wheel AUDI A6 2013 Owners Manual

266 What do I do n ow ?
-Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury .
@ Tips
-Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bo lts.
- If a whee l bolt is very tight, you may find
it easier to loosen by carefully pushing
down on the end of the wheel bolt
wrench w ith
one foot only. As you do so,
hold on to the car to keep your balance
and take care not to slip .
Raising the vehicle
The vehicle must be li~ed with the jack first
before the wheel can be removed .
Fig. 20 5 Sill pa nels : m ark ings
~
9
---;~ :~-;;:--~
Fi g. 20 6 Sill: pos ition ing the ve hicle jack
.,. Activate the vehicle jack mode* in the MMI :
I CAR! func tion button > (C ar)* sy ste m s con ­
t ro l butto n
> Servici ng & che ck s> Air su sp. :
j a ck mode > On .
.,. Engage the parking br ake to prevent your
vehicle from ro lling unintentionally.
.,. Move the
sel ector le ve r to po sit ion P .
.,. Find the marking (imprint) on the sill that
is nearest the wheel that wi ll be changed
¢
fig. 205. Be hind the marking, there is a
lift ing point on the sill for the vehicle jack .
.,. Vehicles with a sill: remove the cover from
the sill before lift ing the veh icle w ith a vehi ­
cle jack ¢
page 267.
.,. Turn the vehicl e jack located under the lift­
ing point on the sill to ra ise the jack u nti l its
arm @¢
fig. 206 is located under the des­
ignated p lastic mount ¢_&. ¢(!).
.,. Align the jack so that its arm@¢
fig. 206
engages in the designated lifting point in
the door si ll and the movable base @ lies
flat on the ground. The base ® must be
ver­
t ical
under the lifting point @ .
.,. Wind the jack up fu rther until the f lat t ire
comes off the ground ¢
,&..
Position t he veh icle jack onl y under the desig­
nated lifting points on the s ill ¢
fig . 205.
T here is exactly one locat ion for each wheel.
T he jack must not be positioned at any other
location ¢ _& ¢(j) .
An
un stab le surfa ce under the jack can cause
the vehicle to slip off the jack . Always provide
a firm base for the jack on the ground .
If nec­
essary place a sturdy board or sim ilar support
u nder the jack. On
h ard , s lipp ery surf aces
(such as tiles) use a rubber mat or similar to
preve nt the jack from slipping ¢
.&..
A WARNING
--You or your passengers co uld be injured
while changing a wheel if you do not fo l­
low these safety precautions:
- Position the vehicle jack on ly at the
designated lifting poi nts and align the
jac k. Otherw ise, the vehicle ja ck could
slip and cause an injury if it does not
have sufficient hold on the vehicle.
- A soft or uns table su rface under the
j ack may cause the vehicle to slip off
the jack . Always provide a firm base for
the jack on the ground. If necessary,
use a sturdy board under the jack. ,...

-On hard, slippery surface (such as tiles)
use a rubbe r mat or similar to prevent
the jack from slipping .
- To he lp prevent injury to yourself and
your passengers:
- Do not raise the vehicle until yo u are
sure the jack is secu rely engaged.
- Passengers must not remain in the ve­
h icle when it is jac ked up.
- Make sure that passengers wa it in a
safe p lace away from the vehicle and
well away from the road and t raffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to
r ai se the jack.
- Changes in temperatur e or load can af­
fect the height of the ve hicl e.
(D Note
Do not lift the ve hicle by the s ill. Position
the vehicle jack only at the des ignated
lift­
ing points on the sill. Othe rwis e, your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode* switches off auto­
mat ica lly at speeds above 6 mph (10 km/
h).
Removing and installing the sill cover
Applies to vehicles : wit h sill
Fig. 207 Sill: remov ing t he cover
.,. Pull the cover down to remove it c::> fig . 207.
.,. To install the cover again, inse rt it into the
retainers and then sw ing it upward unt il it
cl icks into place . T he cover m ust be flush
with the sill.
