tow AUDI A7 2013 Service Manual

Catalytic converter
It is very important that your emission con­trol system (catalytic converter) is function­
ing properly to ensure that your vehicle is run­
ning in an environmentally sound manner .
.. Always use lead-free gasoline¢ page 225,
Fuel supply.
.,. Never run the tank down all the way to
empty.
.,. Never put too much motor oil in your en-
gine
¢ page 235, Adding engine oil~-
.,. Never try to push- or tow-start your veh icle.
The catalytic converter is an eff icient "clean­
up" device built into the exhaust system of
the vehicle . The catalytic converter burns
many of the pollutants in the exhaust gas be ­
fore they are released into the atmosphere.
The exclusive use of unleaded fuel is critically
importa nt for the life of the cata lytic convert­
e r and proper functioning of the engine.
A WARNING
-
- Do not park or operate the vehicle in
areas where the hot exhaust system may
come in contact with dry grass, brush,
fuel spill or other material which can cause a fire.
- Do not apply additional undercoating or
rustproofing on or near the exhaust
man ifold, exhaust pipes, catalytic con­
verter or heat shields. During driving, the
substance used for undercoating cou ld
overheat and cause a fire.
0 Note
- Be aware that just one tank filling with
leaded fuel will already seriously de­
grade the performance of the catalytic
converter.
- Do not exceed the correct engine oil level
¢ page 235.
-Do not drive until the fuel tank becomes
completely empty. The eng ine could mis­
fire . U nburned fuel could a lso get i nto
Dri vin g and en vironm ent 205
the exhaust system and this cou ld cause
the catalytic converter to overheat .
- Do not switch off the ignit ion while the
vehicle is mov ing.
- Do not continue to ope rate your veh icle
unde r these conditions, as othe rwise fuel
can reach the catalytic converter. This
co uld result in overheating of the con­
verter, requir ing its replacement .
- To assure efficient operation of the Emis ­
sion Control System:
- H ave your vehicle maintained prope rly
and in accordance w ith the se rv ice rec­
ommendat ions in you r Warranty &
M aintenance boo klet.
- L ack of prope r maintenance as we ll as
improper use of the vehi cle w il l impair
the function of the em ission contro l
system and could lead to damage .
@ For the sake of the environment
Even when the Emiss ion Control System is
operat ing properly, the exha ust gas can
have a sul fur -li ke exhaust gas smell under
some operating states . This depends on
the sulfur content of the fuel being used .
Using a different brand of fue l may help,
or filling the tank with lead-free super
grade gasoline .
Avoid damaging the
vehicle
When you are drivi ng on poo r roads, or over
c ur bs, s teep ramps, etc., ma ke certai n that
low -lying parts s uch as spoilers and exhaust
system pa rts do not bottom o ut and get dam­
aged.
T h is is espec ially true for veh icles w ith low­
s lung chassis (spor ts chassis)* and fully load­
ed vehicles. •
•

