page 76 AUDI A5 COUPE 2013 Owner's Guide

Clear vision Lights
Switching the lights on and off
F ig . 34 Instrument pane l: headlight control switch
Light switch ·'t/,·
Turn the switch c> fig. 34 to the correspond ing
position . When the lights are switched on, the
:oo: symbol turns on.
0 • The lights are off or the daytime running
lights are on:
-USA mod els : The daytime running lights are
activated when the light switch
c> fig . 34 is
in the
O position or the AUTO position (only
in daylight conditions) . The daytime running
lights function can be turned on and off in
the radio or MMI* menu
E xterior li ghtin g
¢ page 44 , c> &_.
-Ca nada mod els: The daytime runn ing lights
are activated when the light switch
¢ fig . 34
is i n the O position, :oo : position or the AUTO
posit ion (on ly in daylight cond itions). The
daytime running lights function cannot be
turned off¢&. .
AUTO* -Automatic headlights switch on and
off depending on b rightness, for example in
tw ilight, during rain or in tunnels ¢,& .
:oo: -Side marker lights
~D -Low beam headlights
Fog light s/rear fog ligh t(s)*
Press the appropriate button c> fig. 34:
1D -Fog lights
0$ -Rear fog light(s)
Clear vi sion 43
adaptive light*
When switched on, adaptive ligh t adap ts to
curves in the road depend ing on the vehicle
speed and the steering angle. This provides
better lighting through the curve. The system
operates at speeds between approximately
6 mph (10 km/h) and 68 mph (110 km/h).
Static corner ing light * (vehicles with adaptive
light) -the cornering light switches on at
speeds up to approximately 25 mph (40 km/
h) when a certain steering wheel angle is
reached or when a turn signal is activated. The
area to the s ide of the vehicle is illuminated
better whe n turn ing .
The adaptive light and the cornering light only
function when the switch is in the AUTO posi­
tion (automatic headlights*) .
A WARNING
-Daytime running lights and automatic
headlights* are only intended to ass ist
the driver . T hey do no t re lieve the driver
of his responsibility to chec k the head ­
lights and to t urn them on manua lly ac­
cording to the current light and visibility
conditions. For example, fog cannot be
detected by the light sensors*. So a lways
switch on the headlights
~D under these
weather conditions and when driving in
the dark .
- Cras hes can happen when you cannot see
the road ahead and when yo u cannot be
seen by other motorists. Always turn on
the head lights so that you can see ahead
and so that others can see your car from
the b ack.
- Please obey all laws when using the
lig hting sys tems described here.
(D Note
The rear fog lights* should on ly be turned
on in accordance with t raff ic regulation, as
the lights are bright for following traffic. ..,.

44 Clear vis ion
@ Tips
- The light sensor* for headlight control is
located in the rear view m irror mount.
You should therefore not apply any st ick­
ers to the windsh ield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted
c> page 44.
- When you remove your key from the igni­
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the driv­
er's door is open .
- In cool or damp weather, the ins ide of
the headlights, turn signals and tail lights can fog over due to the tempera­
ture difference between the inside and
outside. They will clea r shor tly after
switching them on. This does not affect
the service life of the lighting.
- In the even t of a light sensor malfunc­
tion, the driver is no tified in the instru­
ment cluster disp lay¢
page 22.
Turn signals and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher .
Fig. 35 T u rn s ig na l and h ig h beam leve r
Turn sign als ¢i ¢
The turn signals activate when you move the
l ever into a turn s ignal pos ition when the ign i­
tion is switched on.
(D -right turn signal
@-left tur n signa l
The turn s ignal blinks three times if you just
tap the lever .
High be ams and headlight flasher [D
Move the lever to the correspon ding posit io n:
@ -high beams on
@ -high beams off or headlight flasher
The indicator light
II in the i nstr ument clus­
te r turns on .
Notes on thes e features
- The turn signals on ly work w ith the ign ition
t ur ned on. The indicator lights
B or II in
t he instrument cluster also blink.
- After you have turned a co rner, the tu rn s ig­
na l switches off au toma tically .
- The
high beam works on ly w hen the head­
lights a re o n. The ind icator light
II in the
instrument cluster ill uminates when the
high beams are on .
