AUDI A6 2012 Owner's Manual

Instruments and warning/indicator lights 19
!;.!~ Electronic stabilization program
(ESP)
This warning/indicator light monitors the
electronic stabilization program.
When you sw itch the ignition on, the indicator
light
G1 turns on briefly to check the function .
If thE:
G1 indicator lamp blinks while dr iving,
the ESP or ASR (Ant i- Slip Regulation) is active ­
ly regulating.
If thE:
hJ indicator lamp illuminates, the sys­
tem has switched the ESP off.
If the indicator light
I turns on, the ESP was
switched to ESP sport mode with the button
I!]<=>
page 189. If this is case, you can reacti­
vate the ESP by switching the ignition off and
then on again . The warning/indicator light
should go out to show that the system is fully
functiona l again.
Stability program and ABS fault! See own­
er's manual
If the indicator light D] and the ABS indicator
light
m (USA mode ls) ;fl] (Canada models)
turn on and the message appears, there is a
malfunct ion in the ABS system or electron ic
differential lock . This also interrupts the ESP.
The brakes still function with their normal
power, but ABS is not active.
Drive to your authorized Aud i dealer immedi ­
ately to have the malfunction corrected .
If the battery term inals were disconnected
and re-connected, the vehicle was jump start­
ed or the battery is very weak, the ESP sensor
system goes through a learning process for
the first few yards . The warning/ind icator
light illuminates . Th e warn ing/ indicator light
goes o ut as soon as the learning process is
comp lete.
For more informat ion about the ESP
<=> page 189. ABS/(
8) Anti-lock braking system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL) .
The warning/indicator light B (USA mod­
els)
/ l(O] (Canada models) w ill come on for a
few seconds when the ignition is sw itched on .
The light will go out after an automatic check
sequence is comp leted.
There is a malfunction in the ABS when:
-The warning/indicator light does not illumi·
nate when you switch the ignition on.
- The warning/indicator light does not go out
after a few seconds.
- The warning/indicator light illuminates
while driving.
The ESP indicator light also illuminates if
there is a ma lfunction in the ABS . The mes ­
sage
Stability program and ABS fault! See
owner's manual
a lso appears in the instru­
ment cluster d isp lay and a warning tone
sounds .
The brake system will still respond even
without the assistance of the ABS system.
See your authorized Audi dealer as soon as
possible to restore full braking performance.
Fo r more information regarding the ABS
<=>page 189.
Malfunction in the brake system
If the brake warning light<=> page 14 and the
ABS warning illum inate
together there may be
a malfunction in the ABS, and there may also
be a malfunction in the brake system itself
<=>
&. . The ABS will not work and you will no­
tice a change in braking response and per·
formance .
In the event of a malfunction in the brake
system
the warning/indicator light _
(USA models)/ . (Canada models) in the in­
strument cluster flashes <=>
page 14.
Malfunction in the electronic differential
lock (EDL)
T he EDL works t ogether w ith the ABS. The
ABS warning light will come on if there is a

20 Instrum ent s a nd w arn in g/i ndic ato r light s
malfunction in the EDL system c> page 189 .
See your authorized Audi dealer as soon as possib le.
A WARNING
- If the 9 (USA mode ls)l ii] (Canada
models) warning light does not go out,
or if it comes on while driving, the ABS
system is not working properly . The vehi­
cle can then be stopped only with the
standard brakes (without ABS). You will
not have the protection ABS provides.
Contact your Audi dealer as soon as pos­
sible.
- USA models: If the - warning l ight,
the
ljJ warning light and the m warn­
ing light come on together, the rear
wheels could lock up first under hard braking. Rear wheel lock-up can cause
loss of vehicle control and an accident .
Have your vehicle repaired immediately
by your authorized Aud i dealer or a quali ­
fied workshop . Drive slowly and avoid
sudden, hard bra ke applications.
- Canada models:
If the brake warn ing
light ., the
DJ wa rning light and the
ABS warning light
ii] come on together,
the rear wheels could lock up fi rst under
hard bra king. Rear wheel lock-up can
cause loss of vehicle control and an acci­ dent. Have your vehicle repaired immedi ­
ately by your authorized Audi dealer or a
qualified workshop. Dr ive slowly and
avo id sudden, hard brake applicat ions.