What do I d o now ? 267
@ Tips
Some models may also have a cover for the
rear vehicle lift po int.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing th e wheel.
Fi g. 208 Cha ngi ng a w heel: us ing th e screwd rive r ha n­
d le (w it h th e blade re m oved) to turn the bo lts
F ig . 209 Chang ing a whee l: a lig nment p in in sid e the
top hole
After you have loosened all wheel bo lts and
raised the vehicle
off the ground, remove and
replace the wheel as follows :
Removing th e wheel
.,. Use the hexagonal socket in the screwd riv ­
er handle
to complete ly remove the top­
most wheel bolt and set it aside on a
clean
surface c::> fig. 208 .
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-t ight into the
empty bolt hol e
c::> fig. 209 .
.,. Then remove the other wheel bolts as de­
scribed above .
.,. Take
off the whee l leaving the alignment
pi n in the bolt hole
c::> (l).

268 What do I do no w?
P uttin g on the spare wheel
.. Lift the spare wheel and ca refully slide it
over the alignment pin to guide it in place
¢ (D .
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.. Remove the alignment pin and insert and
t ighten the remaining wheel bolt slightly
L ike the rest .
.. Turn the jack handle cou nter -clockw ise to
lower the vehicle unt il the jac k is fully re­
leased.
.. Use the wheel bolt wrench to tighten all
wheel bolts firmly¢
page 265 . Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you .
(j) Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or t ighten
the wheel bolts .
- Pull the reversible blade from the screw­
driver before you use the hexagonal
socket in the handle to turn the wheel bo lts.
- When mounting tires with
unid irectional
tread design
make sure the tread pat­
tern is pointed the right way
¢ page 268.
-The wheel bolts should be clean and easy
to tu rn . Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the h ub. Remove al l dirt from these
surfaces before remo unting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a sp are t ire w ith a tre ad pattern
intended for use in a specific direction
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection , please
note the following :
- The direct ion of rotation is marked by an ar­
row on the side of the tire .
- If the spare tire has to be installed in the in­
correct direct ion, use the spare tire only
temporarily s ince the tire will not be able to
achieve its optimum performance cha racter­
isti cs wit h regard to aquap lan ing, no ise and
wear .
- We recommend that you pay part icu la r at­
t ention to th is fact d uring wet wea ther and
t ha t you adjust you r speed to match road
conditions .
- Replace the fl at tir e with a new one and
have it insta lled on you r vehicle as soon as
possible to restore the handling advantages
of a u nidirectional tire .
Notes on wheel changing
Please read the information¢ page 251, New
tires and replacing tires and wheels
if you a re
going to use a spare tire which is different
from the ti res on your vehicle .
After you change a tire:
- Check the tire pre ssure on the spar e imm e­
diately after install ation.
- Have th e whe el bolt tight ening torqu e
c hecked with a torque wrench as soon a s
pos sible by your author ized Audi de aler or
a q ualified service stat ion.
- With steel and allo y wheel r im s, the wheel
bolt s ar e cor re ctl y tightened at a torque of
90 ft lb (1 20 Nm ).
- If you noti ce th at the wheel bolts are cor­
roded and diffi cult to turn while changing
a ti re , they should be repl aced before you
check the t ightening torque. .,..

-Replace the flat tire with a new one and
have it installed on your vehicle a s soon as
possible. Remount the wheel co ve r.
U ntil th en, driv e with extr a car e and at re ­
du ced speeds .
~ WARNING
-
-If you are going to equip your vehicle
with t ires or rims wh ich differ from those
wh ich were factory installed, then be
sure to read the informat ion
c:> page 251,
New tires and replacing tires and
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool k it
are properly secured in th e luggage com·
partment and are not loose in the pas·
senger compartment.
- In an accident o r sudden maneuver they
c ou ld fly forward, inju ring anyone in the
vehicle .