- The
headligh t flasher works only as long as
you ho ld the lever -even if the re a re no
lights switched on . The ind icator light
II i n
the instrument cluster illuminates when you
use the headlight flasher.
A WARNING
--
Do not use the h igh beam or headlight
flashe r if you know that these could blind
oncom ing traffic.
Adjusting exterior lighting
The functions ore selected in the radio or
MMI" .
.,. Select: I CAR ! function button > Ext erio r
light ing .
Or
.,. Select: !CAR I function button> Car S ystems
control button > Ve hicle s etting s> Exterior
lighting .
Coming home (light when leav ing car }*,
Leav ing home (light when unlocking car )*
The coming home function illuminates the
area around the vehicle when the ignition is
switched off and th e dr ive r's door is open ed.
Depend ing on veh icle equ ipment, the function
can be switched on and off or the length of
time the lig hts remain on* can be ad justed . ..,.

The leavin g home function il luminates the
area around the vehicle when unlocking it.
This function can be switched on and off.
The
c o ming h om e and lea ving home func­
tions on ly operate when it is dark and the
light switch is in the AUTO position
¢ page 43, fig. 34.
Auto headlight s*
When the light switch is in the A UTO
¢
page 43 position, the switch-on po int of the
lights can be changed in the automatic driving
light function.
Daytime running lights
USA m odel s:
You can switch the dayt ime run­
ni ng lights
on and o ff .
Canada mod els:
The function cannot be
turned off .
It is activated a utomat ica lly each
time the ignition is switched on.
Travel mode*
The headlight beam is asymmetrical. This pro­
v ides stronger illum ination on the side of the
road on wh ich you are driving .
If you are driv­
i ng in a count ry that d rives on the opposite
side of the road from your own country, th is
will cau se glare for on coming dr ivers. To pre­
vent glare:
- Trave l mode must be selected in vehicles
with Xenon headlights*.
- In veh icles with halogen headlights, ce rtain
areas of the head light lenses must be cov­
ered w ith wate rproof adhesive covers that
prevent light from passing thro ugh. Fo r
more information, please see your author ­
ized Audi dea ler or author ized repa ir faci lity .
(D Tips
When trave l mode is activated, a display in
the dr iver information system indicates
this each time you switch the ignit io n on.
Clear vi sion 45
Emergency flashers
F ig. 36 Center console: emergency flasher switch
The emergency flashers makes other moto­
rists aware that you or your vehicle are in an
emergency situation .
.,. Press the switch ~¢
fig. 36 to turn the
emergency flashers on or off.
When the emergency flas hers are on, all four
turn signals b link at the same time. The turn
s ignal indicator lights
1111 in the instrument
cluster, as well as the light in the emergency
flasher switch ~ blink likewise.
You can indicate a lane change or a t urn w hen
the emergency flashers are switched on by us­
ing the turn signal lever. The emergency flash­
ers stop temporarily.
T he emergency flashers also work when the
ignition is turned off.
T he emergency flashers wi ll turn on a utomat i­
ca lly if yo u are in an accident where the airbag
has deployed.
(D Tips
You sho uld turn on the emergency f las hers
when:
- yo u are the last veh icle standing in a t raf ­
fic jam so that any other vehi cles coming
can see you, or whe n
- your vehicle has bro ken down or you are
in an emergency s ituation, o r when
- yo ur vehicle is be ing towed by a tow
truck or if you are tow ing another vehicle
beh ind you.

Turn the knob to the desired position:
Q/ P -In th is position , you can adjust the
d river's and front passenger's ex ter io r mir ro rs
by turning the knob in the des ired direc tion.
(ijjl -The mirrors are heated depending on the
ou tside temperature.
P assenger exter ior mirro r tilt function*
( only with memory for exterior mirrows)
To help yo u see the curb when backing into a
pa rking space, the surface of the m irror tilt s
slig htly . The knob m ust be in the P posit io n
for this to ha ppen .
You can adjust the t ilt ed mir ro r sur face by
turn ing t he knob in the des ired direction .
When you move out of reve rse and into ano th­
er gear, the new mi rror posit ion is stored and
assigned to the key you are using .
The mirro r goes back into its origina l posit io n
once yo u drive forward faster tha n 9 mph
(15 km/h) or sw itch the ignition off .
