oil AUDI A6 1998 C5 / 2.G 01E Transmission Final Drive Differential Remove And Install Workshop Manual

39-113


3 -
Outer race for large tapered roller bearing
1) Driving out Fig. 7 , Page 39
-129
Driving in Fig. 8 , Page 39
-130
4 -
Shim "S1"
Note thicknessAdjustment overview Page 39
-150
5 -
Cover for final drive
1)
With sealReplace O-ringLubricate O-ring with oil when installing
6 -
Torx bolt, 25 Nm
7 -
Seal, right Replacing Page 39
-98
8 -
Hex socket head bolt, 25 Nm
Pa
ge 2 of 8 Differential, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.16

39-114


9 -
Drive flange, right
Removing and installing Fig. 1
10 -
Oil filler plug, 35 Nm
11 -
Differential with ring gear
1)
Disassembling and assembling Page 39
-120

12 -
Oil drain plug, 35 Nm
13 -
Bushing
Holds magnet in positionKnock in onto stop
14 -
Magnet
15 -
Outer race for small tapered roller bearing
1) Knocking out Fig. 1 , Page 39
-126
Pressing in Fig. 2 , Page 39
-126Pa
ge 3 of 8 Differential, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.16

39-118

Removing and installing differential

Rear final drive removed

Special tools, testers and auxiliary items
Drip tray V.A.G 1306

Removing

- Secure complete rear final drive on a repair
stand Page 39
-108
.

- Place drip tray V.A.G 1306 underneath and
drain oil.

- Fill space between sealing lip and dust lip with
sealing grease G52 128 A1.

- Remove left and right-hand drive flanges.
- To loosen securing bolt, screw two bolts into drive flange and counter-
hold with a lever.
- Mark drive flanges (for left and right sides).
- Pull out drive flange using the bolts already screwed in.
- Unscrew securing bolts from cover for final drive.
- Take cover for final drive off axle housing and remove differential.
Pa
ge 7 of 8 Differential, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.16

39-119

Installing
Installation is carried out in the reverse order,
when doing this note the following:

- Insert differential.

- Replace O-ring for cover for final drive and oil
when installing.

- Fit cover for final drive on final drive housing and
tighten in diagonal sequence to 25 Nm.

- Replace drive flange oil seals Page 39
-98
.

- Fill space between sealing and dust lips with
sealing grease G52 128 A1.

- Install drive flanges and tighten to 25 Nm.
- Top-up gear oil in rear final drive and check oil level Page 39
-80
.
Pa
ge 8 of 8 Differential, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.16