- Always store damaged w heel, jac k and
tools secure ly in the luggage compart­
ment. Otherw ise, in an acc iden t or sud­
den maneuver they cou ld fly forward,
causing injury to passenge rs i n the vehi·
cle .
What do I do now? 269
•
•

280 General information
General information
Explanation of
technical data
Some of the technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
r:::> page 282. This sec­
tion provides general information, notes and restrictions which apply to this data.
Vehicle identification
The key data is given on the vehicle identifica­
tion number (VIN) plate and the vehicle data
sticker .
Fig. 223 Veh icle Ide ntificat io n Number (VlN) p late: lo ­
cation on driver 's s ide das h panel
Fig. 224 The vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
ble from the outside through the windshield
r:::> fig . 223. You can also display the Vehicle
Identification Number of your vehicle in the
MMI. Select: Function button
I CAR ! > (Car) *
systems
> VIN number . The
vehicle identification label
is located in the luggage compartment in the
spare wheel well.
The label¢
fig. 224 shows the follow ing vehi­
cle data :
(D Product ion control No .
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo-
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War­
ranty
& Maintenance booklet.
The safety compliance sticker
is your assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
t ime the vehicle was manufactured . You can
find this sticker on the left door jamb .
It
shows the month and year of production and
the vehicle ident ification number of yo ur vehi ­
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carrier.
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the bas ic vehicle plus fu ll fuel tank,
oi l and coo lant, plus maximum load, which in­
cludes passenger weight (150 lbs/68 kg per
Ill>

Data
A6 310 hp, 3.0 liter 6-cylinder engine
Applies to vehicles: with 3.0 liter 6-cylinder engine and all-wheel drive
Engine data
Maximum output SAE ne t
Maximum torque SAE net
No. of cylinders
Displacement
Stroke
Bore
C ompression ratio
Fuel
Dimensions (approx .)
L eng th (wit h license pl ate brac ket)
Width (across mirrors) He igh t (unloaded)
310@ 5500-6500 hp@ rpm
lb-ft@ rpm
-.. .--
C ID (cm3
)
in (mm)
in (mm)
__ ,
-~-- ,
325 @ 290 0-4500
6
182 (2995)
3.50 (89.0)
3 .33 (84.5)
10.3: 1
Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance. Further details¢
page 220,
Gasoline
in (mm) 193.9 ( 4925)
in (mm) 82.1 (2086)
in (mm) 57 .8 ( 1468)
Turning circle diameter (curb to curb) ft. (m) 39.0 (11.9)
Capacities (appro x.)
Fuel tank
- Total capac ity
- Reserve (o f to tal capacity)
Windshield fluid container
Windshield and headlight washer
fluid container *
Engine oil with filter change gal (liters)
19.8 (75.0)
gal (li
ters) 2. 6 (10.0)
quarts (liters) 3.7 (3.5)
qu arts ( liters) 5 .2 ( 4.9)
quarts (lite rs) 7.2 (6.8)
283
•
•

284 Data
S6 420 hp, 4.0 Liter a-cylinder engine
Applies to vehicles: with 4.0 liter 8-cylinder engine and all-wheel d rive
Engine data
Maximum outpu t SAE ne t
Maximum torque SAE net
No. of cylinders
Stroke
Bore
Compressio n ratio
Fuel
Dimensions ( approx .)
Leng th (with lice nse pl ate bra cket)
Width (across mirrors) He igh t (unloaded) hp@ rpm
lb-ft@ rpm
CID (cm
3 )
in (mm)
in (mm)
__ ,
-~ .. ,
420 @ 5500-6400
406@ 140 0-5200
8
24 3 .67 (3993)
3 .50 (89 .0)
3 .33 (84.5)
10 .1: 1
Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance . Further details¢
page 220,
Gasoline
in (mm) 193 .9 (4 925)
in (mm) 82.1 (2086)
in (mm) 57 .8 ( 1468)
Turning circle diamet er (curb to curb) ft. (m) 39 .0 (11.9)
Capacities (appro x.)