,&. WARNING
Curved mirror su rfaces (convex or spheri ­
cal *) increase yo ur field of view . Remem­
ber that vehicles or other objects will ap­
pea r smaller and farther away than w hen
seen in a flat m irr or. If you use this mirror
to estimate distances of following veh icles
when changing lanes, you co uld estimate
incorrectly and ca use an accide nt.
(D Note
- If you wash the veh icle in an automatic
ca r wash, yo u must fold the exte rior m ir­
r o rs in to reduce the r is k of damage to
the m irrors .
(D Tips
-The exterior mirror setti ngs are sto red
with the memory functio n* ~
page 57 .
- If there should be a malfunction in the
electr ica l system, you can st ill adjust the
exter ior mir ro rs by press ing the edge of
the mi rror.
-
Clear vi sion 4 7
Dimming the mirrors
N
~
><
~===~=======~ ~
Fig. 41 Auto matic dimmin g rearv iew mirro r*
Manu al d imming rearview mir ror
.,. Pull the lever on the bottom of the mirror
back .
Automat ic dimming rearview mirror*
.,. Press the button@~ fig. 41. The indicator
light @ turns on . The rearview and exterio r*
mi rrors dim a utomatically when light shines
on them, for example from headlights on a
veh icle to the rear .
A WARNING
-
Electrolyte fluid can leak from aut omatic
d imm ing mirrors if the glass is broken .
E lec trolyt e fluid can irritate skin, eyes and
res pirato ry system.
- Repeated or prolonged exposu re to elec­
trolyte can ca use i rritation to the respira­
to ry sy stem, especially among people
wit h asthma or o ther resp iratory co ndi­
tions . Ge t fresh a ir immediately by leav­
ing the vehicle o r, if that is no t possib le,
open w indows and doors all the way.
- If electroly te gets in to the eyes, f lush
them thorough ly with large amounts of
clean water for at least 15 minutes;
medical attention is recommended.
- If electrolyte contacts skin, fl ush affect­
ed area with clean water for at least 15
minutes a nd the n wash affected area
wit h soap and water; medical attention
is recommended. Thoroughly wash af­
fected cloth ing and shoes before re use .
.

@ Tips
-Pressing the button~ several times
consecutively can trigger the overload protection. The sun shade can only be ex­
tended/retracted again after a brief wa it­
i ng per iod.
- The rear window sun shade only func­
tions when the veh icle inter ior is warmer
than 14°F (-10°C).
Wiper and washer system
Switching the windshield wipers on
Fi g. 45 Windshield wiper lever
Move the windshield wiper lever to the corre ­
spond ing position:
@ -Windshie ld w iper
off
CD -Interval mode. To extend/shorten the
wiper intervals, move the switch @to the
l eft/right. I n veh icles with a rain sensor* the
wipers turn on in the ra in once the vehicle
speed exceeds approximate ly 2 mph (4 km/h).
The highe r the sensitivity of the rain sensor* is
set (switch @to the right), the earlier the
windshie ld w ipers react to moistu re on the
windshie ld. In some models, you can switch
rain sensor mode
off and switch intermittent
mode on in the MMI*. Select:
ICAR I funct ion
button
> Car Systems contro l button > Driver
as sis t > Rain s en sor .
In inte rmittent mode '
you can adjust the interval time using the @
sw itch.
@ -Slow wip ing
® -Fast wiping
Clear vi sion 49
@ -Single wipe
® -C lean the w indshie ld. To elim ina te wate r
drople ts, the windsh ield w iper pe rform s one
afterw ipe operation after severa l se conds
whi le dr iving. You can sw itch this f unction
off
by moving the leve r to positio n® within 10
seconds of the afterwipe operat ion . The after ­
wipe function is reactivated the next t ime the
ignition is switched on .
Cleaning the headlights* . The headlight wash­
er system * operates only when the headlights
are o n. If you move the lever to position @,
the headlights are washed in intervals.
A WARNING
- The rain senso r is only intended to assist
the dr iver. The d river is st ill responsib le
for manually switc hing the wipers on ac­
cording to the vi sibility cond itions.
- The windsh ield may not b e treated with
wate r-repell ing windsh ield coating
agen ts. Un fa vo rable cond iti ons, s uch as
we tnes s, d arkn ess, low sun, can result in
increased g lare. Wiper blade c hatter is
a lso possib le .
