrors is to use a
brush . Use a non -abrasive
pla stic ice scraper -better still, a spray
deicer -to remove
ice from w indows and mirrors .
The windows must not be cleaned with insect remover or wax since
these can interfere with the function of the w inds hie ld w iper blades
(chatter).
O il, grease, or silicone res idue can be removed with
glas s cleaner or
silicone remover . However, wax residue requires the use of a
spec ially fo rmulated so lvent . Please contac t your authorized Audi
dea ler for advice on safe products for wax removal.
Windows should also be c leaned on the inside at regular interva ls .
Never dry windows with the same chamois that you use to dry
painted surfaces . Wax residue on the chamois can impair vision
t hrough the windows .
& WARNING
• Always read and heed all WARNING S and other information
=> page 252.
• The windshield mu st not be treated with water -repellent m ate
rials . They can in crea se glare under poor v isibilit y conditio ns su ch
a s wetne ss , darkne ss , or when the sun i s low on the hori zon. In
additio n, they can cau se the windsh ield wipers to chatter .
0 Note
• Never use warm or hot wat er to remove snow and ice from
windows a nd mirrors . This cou ld cause the glass to crack.
• T o prevent damage to the wires of the rear defogger, do not p lace
any adhesive stickers on the inside of the rear window over the
wires .
• To he lp prevent dirt from scratching the window, always scrape
in a forward direction -pushing the scraper away from you -never
back and forth. •
Water leaking from the inside of the rear windows may damage
sensitive e lec trical componen ts located eit her u nder the rear parcel
she lf or in the rear trunk area . Always ensure that water never leaks
t hrough the body section of the vehicle. You can do this by using
waterproof protection over the vehic le 's electrical components (e.g .
when instal ling window tinting).
• Damage or malfunction of e lectrical components due to water
damage or any other outside in fluence is no t cove red by the Audi
New Vehic le Limited Warranty. See your Warranty
& Maintenance
booklet for additional details about your war ranty. •
Weatherstrips
Complete car care includes the weatherstrips as well.
-App ly a suitable rubber cond itioner to the weatherstr ips
from t ime to ti me.
io be able sea l properly, the weatherstrips around the hood, doors,
r ear lid, etc. must rema in pliable . Spray the weatherstr ips with sil i
cone or coat them with talcum powder or g lycerin to retain the flex
ibility of the rubber and to protect them against freezing in the
winter.
& WARNING
Al ways read and heed all WARNINGS and other information
=> page 25 2.
[ i ] Tips
K eep si licone sprays off the windshield to avoid wiper smear in
ra in. •
Vehicle care I t •
Page 272 of 360
___ C_ h_ e_c _ k_ i_ n ...;:g:- a_ n_ d_ f_ il _li _n ...::g ::.- _____________________________________________ _
Checking and filling
Engine hood
Releasing the engine hood
The engine hood is released from inside the vehicle.
-Open the driver's door .
Fig. 220 Driver's side
footwell: engine hood
release lever
-Pull the release lever on the left under the instrument
panel
~ fig. 220 in the direct ion of the arrow.
The hood pops up slightly under spring pressure. •
Opening the engine hood
Fig. 221 Release lever
under the engine hood
Before opening the engine hood, make sure that the wind
shield wipers are flat against the windshield. Otherwise,
they could damage the paint on the hood.
Pull up on the release under the hood :::} fig. 221. This
releases the catch .
- Open the hood all the way:::}& .
& WARNING
Hot engine coolant can burn you.
• To reduce the risk of being burned, never open the hood if you
see or hear steam or coolant escaping from the engine compart
ment. Wait until no steam or coolant can be seen or heard before
carefully opening the hood. •
Page 355 of 360
Alphabetical index -
-------------=----
Reset button ... ...... .. ... ... . .. .. .. 11
Retractor ................. ......... 183
Rims Cast al loy ..... .. .... .... ..... .. . 258
Replacing ... .... ..... .. .... .... . 301
Roof luggage rack
Mounting points .................. 85
Roof rack ........... ...... .... .... .. 84
Roof load ...... ...... ...... ...... 85
See also Roof luggage rack ... .... .. 84
s
SA FE ... .... .... .... .... ... .... .... . 11
Safe driving hab its .. .... .... ... .... . 168
Safe ty belt position . . . . . . . . . . . . . . . . . . 184
Safety belts worn by p regnant women ..