Fuel tank
- Total capacity
-Reserve (o f to tal capacity)
Windshield fluid container
Windshield and headlight wa sher
fluid container *
Engine oil
with filter c hange gal (li
ters)
19 .8 (75 .0)
gal (li ters) 2. 6 (10. 0)
q uarts (lit ers) 3 .7 (3 .5)
qu arts ( li1ters) 5 .2 ( 4.9)
quarts (li te rs) 8 .8 (8.3)

28 6 Con sum er Inf ormation
comp lexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, s afety an d e nvir onm ent al con­
cerns place very strict limits on the nature of repairs and adjustments to engine and trans ­
miss ion pa rts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure proper
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­ ranty. Therefo re , proof of servici ng in accord­
ance w it h the ma intenance sched ule may be a
condition for upholding a possible warranty
claim made within the warran ty period.
Above all, operational safety can be adve rsely
affected, creating unnecessary risks for you
and your passengers.
If in doubt about any serv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop .
We strong ly urge you to give your authorized
Audi dealer the opportunity to perform all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and tra ined spec ialists to keep your vehicle
running properly .
Performing lim it e d m aint en anc e y ourself
The fo llowing pages describe a limited num­
ber of procedures which can be performed on
you r vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and ca refully follow the instruc­
tions given. Always rigorously obse rve the
WARNINGS p rovided .
Before you ch eck anything in th e engin e
compartme nt, alway s read an d heed all WARNINGS
¢ & a
nd ¢ & in Working in the
engine comportment on page 225 .
A WARNING
--Serious personal in jury may occur as a re-
sult of improperly performed mainte­ nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r isk personal
in jur y.
- Do not attempt any of the maintenance,
checks or repairs descr ibed o n the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re­ spect to the vehi cle, or are uncerta in how
to proceed .
- Do not do any work withou t the proper
too ls and equipment . Have the necessary
work done by your authorized A udi deal ­
er or anothe r properly equipped and
qualified workshop.
- The engine compar tment o f any motor
vehicle is a potentially hazardous area. Never reach into the area around or
touch the rad iator fan. It is temperature
control led and can sw itch on suddenly -
even when the engine is off . The radiator
fan switches on automatically when the
coo lant reaches a ce rtain temperature
and will cont inue to ru n until the coo lant
tempera ture drops.
- Always sw itch off the ignition before any­
one gets under the vehicle.
- Always support your veh icle with safety
s tands if it is necessary to work under­
neath the vehicle. The j ack s upp lied with
the vehicle is not adequate for this pur­
pose and cou ld co llapse causing serio us
pe rsonal injury .
- If you must work underneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on leve l ground,
that the wheels are a lways secure ly
blocked and that t he engine cannot be
started .

29 0 Index
A
Accessories . ...... ..... ... .. .. .... . 28 7
Active lane ass ist . . . . . . . . . . . . . . . . . . . . 91
Activating and deactivating . . . . . . . . . . . 92
C leaning came ra area ... .. .. .. .. .. . 211
Descr ipt ion ... ........... .. .. .... .. 9 1
I nstrument cluster indicator light . . . . . 92
Messages . . . . . . . . . . . . . . . . . . . . . . . . . 92
Notes on instrument cluster display . . . . 92
Setting the steering wheel vibrat ion . . . . 93
AC (automatic cl imate control) . .. .. .. .. 67
AC (climate control) . . . . . . . . . . . . . . . . . . 65
Adaptive air suspension/sport . ... .. .. . . 98
Adapt ive cruise control . . . . . . . . . . . . . . . . 82
C leaning sensors/cameras .. .. .. .... . 211
Messages ............... .. .. .. .. .. 89
Request for driver intervention . . . . . . . . 8 7
Stop-and-go traffic . . . . . . . . . . . . . . . . . 86
Adapt ive Lig ht (defective) ... .. .. .... .. 22
Adding Eng ine coolant ............. .. .... . 233
Eng ine oil .. ..... ........... ... .. . 230
W indshield washer fluid .. ... .. .. .. . 239
Additives Eng ine oil ............... .. .. .. .. . 230
Ad justing
Air distribution (automatic climate con-
trol) ..... .. ... .. ..... ... .. .. .... .. 68
air distribution (climate control) . .... .. 65
Front seats . . . . . . . . . . . . . . . . . . . . . . . . 50
Instrument illum inat ion ... .. .. .. .. . .