{0) Worn brake pads
El Brak e pad s!
If the warning light illuminates, immediately
contact your authori zed Audi dealer or quali ­
fied workshop to have all brake pads inspect­ ed . On USA models the warning light
El
comes on together with the warn ing light
- · Both sets of brake pads on an axle
must always be replaced at the same time.
l ) - : USA m od els only
A WARNING
Driving w ith bad brakes can cause a colli­
sion and ser ious personal injury .
- If the warn ing light
El and the warning
light
- l) with the message Brake
p ads!
comes on in the instrument cluste r
d isp lay, immediately contact your au­
thor ized Audi dealer or qualified work­
shop to have all b rake pads checked or
replaced if necessa ry.
EPC Electronic power control
This warning/indicator light monitors the
electronic power control.
The ~ warning/ind icator light (Electronic
Power Cont rol) illuminates when you sw itch
the ignit io n on as a function check.
-
© Tips
If this warn ing/ indicato r light illum inates
while you are driving, then there is a mal­
fun ct io n in the engine electronics. Have
the malf unct io n corrected as soon as pos­
s ib le by your au thorized A udi dealer or
qualified repa ir facility .
o Malfunction Indicator Lamp (MIL )
The Ma lfunction Indicator Lamp (MIL) is part
of the On-Board Diagnostic (OBD II) system.
The symbol
f• lights up when the ign ition is
switched on and will turn off after the engine
has started and has settled at a constant idle
speed . This indicates that the MIL is work ing
properly.
The warning light illuminates when there is a
malfunction in the engine electron ic system .
Contact your authorized Audi dea ler and have
the malfunction cor rected.
An improperly closed fuel filler cap may a lso
cause the MIL light to illuminate
c> page 217 .
For more information
c> page 28.

Instruments and warning/indicator lights 21
!?i Engine speed limitation
A ppl ies to vehicles: wit h en gin e s pee d l im itat ion
(II Engine speed maximum XXXX RPM
The engine speed is automatically limited to
the speed displayed in the driver information
system. This protects the engine from over­ heating.
The engine speed limitation deactivates once
the engine is no longer in the critical tempera­
ture range and you have released the accelera­
tor pedal once.
If the engine speed limitation was activated by an engine control malfunction, the indica­
tor light~ also turns on. Make sure that the
speed does not go above the speed displayed.
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
~ . Engine oil level
II Add oil, max. x qt (l). You may continue
driving
When the symbol Ill and driver message ap­
pear, add the amount of oil appearing in the
display at the next opportunity ¢
page 225.
~ .... Engine oil sensor
II Oil level! Sensor defective
If the symbol illuminates, contact your au­
thorized Audi dealer and have the oil sensor inspected. Until you have this done, check the
oil level each time you refuel just to be on the
safe side¢
page 225.
Bil Fuel level indicator
Ii Please refuel
If the indicator light turns on for the first
time and the message appears, there are
about 2.6 gallons (10 liters) of fuel left in the
tank . Time to refuel
¢ page 216.
Ii Tank system malfunction! Contact dealer
If the indicator light turns on and this mes­
sage appears, there is a malfunction in the
tank system.
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
C> Windshield washer fluid level
II Please refill washer fluid
If the symbol illuminates, add windshield
washer fluid to the washer system/headlight
washer system* ¢
page 234.
~ Windshield wipers
rlJ Windshield wiper defective
There is a malfunction with the windshield
wipers.
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
~/0$ Defective light bulb warning
f'a-If the indicator light turns on, a bulb has
failed. The message indicates the location of
the bulb.
IJ-if a rear fog lamp has failed, the indicator
light turns on to indicate the location on the
vehicle.
Vehicle lights: malfunction
If the message appears, there is a malfunc ­
tion in the headlights or light switch .
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
A WARNING
- Light bulbs are pressurized and could ex­
plode while they are being changed caus­
ing serious personal injury.
- Work with due care when handling the
high-voltage section of gas discharge
(xenon) lights. Failure to do so could re­
sult in death or serious injury.

22 Instruments and warning/indicator lights
Have the bulb replaced or the connection
repaired by you r aut horized Aud i Service
department.
i,lD Headlight range control
II Headlight range control: defective !