- P rope rly f unct io ni ng win dsh ield wipe r
b lades are re quired for a clear view and
safe driving
~ page 50, Replacing
windshield wiper blades.
(D Note
- I n the case of frost, check whethe r the
w indshield wiper blades are frozen to
the winds hield. Switchi ng on the wind­
shield wipers can damage the wiper
blades!
- Pr ior to using a car wash, the windshield
w iper system must be sw itched
off ( lever
in posit ion @). T his he lps to prevent un­
intentional switching on and damage to
t he windsh ield wiper system.
@ Tips
- The windshiel d w ipers are switched off
when the ig nition is tu rned off. Act ivate
t he windsh ield wipers after the ignition

50 Clear vis ion
is sw itched b ack on by mov ing the
winds hield wiper lever to any position .
- Worn or dirty windshie ld wiper b lades
r es ult in streaking. This can affect the
rain sensor* function. Check your wind­
shield wiper b lades regularly.
- The was her fluid nozzles of the wind­
s h ield washer system are heated at low
temperatures when t he ignit ion is on.
- When stopping temporarily, (e .g . at a
traff ic light) the set speed of the wind­
shield wipers is automatically red uced by
one speed.
Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear.
F ig . 4 6 Remov ing windshie ld w iper blade
Wiper service position /blade replacement
position
.. Swi tch the w indshield wiper s off (posi tion
@ ¢page 49, fig. 45).
.. Se lect:
ICARI f u nct ion button > Wind shield
wipers
> Ser vice po sition > on . Or
.. Se lect:
I CARI f u nction button > Car sy stem s
control button > Servicing & checks > Wiper
service position > On .
The windsh ield wipers
move into the service position .
Removing the wip er blade
.. Lift the w indshield wiper arm up from the
windshield.
.. Press the locking knob(!)¢ fig. 46 on the
wiper blade. Hold the wiper blade firm ly.
.. Remove the w iper blade in the direction of
the arrow .
Attaching the wipe r blade
.. Inst all the new wiper blade in t he reta iner
on the wiper a rm @ unt il you hear it click in ­
to p lace on the wiper arm.
.. Place the wiper arm back on the winds hield.
.. To bring the w ipers back into the original
position, press the windshield wiper lever .
Or
.. Select:
!CAR I function button> Windshield
wip ers
> Service po sition > off . Or
.. Select:
!CAR I function b utton> Car sy stem s
cont ro l butto n > Servicing & che cks > Wip er
s ervi ce po sition
> Off .
A WARNING
=
-If the windshie ld wipers smea r the wind-
shie ld, clean the wiper b lades with wind­
shie ld washer fluid. If the wiper blades
are ext remely dirty, you can a lso clean
them with a soft sponge o r cloth.
- For your safety, you shou ld replace the
wiper blades once or twice a year. See
your author ized Audi dealer for replace­
men t blad es.
(D Note
- The windshie ld w iper blades m ust only
be replaced when in the service pos ition!
Otherw ise, you risk damag ing the pa int
on t he hood o r the windsh ie ld w iper mo­
to r.
- Yo u should not move your veh icle or
press the windsh ield wiper lever when
the wipe r arms are folded away from the
w indshield. The winds hield wipers wo uld
move back into their or iginal position
and co uld damage the hoo d and wind ­
shield.
- T o help preven t damage to the w iper sys­
t em, always loosen blades w hich are fro ­
zen to the windshield before operating
w ipers .
- To help prevent damage to wiper b lades,
do not use gasoline, kerosene, paint
thinne r, or other solvents on or near the
w iper blades.

Seats and storage
General recommen­
dations
Why is your seat adjustment so important?
The safety belts and the airbag system can
only provide maximum protection if the front
seats are correctly adjusted.
There are various ways of adjusting the front
seats to provide safe and comfortable support
for the driver and the front passenger. Adjust
your seat properly so that :
- you can easily and quick ly reach all the
switches and controls in the instrument
panel
- your body is properly supported thus reduc­ ing physical stress and fatigue
- the safety belts and airbag system can offe r
maximum protection
¢ page 142.
In the following sections, you will see exactly
how you can best adjust your seats .
There are special regulations and instructions
for installing a child safety seat on the front passenger's seat. Always follow the informa­
tion regard ing child safety provided in
¢ page 166, Child Safety.