44
Steer ing column electrically .. .. .. .. . . 70
Steer ing column manually ..... .. .... 70
Tempe ratu re (automat ic climate control) 68
Tempe ratu re (climate control) .. .. .. . . 65
A irbag system . . . . . . . . . . . . . . . . . 145, 166
Advanced Airbag System . . . . . . . . . . . . 149
Advanced Airbag System components . 153
Care ....... .......... ...... ... .. . 161
C hi ldren . ............... .. .. .... . 173
C hi ld restra ints ........... .. .. .. .. . 173
Components (front airbags) . .... ... . 153
Danger of fitting a child seat on the front
passenger seat . . . . . . . . . . . . . . . . . . . . 147
Disposa l ..... ........... .. .. .... . 161
Front airbags . . . . . . . . . . . . . . . . 149, 151
H ow do the front airbags work? . .... . 155 How many a
irbags does my vehicle
have? . ... .... .. .. ... .. ..... ... .. 153
How the Advanced Airbag System com -
ponents work together ......... .... 155
Important safety instructions on the
knee airbag system ................ 164
Important things to know . .. .. .. .. .. 145
Knee airbags . .. .. .......... ...... . 162
Monito ring .. .. . .. ............ .. .. 15 7
PASS ENG ER A IR BAG OFF light ... .. .. 158
Repairs ... .... .. .. ... .. . .... ... .. 161
Safety instr uctions . .. .. ..... .... . .. 160
Side airbags ..... .. ... ..... ... .. .. 165
S ide curtain airbags ............ .... 168
Warning/ind icator lights ........ .... . 19
Warning/Indicator lights ....... .... 157
When must the system be inspected? 157
Aircraft Transporting your vehicle ..... .. .. .. 278
All-wheel drive .. .. ............. .... 196
Win ter tires . .. . .. ............ .. .. 255
Alloy wheels .. .. .. .......... ...... . 213
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Amb ience lighting ................ ... 44
Anti-freeze
refer to Eng ine coolant ............ . 232
Anti- lock braking system . ..... ... .. .. 192
Warning/ind icator lights ........ .... . 20
An ti-s lip reg ulation ............. .. .. 192
Anti-theft systems Electronic immob ilizer ............. .. 32
Ashtray . ... .... .. .. ... .. ..... ... .. . 56
Audi braking guard
refer to b rak ing guard .......... .... . 82
Audi drive select
refer to drive select ............... .. 98
Audi Serv ice Repair Manuals and Litera-
ture ... .... .... .. ............. .... 285
A UTO
a ut omatic climate contro l . . . . . . . . . . . . 68
Automatic headlights ... .... ... .. .. . 41
climate control ... .. ... ..... ... .. .. . 65
A uto Lock .. .... ... ................ . 33
Automat ic be lt retractor ........... .. 139
A utomatic car wash . .... ..... ... .. .. 209

Automatic climate control Air vents ... ..... ..... ... .. .. .. .... 68
Automatic recirculation . . . . . . . . . . . . . . 69
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 67
Setup ... .. ................. .. .... 69
synchron izing ............... ... ... . 68
Automatic Shift Lock (ASL) . ... .. .. .. . 106
Automatic t ransmission
Automatic Sh ift Lock (ASL) . .. .. .. .. . 106
D nvrng .. .. ............. .. .. .. .. . 10 7
Emergency mode . ..... ... .. .. .. .. . 110
Emergency release . . . . . . . . . . . . . . . . . 1 11
Kick-dow n .. .. .... .... ... .. .. .. ... 110
Manual shift program ..... .. .. .. .. . 109
multitronic ® . . . . . . . . . . . . . . . . . . . . . . 105
Selector lever . . . . . . . . . . . . . . . . . . . . . 105
