AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual A6 1998 C5 / 2.G AUDI AUDI https://www.carmanualsonline.info/img/6/988/w960_988-0.png AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual

Page 1 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual 13-4
 
  
Cylinder block, crankshaft and 
flywheel, servicing Notes: 
 
Always replace seals and O-rings.
 The engine speed sensor is installed in the 
transmission bellhousing with a spacer washer 
u

Page 2 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual 13-5
 
  
4 - 
Connecting rod bearings 
Do not interchange used bearing shellsConnecting rods, connecting rod bearings 
 page13
-33
 
5 - 
Piston rings 
Checking  page 13
-29
6 - 
Pistons 
Checking  p

Page 3 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual 30 Nm (22 ft lb)
Pa
ge 3 of 33 C
ylinder block, crankshaft and fl
ywheel, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.13.2

Page 4 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual 13-6
 
  
12 - 
Thrust washer 
Measuring crankshaft axial clearance   
page 13
-25
 
Only on 4th crankshaft bearing
13 - 
Special bolt (12-sided) Always replaceDriveplate: 60 Nm (44 ft lb) + additiona

Page 5 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual Replacing  page 13
-18
Pa
ge 5 of 33 C
ylinder block, crankshaft and fl
ywheel, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.13.2

Page 6 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual 13-7
 
  
19 - 
Bolt 
10 Nm (7 ft lb)
20 - 
Bolt 25 Nm (18 ft lb)Install hand-tight before fully tightening
21 - 
Cylinder block 
Pa
ge 6 of 33 C
ylinder block, crankshaft and fl
ywheel, servicin
g
11

Page 7 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual 13-8
      
Ribbed belt, removing and installing
 
     
Lock carrier in service position   page 13
-1 
     
CAUTION! 
     
Before removing ribbed belt, note direction of 
rotation with chalk or fel

Page 8 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual 13-9
 
    
Note:  
Observe previously marked direction of rotation of belt and that it is 
seated correctly on the pulley.  -  Counterhold pulley for viscous fan using 3212 spanner wrench and 
remove

Page 9 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual 13-10
      
Installing  
    
Note:  
Observe previously marked direction of rotation of belt and that it is 
seated correctly on the pulley. 
Routing of ribbed belt:  -  First install ribbed belt on

Page 10 of 33

AUDI A6 1998 C5 / 2.G AHA ATQ Engines Cylinder Block Crankshaft And Flywheel Component Service Manual 13-11
      
Vibration damper, removing and 
installing
 
     
Lock carrier in service position   page 13
-1 
      Ribbed belt, removing and installing   page 13
-
8 .  
     
Note:  
     To remove
Page:   1-10 11-20 21-30 31-40 40 next >