.&_ WARNING
-
Refer to ¢ page 124, Driving Safely for
important information, tips, suggestions
and warnings that you should read and fol­
low for your own safety and the safety of
your passengers.
.&_ WARNING
Incorrect seating position of the driver and
all other passengers can result in serious
personal injury.
- Always keep your feet on the floor when
the vehicle is in motion -never put your
feet on top of the instrument panel, out of the w indow or on top of the seat cush­
ion. This app lies especially to the passen-
S eat s an d sto rage 53
gers . If your seating position is incorrect,
you increase the risk of injury in the case
of sudden braking or an accident . If the
airbag inflates and the seating position
is incorrect, this cou ld result in pe rsonal
in jury or even death.
- It is important for both the driver and front passenger to keep a distance of at least 10 inches (25 cm) between them­
selves and the steering wheel and/or in­
strumen t panel. If you're s itting any
closer than th is, the airbag system can ­
not protect you properly. In addition, the
front seats and head restraints m ust be
adj usted to your body height so that they
can give you max imum protect ion.
- Always try to keep as much distance as
possible between yourself and the steer­
ing wheel or instrument panel.
- Do not adjust the driver's or front pas­ senger's seat whi le the vehicle is moving.
Your seat may move unexpectedly, caus­
ing sudden loss of veh icle control and
pe rsonal injury. If you adjust you r seat
while the veh icle is moving, you are ou t
of posit ion.
Driver's seat
The correct seat position is important for safe
and relaxed driving .
We recommend that you adjust the dr iver's
seat in the follow ing manner:
.., Adjust the seat in fore and aft direction so
that you can easily push the pedals to the
floor wh ile keeping your knees slightly bent
¢ .&, in Why is your seat adjustment so im ­
portant? on page 53.
"" Adjust the seatback so that when you sit
w ith your back against the seatback , you can
s ti ll grasp the top of t he steering wheel.
... App lies to vehicles with adjustable head re­
straints: Adjust the head restraint so the up­
per edge is as even as possible wit h the top
of your head. If that is not possib le, try to
adjust the head restraint so that it is as .,.

54 Seats and storage
close to this position as possible
¢page 56.
A WARNING
Never place any objects in the driver's foot­
well. An object could get into the pedal area and interfere with pedal function. In
case of sudden braking or an accident, you
would not be able to brake or accelerate .
Front passenger's seat
Always move the front passenger seat into
the rearmost position .
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instru­
ment panel than necessary and always wear
the three-point safety belt provided adjusted correctly . We recommend that you adjust the
passenger's seat in the following manner:
• Bring the backrest up to an (almost) upright
position. Do not ride with the seat reclined .
• Applies to vehicles with adjustable head re­
straints: Adjust the head restraint so the up­
per edge is as even as possible with the top
of your head . If that is not possible, try to
adjust the head restraint so that it is as
close to this position as possible
¢ page 56.
• Place your feet on the floor in front of the
passenger's seat.
Front seats
Power seat adjustment
Applies to vehicles: with power adjustab le seats
Fig. 49 Front seats: powe r seat adjustme nt
Controls
@ -Adjusting the lumbar support* : press the
button in the corresponding position ¢ .&, .
@ -Moving the seat up/down: press the but­
ton up/down ¢ .&, .
@ -Moving the seat forward/back : press the
button forward/back ¢.&, .
©-Adjusting the backrest angle: press the
button forward/back ¢.&, .
©-Raising/lowering * the head restraints:
press the button up/down¢.&, .
@ -Lengthening/shortening the upper thigh
support* : lift the handle. A spring moves the
front seat cushion forward ¢ .&, .
A WARNING
---Never adjust the driver's or front pas ­
senger's seat while the vehicle is moving.
If you do this while the vehicle is moving,
you will be out of position . Always adjust
the driver's or front passenger's seat
when the vehicle is not mov ing.
- Be careful when adjusting the seat
height . Check to see that no one is in the
way, or serious injury could result!
- Because the seats can be electrically ad­
justed with the ignition off or with the
ignition key removed, never leave chil­
dren unattended in the vehicle. Unsuper­
vised use of the electric seat adjust­
ments may cause serious injury.