S tron ic ® ...... ........... ... ... .. 105
tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . 105
Automatic wipers .......... .... .. .... 46
Auto Safety Hotline ........ .. .. .. .. . 134
Average consumption ............ .... . 24
Average speed . . . . . . . . . . . . . . . . . . . . . . . 24
Avoid damaging the vehicle .. .. .. .. .. . 200
B
Battery ... ... ............. ...... .. 235
C ha rging ................... ... ... 237
I mportan t war nings ...... .. .. .. .. . 236
Ju mp s tarting . ........... .. .. .. ... 274
L ocat ion ... ... .. ..... ... .. .. .. ... 236
l ow ..... .. .. .. ... . .... ... .. .. ... 197
Replacing the battery .. ... .. .. .. .. . 239
State of charge ........... .. .. .. ... 197
W inter operation ......... .. .. .. .. . 235
Working on the battery .... .. .. .. .. . 236
B efore driving . ... .. .... ... .. .. .. ... 126
B lended gasoline . ............. ... .. 220
Blower (automatic climate control) . . . . . . 68
B lower ( climate con trol) . . . . . . . . . . . . . . . 65
Body cav ity sealing .......... ... ... .. 214
Booster seats . .. .. ..... ... .. .. .. ... 180
B rake fl uid
Changing the brake fl uid ... .. .. .. .. . 235
C heck ing the bra ke fluid level . .. .. .. . 234
What is the cor rect brake fl uid leve l? .. 234
What should I do if the bra ke fl uid warn-
ing light comes on? ....... .. .. .. .. . 234
Inde x 291
Brake system
Anti- lock b raking system ..... ... .. .. . 20
B rake assist system .. .. ..... ... .. .. 192
Brake booster .. .. ................. 195
Brake fluid .. .. .. .... ............. 234
B rake fluid specifications fo r refill and re -
placeme nt .. .. .. .. . .. .... .... .. .. 235
B ra ke light defective . . . . . . . . . . . . . . . . 22
Br ake pads . . . . . . . . . . . . . . . . . . . . . . . 199
El ec tromech an ic al par king br ake . .. .. . 74
Fl uid reservo ir ... .. .. .. ...... ... .. 23 4
How does moist ure or roa d salt affect the
brakes? ... .. .. .... . ... ...... ... .. 194
Warning/ind icator lights ........ .... . 15
Worn brake pads symbol . . . . . . . . . . . . . 20
braking gu ard
Set tings . ... .. .... . ... ...... ... .. . 89
B rak ing guard ..... .. ................ 82
Messages . .. .. .. .... ........... .. . 89
Break-in per iod .. .. .. ............... 199
B rake pads .. .. .. .... ... .... .... .. 199
T ires ........ ... .. ..... .......... 199
Bu lbs . ... .. .. .... .. . .. .. ..... ... .. 273
C
Cali forn ia Proposition 65 Warn ing ... .. 226
Battery specific .... . .. ..... ... .. .. 237
Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 282
E ngine o il . .. .. .. ................. 227
Car care .... .. .. .. ................. 208
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Inter ior ... .. .. .. .. . .. .... .... .. .. 214
Car carrier Transporting your vehicle ....... .. .. 278
Cargo area . ... .... .. . .. ... .... ... .. 132
Cargo ne t . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Catalytic converter ... . ... .... ... .. .. 200
Center armre st
Cockpit ... .. .. .. ................. . 52
Central lock ing .. .... ... ....... ...... 33
E mergency locking .. ... ....... .... .. 37
Certification . . . . . . . . . . . . . . . . . . . . . . . 288
Ch ang ing a wheel .. .... ......... .... 263
Changi ng engine oil .. ... ....... .... . 231
Chassis (undercoating) . . . . . . . . . . . . . . . 214
•
•