If the symbo l illuminates, t he headlight range
contro l is no longer working properly . Have
the system checked and repaired at your Aud i
dealer .
l§O Adaptive Light
Applies to vehicles: with Adapt ive Light
II Audi adaptive light: system fault
If the indicator light t urns on and th is mes­
sage appears, there is a malfunction in the
adapt ive light system . The headlights still
f u nction .
Go to an aut hori zed dea lership to have the
h eadlights or the contro l unit for t he Adapt ive
Light repai red .
~D Light/rain sensor
f'al Automatic headlights /automatic wipers:
system fault
I f th e i ndicator lig ht turns on and t his mes­
sage appears, t he lig ht/ra in sensor is no t
f u nctioni ng cor rec tly .
For safety reasons the low beams are turned
on permanent ly w ith the switch in
AUTO .
However , you can continue to turn the ligh ts
on an d off using the light swi tc h. Y ou can still
con trol a ll fu nct ions tha t are indepe ndent of
t h e rai n sens or throug h the win dshi eld wipe r
l eve r.
Contact your au thor ized Audi deal er as soon
as poss ible to have the prob le m cor recte d.
¢ Q Turn signals
The indicator light blinks when you use either
turn signal .
Whenever yo u use the left B o r th e right rl
turn s ignal , the indicator light blinks. Whe n
you use the emergency flas he rs, both indica­
tor lights flash .
If one of the turn signa l light bulbs b urn o ut,
the turn signal w ill blink twice as fast as nor ­
mal. Carefu lly dr ive to your aut horized Aud i
dealer immed iate ly to have th e malfu nction
cor rected. The indicator lig ht does not indi­
cate a m alfu nction if a tur n signal on t he tra il­
er o r on the veh icle fails in trail er t ow ing
mode .
(D Tips
For m ore inf orm ation on the t urn sign als ,
r e fer to ¢
page 43 .
CRUISE/" (-) Cruise control
The warning/in dicator lig ht mIDJm (U SA mod ­
els)ll'II (Canada models) ill umi nates when
the cr uise c ontrol is activated ¢
page 76 .

Instrument s and warning /indicator lights 23
Driver information
display
Overview
Fi g. 4 Dr iver info rmat ion system i n th e inst rum ent
clus te r
Fi g. 5 Display: exa mple of th e informat ion line
The driver informa tion sys tem contains in for ­
mat ion
@ t h at is displayed on tabs@
c::> fig. 4. The following content is possible de­
pending on vehicle equipment:
@
Tab
1
2
3
®
Content
Vehicle functions :
On-board computer c>page 24
Efficiency program* c::> page 25
Digital speedometer
Cr uise control*
c::> page 76
Adaptive cruise control and Audi
braking guard *
c> page 78
Display darkened
Indicator lights and messages
Warning when a doo r, the hood or
t he rear lid is not closed
Service interva l display
c::> page 26
Speed wa rning sy stem c::> page 76
Night vision assistant * c> page 97
--~~-
@ ®
Tab Content
4 Audio/video
Telephone* Navigation*
The second and th ird tabs are only vis ible if at
least one indicator light or message is shown
or if that system is sw itched on .
The status line © is located in the bottom
part of the d isp lay
<=> fig. 4. It displays the ex­
terior temperat ure, time, selector lever posi­
tion, trip odometer and odometer .
For some vehicle f unctions , you can access t he
trip information from the temporary memory
c> page 24 in the line© c> fig. 5.
A WARNING
-
-Never re ly e xclusively on the o utside
temperature display to determ ine if a
road surface is icy or not. Keep in m ind
that road surface s, espec ia lly br idg es
a nd overpa sses, co uld be ice co ve red and
slippe ry even at a n o utside tempe rat ure
above 41 ° F (+ S °C).
- Always remember, even if the "snow­
f la ke" sym bo l (ice warning) does not ap ­
pear in t he dis play, black ice cou ld be on
the road.
- Always red uce your spee d an d drive with
special care in cold weathe r cond itions
when t he chance of enco untering icy
road surfaces increases.