Trailer towing Driving with a trailer
General information
Your Audi was designed primarily for passen­
ger transportation .
If you plan to tow a tra iler, p lease remember
that the addit ional load will affect durab ility,
economy and performance .
Trailer towing not on ly places more stress on
the vehicle, it also calls for more concentra­
tion from the driver.
F or this reason, a lways fo llow the operating
and driving instructions provided and use
common sense.
(D Note
If you are going to tow a trai ler, you must
ac tivate the trailer operation mode
c::> page 209, Operating instructions.
Technical requirements
Traile r hitch
Use a weig ht-carrying hitch conforming to the
gross trailer we ight. The hitch must be suita­
b le for your veh icle and trailer and must be
mounted securely on t he ve hicle's chassis at a
technically sound location . Use only a trail er
hi tch w ith a removab le ball moun t. A lways
check wi th t he tra ile r hi tch man ufa ctur er to
make sure that you are using the cor rect
h itch.
Do not us e a bumper hitch .
The hitch m ust be installed in such a way that
i t does not interfe re with the impac t-absorb­
i ng bumper syst em. No mod ificat ions should
b e made to the vehi cle e xhaus t and br ake sys­
tems . From t ime to time, check th at a ll hitc h
mo unt ing bo lts rem ain securely fas tened.
When you are not towing a trail er, remove the
tra ile r hi tch ball moun t. T h is prevents the
hi tch from causing damage sho uld your ve hi­
cle be str uck from behind~ .&.
Trailer towin g 209
Trailer brakes
If your trailer is equippe d wi th a bra king sys­
tem, check to be s ure that i t conforms to all
regulations .
T he trailer hyd ra u lic bra ke sys tem mus t not be
d irec tly connec ted to the vehicle's hydraulic
brake system .
Safety chains
Always use safety chains be tween your ve hicle
and t he tra ile r.
Trailer lights
Trai ler lights must meet all reg ulations. Be
su re to c heck with your Audi dea ler for correct
wir ing, switches and relays .
Mirrors
If you a re unable to see the traffic behind you
u sing the regula r outside mirrors, then you
must insta ll extended mir rors. It is important
t h at you
always have clea r vis io n to the rear.
_&. WARNING
-
Afte r removi ng the trailer hitch , do no t
s tor e i t in yo ur v ehicl e. In case of sudden
b raki ng, the hi tch co uld fly forwar d and in­
j ur e you o r yo ur pass enge rs.
Operating instructions
Maximum trailer weight
A tra ile r fo r you r vehi cle is l imited to a typi cal
cla ss 1 o r class 2 tr ailer.
Trailer load distribution
Be sure the load in the tra ile r is held secure ly
in place to p revent it from shift ing fo rward,
ba ckward or sideways.
Never allow a passenger to ride in a trailer
c::> .& in Driving instructions on page 211 .
Engine cooling sy stem
Towing a t railer ma kes the engine wor k hard­
er . It is impo rtant that the cooling system's
performance is up to the additional load.
•
•

210 Trailer towing
Make sure that the cooling system has eno ugh
fluid .
Tire p res sure
When tow ing a trai le r, inflate the t ires of your
vehi cle to the co ld tire pressure listed under
"Full load" on the label located on the driver's
side B-pillar (visible when the door is open) .
Inflate trailer t ires to trai ler and tire manufac­
turers' specifications.
Lights
Chec k to make s ure both veh icle and trailer
lights are working properly.
Safety chains
Be sure tra iler safety cha ins are properly con­
nected from the trailer to the hitch on the ve­
h icle. Leave enough slack in the chains to per ­
mit turn ing corners . When you install safety
cha ins, make su re they wi ll not drag on the
road when yo u are driving.
The chains shou ld cross under the tra iler
tongue to prevent it from dropping in case of
separation from the hitch.
Adjusting the Audi drive select
Make sure the vehicle is on a level su rface be­
for e
hitching up the tra ile r and b efor e adjust­
ing the tongue weight. The vehicle must be in
auto or comfort dr iving mode and no t raised
qpage 102, q(D _
Make sure that the vehicle is lowered. In Info­
tainment , se lect:
ICARI f u nction button> Low­
e r
control b utton .
I f you m ust dr ive under poor road co ndit ions,
you can raise the veh icle
aft er coup ling the
tra iler or
after adjusting the tong ue weig ht
q page 104.
-Changes in tempe ratu re or load can af­
fect the heig ht of the veh icle.
- Always se lect
auto or comfort mode.
Otherwise, the tongue load spec ified for
your vehicle will no longer be applicable.
Driving instructions
Driving with a trailer always requires extra
care and consideration .
To obtain the best possible handling of vehicle
and trailer, please note the fo llow ing:
.,. Do not tow a loaded trailer when your car it­
self is not loaded.
.,. Be especially carefu l when passing other
veh icles.
.,. Observe speed lim its .
.,. Do not dr ive at the maximum permissible
speed.
.,. Always app ly brakes early .
.,. Monitor the temperatu re ga uge.
Weight distribut ion
T owing a loaded trailer with an empty car re­
su lts in a highly unstab le distribution of
we ight. If this cannot be avoided, drive at very
low speeds on ly to avoid t he risk of losing
steering con trol.
A "ba lanced " rig is easier to operate and con­
tro l. This means that the tow vehicle should
be loaded to the exten t possible and permissi­
ble, while keep ing the trai ler as light as possi­
ble under the c ircumstances . Whenever poss i­
ble, transfer some cargo to the luggage com ­
partment of the tow veh icle while observing
tong ue load requirements and vehicle load ing
considerations.
Speed
The higher the speed, the more difficu lt it be ­
comes for the driver to control the rig . Do not
drive at the maximum permissible speed. Re­
duce your speed even more if load, weather or
wind conditions are unfavorable -particularly
whe n going downhill.
Red uce veh icle speed
immediately if the trail­
er shows the slightest s ign of sway ing .
Do not
try to stop the swa ying b y accelerating .
Observe speed limits . In some a reas, speeds
for vehicles tow ing trai lers are lower than for
regular veh icles . .,.