- To reduce the risk of injury in the case of
sudden braking or accident, front pas ­
sengers must never ride in a moving ve­ hicle with the backrest reclined. Safety
belts and the airbag system only offer maximum protection when the backrest
is upright and the safety belts are prop­
erly positioned on the body. The more
the backrest is reclined, the greater the
risk of personal injury from an incorrect
seating position and improperly posi­
tioned safety belts.

56 Seats and storage
Center armrest
The center armrest can be adjusted to several
levels.
Fi g. 52 Armrest between t he driver's/front passe nger's
seats .
Adju sting th e ce nter armr est
.. To adjust the angle, raise the armrest from
the start ing pos ition
¢ fig . 52 detent by de­
tent.
" To bring the armrest back into the starting
pos ition, raise it out of the top detent and
fold it back down .
The armrest can sl ide forward and back .
Head restraints
Front head restraints
Applies to vehicles: with a djustable head restrain ts
Head restraints that are adjusted according
to body size, along with the seat belt , offer
effective protection.
F ig . 53 Ma nua l front seat : adjusting the head re­
st raints
Fig. 54 Power front seat: adjusting the head restraints
Adjust the head restraint so the upper edge is
as even as possible with the top of your head.
If that is not possible, t ry to adjust the head
rest raint so that it is as close to this position
as possib le
¢ page 56 .
.,. To adjust the height of the manual head re­
straint*, grip the head rest raint on the sides
w ith both hands and slide it up/down until it
locks in to p lace
¢fig. 53.
"' To adjust the height of the power head re­
straint*, press the button up/down
¢ fig. 54.
Refer to¢ page 12 7, Proper adjustment of
head restraints
for guidelines on how to ad­
just the height of the front head restraints to suit the occupant's body size.
A WARNING
- Driving without head restraints or with
head restra ints that are not properly ad­
justed increases the risk of ser ious or fa­
tal neck inju ry dramatica lly.
- Read and heed all WARNINGS
¢page 127.
@ Tips
-To prevent the head restra ints from run­
ning into the headliner, they retract au­
tomatically when moving the seat for­
ward or upward .
- Correctly adjusted head restraints and
safety belts are an extremely effective
combination of safety featu res.

Rear head restraints
Fig. 55 Rear seats : head restraint
Fig. 56 Rear head restra ints: re lease
Adjusting the head restraints
• To move the head restraint up, hold it at the
s ides with both hands and slide it upward
until you feel it click into place¢.,&.
• To move the head restraint down , press the
button @¢
fig. 55 and slide the head re­
stra int downward .
Removing the head restraints
• Fo ld the backrest forward ¢ page 63.
• Move the head restraint upward as far as it
can go.
• Press the release@¢
fig. 56 with the me­
chanical key¢
page 34 and the button @
¢
fig . 55 . Pull the head restraint out of the
backrest at the same time¢.,& .
Installing the head restraints
• Slide the posts on the head restra int down
into the guides until you feel the posts click
into place .
• Press the button @ ¢
fig. 55 and slide the
head restraint al l the way down. You shou ld
not be able to pull the head restra int o ut of
the backrest.
Seats and storage 57
So that the driver can have a better view to
the rear, the head restraints should be pushed
down completely when the rear seats are not
occupied.
A WARNING
- Read and heed all WARNINGS
¢page 127.
-On ly remove the rear seat head restraints
when necessary in order to install a child
seat ¢
page 174. Install the head re­
straint again immediately once the child
seat is removed. Driving without head re­
straints or with head restraints that are
not properly adjusted increases the risk
of serious or fatal neck injury dramatical­
ly.
- Vehicles with a pass through in the cen­
ter conso le have seating for four. The
long center conso le between the two
rear seats is
not a seating position .
Therefore, a safety belt is not provided.
@ Tips
Correctly adjusted head restraints and
safety be lts are an extreme ly effective
combination of safety features.
Seat memory
Description
Applies to vehicles : with memory fun ctio n
The memory function allows you to quickly
and easily store and recall personal seati ng
profiles for the driver. The memory function is
operated through the master key and the
memory buttons in the driver's door.
The driver's seating profile is stored and as­
signed to the master key each time the vehicle
is locked. The seating profile is recalled auto­
matically when the vehicle is unlocked.
If two
people use one vehicle, it is recommended
that each person always uses "their own" master key.
Up to 2 seat profi les can be stored in the
memory buttons in the driver's door. Once