(D Tips
- At tempe ra tu res below 14 ° F (+ 5 °C ) a
snowfla ke symbol a ppears ahead of the
temperat ure display . It is intended to re­
mind the driver to pay special attention
to
ice on the road c> .&. . If the vehicle is
stationa ry, or if you a re driving at a very
low speed, the temperature shown in the
display might be slightly higher than the
actual ou ts ide temperature. This is
c au sed by the heat bei ng r adia ted fro m
th e engine.

24 Instruments and warning /indicator lights
-You can se lect the un its used for temper ­
atu re, speed and other measurements in
the MMI.
- Fo r information on the a udio/video and
navigation * functions, refer to the se pa·
r ate MMI owner's manual.
Operation
The driver information system is operated us­
ing the buttons on the multifunction steering wheel.
Fig. 6 Mult ifunct io n steer ing whee l: ope rat ing t he d riv·
er informat io n system
Fig. 7 Driver informat ion syst em : open ing t he ve hicle
funct io ns m enu
Operating concept
> Switc h the ign ition on.
> To sw itch between the tabs, press the rock·
er switch
(D to the left or right¢ fig . 6.
> To acc ess additional informat io n be low or
above, rotat e the thumbw heel @down or
u p.
> To confi rm a se le ction, press the thumb­
whee l@ .
> Press the~ button @ to open a s ubmenu
for an active tab.
> Press the button © to access a function fo r
t h e p rogrammable stee ring wheel button* .
Accessing Vehicle functions
> Select the first t ab with the ro cker swi tch
(D .
> Press the button ~@. T he Vehicle func­
tions
menu appears ¢ fig. 7.
> To se lect a menu item, turn and press t he
thumbwheel @.
Resetting values to ze ro
> Select the on-board computer / Efficiency
program
menu item in the Vehicle func­
tions
menu .
> You can now select between the long-term
memory and s hort-term memory.
• To reset the values in a memory, p ress a nd
hold the thumbwheel @for one second .
Assigning a function to the
programmable steering wheel button*
• Select: !CAR ! function b utton> (Car) * sys·
tems
co ntrol b utton > Vehicle settings >
Program steering wh eel button .
The last fu nction selected d isp lays w hen you
switch the ig nition on.
On-board computer
You can ca ll up the fo llowing information in
the on-board computer:
- Da te
- Dr iv ing t ime (h) from the short-term memo-
ry
- Average consumption in MPG ( l/100 km)
from the short-te rm memory
- Average speed i n mph ( km/h) from the
s h ort-te rm memory
- Dis tance driven i n miles (km) from t he
s hort- te rm memory
- Current f uel cons umption in MPG ( l/100
km)
- Short-te rm memory overview
- Long-te rm memory overv iew
The short-term memory collects driv ing infor­
mation from the time the ign it ion is switched .,.

Instrument s and warning /indicator lights 25
on until it is switched off. If yo u continue driv ­
ing within two hours after switching the igni­
tion off, the new val ues are included when
calculating the current tr ip informat ion.
Unlike the short-term memory, the long-term
memory is not e rased automatica lly. You can
se lect the t ime period for eval uat ing trip in ­
formation yo urself.
F or some vehicle functions, you can access the
trip information from the temporary memory
i n the line
(I) ~ page 23, fig. 5.
Efficiency program
The eff iciency p rogram can help yo u to u se
l ess fuel. I t eva luates dr iving information in
re ference to fue l consumpt ion and shows oth ­
er equipment inf luencing co nsumption as we ll
as shift recommendations.
c> page 25. Fue l
economy messages
c> page 25 provide tips
for efficient driving. The eff ic iency prog ram
uses distance and consumption data from tr ip
computer
1.
To display the efficiency program, call up Ve ­
hicle functions and select the menu option
Efficiency program . If the data are deleted in
the efficiency program , those values are also
reset in trip computer.
(D Tips
- All stored va lues w ill be lost if the veh i­
cle battery is disconn ected.
- Fuel consumptions (ave rage and cu r­
ren t), range and spe ed are displayed in
m etr ic uni ts on Cana dian models .
Other equipment
Fig. 8 Tri p co mpute r: ot her eq uipment
Req uirement: The e fficiency program m ust be
displayed
~ page 25.
1-Tur n the thumbw heel u ntil th e other e quip-
men t ap pears in the display.