185
Safety belt pretensioner ... .... .... ... 186
Service and disposal .............. 187
Saf ety b elt warning light .... .... .. 14,179
Safety belts . . . . . . . . . . . . . . . . . . . . . . . . 183
Cleaning ..... .... .... ........... 263
Danger to passengers who do not wear a
safe ty belt . .... .... ..... .. ... .. 181
Fastening ... .... .... .... ... .... . 183
Improperly worn ..... .... ........ 186
Not worn . . . . . . . . . . . . . . . . . . . . . . . . 181
Safety belt position ...... .... ..... 184
Safety instructions . ......... .... . 182
Securing child s afety seats ........ 223
Special considerations for pregnant women ....... .... .... ......... 185
Unfastening ..... ... ..... ...... .. 186
Controls and equip
ment Safety first
Warning
/indicator light .... ........ 179
Why YOU MUSTwearthem ... .... . 179
Worn properly ..... .... .... .... .. 182
Safety compliance sticker . .... ... .... 334
Safety equipment .... .... ..... .. .... 168
Safe ty fea tures for occupant restraint and
protection ... .. ........ .... ... . 168
Safety guidelines Seat adjustment ... ...... ... ... ... . 69
Saf ety instructions
Engin e compartm ent . .... .... ..... 271
for sid e curtain airbags . .......... . 211
for using child safety seats ....... .. 216
for using safety be lts .... .......... 182
Moni toring the Advanced Airbag System
201
Seat adjustment Driver's seat ........ ...... ... .... . 69
Easy entry function ........... ... .. 74
Easy entry manual function .. ..... .. 72
For -and -aft manua lly ..... ..... ... .. 71
Front passenger's seat .. .... ..... .. 70
Front seats ...... .. .. .... .... .... . 69
Head restraints ... ..... ... ..... .. . 173
Manual .. ...... .... ... .. ..... ... . 70
Power ....... .. .... .... .... .... .. 72
Seat back angle manually ........ ... 71
Seat height manually . ........ .... . 71
Seat belt s
See Safety belts
Seat heating 179
Front seats ...... .. .. .... .... .... 105
Seat memory ...... .. ... ... ..... .... . 74 Seating capacity
.... ..... .. . .... .. . . 179
Seating position Driver ......... ....... .. .. .... ... 170
Front passenger . ...... .. . .... .. .. 171
How to adjust the front seats ... .... 171
Incorr ect seat position .... .... .... 173
Occupan ts ... ... .. .... ...... .... . 170
Rear passengers . ...... .. . .... .. .. 172
Seats Number of seats .... .... .. .... .... 179
Se lect ive unlock feature ...... .... ..... 43
S elector le ve r .. .. .... ..... .. .... .... 149
Emergency release ...... .... ..... 154
Service and disposal
Safety belt pretensioner . ...... .... 187
Service interval display ... .... .... ... .. 21
S erv ice pos ition for w indsh ield wipers . .. 62
Servotronic Power steering .. ...... ....... .... 239
SET button . ...... .. .... .... ..... .. ... 9
Shift buttons ..... .. .... .... .... .... 153
Side airbags Description . ...... .... ....... .... 207
How they work .. ...... .... ... .. .. 208
Side assist Activating and deactivating .... .... 135
Description . ..................... 135
Informational and alert stage signals 137
Messages in instrument cluster display .
142
MMI settings ............... ...... 141
Operation .... .... ... ... ... .. .... 137
Vehicle operation Vehicle care Do-it-yourself service Technical data
Page 358 of 360
___ A_l.:,. p _h_ a_ b_e _t _ic _ a_l _in _ d_e _x ____________________________________________ _
Glossary of tire and loading terminology
288
New tires and wheels . . . . . . . . . . . . . 299
Tires and vehicle load limits ... .... 295
When must a safety belt be replaced? . . 182
When must the airbag system be inspected? 199
When should I adjust the tire pressures?
294 T
ires ... .. .... ..... .. ... ... .... . 240
Windows .. ... ...... ...... ...... 256
Winter tires ...... ...... .... ... .. ... 304
All -wheel drive ................ ... 304
Wiper blades Installing new wipe r blades ..... .... 63
X
When should I check the tire pressures? 294 Xenon headlights ....... ...... ... 56, 324
Where can I find the tire pressures for my
car? .......................... 293
Why safety belts? . . . . . . . . . . . . . . . 179 , 180
Window regulators Malfunctions ...... .... ........... 50
Power locks ........... .. .... .... . 49
Windows Cleaning ........................ 256
Windshield defogging/defrosting 95, 102
Windshield washer fluid Low level ... .. .... .... ...... ... .. 35
Windshield wiper Insta lling new wiper b lades ......... 63
Windshield wipers .... ....... ....... . 61
Faulty ... ................ .... .... 37
Service position . . . . . . . . . . . . . . . . . . 62
Washer reservoir . . . . . . . . . . . . . . . . . 286
Winter operation Battery . . . . . . . . . . . . . . . . . . . . . . . . . 281
Coolant system ............. .... . 277
Defrosting windows ... ...... .. 95, 102
Front seat heating . . . . . . . . . . . . . . . . 105
y
Yellow symbols .. ....... ....... .. .... 32