Ot her equ ipment t hat is c urrently affe cti ng
fuel consump tion is liste d in t he eff iciency
progr am. The disp lay sh ows up to th ree o ther
items of eq uipment @. The equ ipment using
the most fuel is listed first . If more than th ree
items us ing fuel are switched on, the equip ­
ment that is c urrently using the most fuel is
displayed .
A scale @also s hows the c urrent tota l co n­
sumption of all other equipment .
Fuel economy messages
Fig. 9 Dis play : exa m ple of a fuel eco nomy m essage
Fuel economy me ssage s are di splayed when
fuel consum ption is increased by cert ain con­
di tions. If you fo llow these fuel economy mes ­
sa ges, you ca n re duce your ve hicle's consump­
t ion o f fuel. The messages appear a utomat i­
ca lly and are only d isp layed in the efficiency
program. The fue l economy messages turn off
automat ica lly afte r a certain period of t ime .
.,. To turn an economy message off immedi-
ately after it appears, press any button on
the mult ifunct ion steering wheel.
{!) Tips
- Once yo u have tur ned a f ue l economy
m essage off, it will o nly appear agai n af­
ter yo u turn the ign itio n on again .
- The fue l economy messages are not dis­
played in every instance, but rather in in­
te rvals over a period of time.

26 Instruments and warning /indicator lights
Odometer
Fig . 10 In str ument cl uster: Odomete r an d reset but­
ton
The odometer shows yo u how many mile s
(kilome ters) yo u have driven. You c an switch
the disp lay from mi les to kilome ters and vice
ve rsa via the M MI.
Upper odometer
Th e trip odom eter shows the d istance d riven
si nce i t was last rese t.
It can be used to meas ­
u re shor t distances. The l ast d igit in di cates
1/1 0 of a m ile ( 100 mete rs) .
You can reset th e trip o dom eter to ze ro by
p re ss ing the Reset button~-
Lower odometer
The lower odometer shows the total numbe r
of m iles (k ilometers) d rive n.
Malfunction message
If t here is a ma lfunction in the instrument
cluster ,
DEF will appear in the trip odometer
d isplay area. Contact your authorized Audi
deale r to have the p roblem corrected.
Time and date display
F ig. 11 I n str ume nt cluster : cloc k an d date
You can set the time and t he date disp lay in
the MMI. Refer to the M MI owne r's manual
f or instructions.
When yo u open the driver's door, the date and
time appea r in the inst rument cluster disp lay
for 30 seconds .
Service interval display
The service interval display reminds you when
your next service is due.
Fig . 12 Instrume nt c lu ste r: Se rvice inte rval disp lay
The schedule for the next o il change or inspec­
tion is ca lculated automatically and disp layed
accord ingly . Th e d isp lay works in two stages:
Service reminder
30 days be fore the next service is d ue, a serv ­
ice reminder appears in the display when you
switch the ign ition on
¢ fig. 12.
After about 5 seconds the display switches
back to norma l. The distance and time re­
mai ning are updated each t ime the ignit io n is
switched on until the date due for service is
r eached.
Service due
When the due date for se rvice is reached, the
message
Service due! appears in the instru­
ment cluster immed iate ly after yo u sw itch the
ignition o n. Add it iona lly, a warning tone
sounds . After about 5 seconds the disp lay
switches bac k to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI display by selecting
t h e service interval d isplay in the car menu.
II>

Instrument s and warning /indicator lights 2 7
Select the I CAR I func tion button > Car sy s­
tems
co ntrol button > Servicing & check s >
Service inte rval displays . In new vehicles, the
schedu le can only be called up after approx i­
mate ly S00 km.
Resetting the ser vice interval d isplay
Your authorized A udi dealer wi ll rese t the cor ­
respo nding service schedule after performing
the appropriate service on yo ur vehicle. You
also have the possibility to reset the oil
change schedule after having performed an
oil change accord ing to Audi specifications.
Select the
I CAR ! function b utton > Car sys­
tem s
control button > Servicing & checks >
Servic e int erval display s> Reset oil change
interval.
(D Note
If you disconnect the bat tery t ermina ls, no
calc ulatio ns can be made for the servi ce
interv al displ ay d uring this time and no
service remi nder w ill appear. Remembe r
that obse rving the prope r se rv ice intervals
is vita lly impo rtant to extend ing the life of
y o ur veh icle, part icu larly the eng ine, and
maintaining its va lue . Even if th e mileage
driven is low, the maximum period of one
yea r from one se rvice to the next must not
be excee ded.
@ Tips
- Do not reset t he display between o il
changes, o therw ise the display will be i n­
cor re ct.
- The informati on in the Service Reminder
r ema ins sto red even when the vehicle
batte ry is disco nnecte d.
Head-up Display
Applies to vehicles: with Head-up Disp lay
Fi g. 13 Exampl e: indica tors in th e Head -up D isp lay
Fi g. 14 In strument pa nel: k nob for the Head-up Dis­
play
T he Head- up D isplay projects certain warnings
o r se le cted information from the ass istance
systems* o r naviga tion * on t he windshie ld.
T he disp lay appea rs within t he dr ive r's fie ld o f
vision .
Switching on/off
1-Press t he knob~ to switch the Head-up
Displ ay on/off ¢
fig. 1 4.
Adjusting the height
The height of the dis p lay can be adjusted to
the individual drive r.
.. Make s ure you are seated correctly
¢page
124 .
.. Turn the knob~ to adjust the display.
Settings in the MMI
.. Se lect: I CAR I function button > Car systems
cont ro l butto n > Driver assistance > Head·
up D isplay
> Head -up Display content or
Display br ightness . ..,.

28 Instruments and warning /indicator lights
Display content
In the MMI, you c an specify which informa tion
shoul d be displayed :
- Cru ise cont ro l system*
- Nav igat ion information *
- Audi adaptive cruise control*
- Night vision assistant* (pedestrian warning)
The speed display and some of the red indica­
tor lights cannot be hidden in the MMI.
Display brightness
You can adjust the display b rightness in t he
M MI. The display bright ness decreases auto­
mat ic all y as the amo unt of light decreases.
The basic leve l of bright ness is adjusted with
the instrument illumination ¢
page 44.
(D Note
To preve nt scratches on the g lass coverin g
the Head -up Display, do not place any ob ­
jects i n the projection opening.
(D} Tips
- S ung lasses w ith pol ariza tion filters an d
u nfavorable ligh ting co ndi tions can af ­
fect the display.
- Vehicles wi th sea t memory *: yo ur Hea d­
up D isplay setting s are stored automati­
ca lly and assigne d to the remote cont ro l
key that you are using .
- A specia l w indshield is needed for the
Head-up Display funct io n.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction In dicator Lamp (MIL) I! in
the instrument cluster is part of the On-Board
Diagnostic (OBD II) system.
The warning/indicator light illumina tes when
the ign ition is switc hed o n and goes o ut afte r
the engine starts and the idle has stab ilized .
This indicates that the MIL is working proper­
ly .
If the light does not go out after t he e ngine
is started, or illuminates wh ile you are dr iv­
i ng, a mal funct ion may exist in the eng ine sys ­
tem . If the light illuminates, t he catalytic con­
verter could be damaged .
Contin ue driving
with reduced power (avo id­
i ng s ustained high speeds and/o r rap id accel ­
erations) and have the cond ition corrected.
Co ntact your a uthorized Audi dea ler.
If the light i llum inates, the e lectronic speed
li miter may also be mal funct ion ing. Fo r more
information ¢
page 29, Electronic speed
limiter.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
¢ page 217.
On-Board Diagnostics
Fig. 15 Locat io n of Data Li nk Co nnector (D LC)
On- Boa rd Di agnost ics monitors the compo ­
nents of your emissio n contro l system . Each
monitored component in your engine system
has been ass igned a code. In case of a mal­
funct ion, the component will be identified
and t he fault stored as a code in the control
modul e memo ry.
The MIL light may also illuminate if there is a leak in the on-board fuel vapor recovery sys·
tem. If the light illumi nates afte r a refu elling,
stop the vehicle a nd make sure the fuel fille r
cap is prope rly closed ¢
page 217.
In order to make a n accurate diagnosis, the
stored data can o nly be displayed using spe­
c ial d iagnost ic equipment (generic scan tool
fu rOBD) .
~