Always apply brakes early. When driving
downhill, shift into a lower gear to use the en­
g ine braking effect to slow the vehicle . Use of
the brakes a lone can cause them to overheat
and fail.
Coolant temperature
The coolant temperature gauge ¢ page 11
must be observed carefully. The coo lant tem­
perature can increase if you drive on long in­
clines in a low gear at high engine speeds. Re­
duce your speed immediately if the LEDs in
the top part of the display turn on .
For more information about indicator lights,
refer to.
c> page 16.
A WARNING
Anyone not properly restrained in a mov­
ing vehicle is at a much greater risk in an
accident . Never let anyone r ide in your car
who is not properly wearing the restra ints
provided by Aud i.
Trailer towing tips
Important to know
Your vehicle hand les different ly when towing
-
a trailer because of the additional weight and
d ifferent weight distribution . Safety, perform­
ance and economy w ill greatly depend on how
carefully you load your trailer and operate
your rig .
Before you actually tow your trailer, practice
turning, stopp ing and backing up in an area
away from traffic . Keep practicing until you
have become completely familiar with the way
your veh icle-trailer comb ination behaves and
responds .
Backing up is diff icult and requires practice .
Backing up with a tra iler genera lly requires
steer ing action opposite to that when backing
up your vehicle without a trailer.
Maintain a greater distance between your ve­
hicle and the one in front of you. You will need
more room to stop. To compensate for the
Trailer towing 211
trailer, you wi ll need a larger than normal
turning radius.
When passing, remember that you cannot ac­
ce lerate as fast as you norma lly would be­
cause of the added load. Make sure you have
enough room to pass. After passing, allow
plenty of room for your trailer before chang­
ing lanes again.
Avoid jerky starts, sharp turns or rapid lane
changes.
(0 Tips
- Do not tow a trailer during the break-in
period of your vehicle.
- If you tow a trailer, your Audi may re­
quire more frequent maintenance due to
the extra load¢
page 289.
Parking on a slope
Do not pork on a slope with a trailer . If it can­
not be avoided, do so only after doing the fol­
lowing:
When parking:
"' App ly the foot brake .
.,. Have someo ne p lace chocks under both the
veh icle and the trailer wheels.
"' With chocks in place, slowly release the
brakes until the wheel chocks absorb the
load .
.,. Turn the wheels towards the curb .
.,. Apply the parking brake.
.,. Select the P selector lever posit ion .
When restarting after parking:
.,. Apply the foot brake.
.,. Start the engine .
.,. Select the D/S se lector lever position .
.,. Release the parking brake and slowly pull
out and away from the wheel chocks.
.,. Stop and have someone retr ieve the wheel
chocks .
111>
•
•

212 Trailertowing
If you move the selector lever of the auto­
mat ic transm ission to P before app lying
the park ing brake and before blocking the
wheels, you may have to use mo re force
later to move the lever out of the P posi­
tion .

218 Cleaning and protection
8_ WARNING
Always read and heed all WARNINGS and other information
Q page 213 .
Touch-up paint
Minor paint damages should be touched up
immediately.
.. Use either a to uch -up paint stick or spray
paint to cover minor scratches and nicks .
Your Audi dea ler has touch-up paint for minor
scratches and stone chips. Scratches shou ld
be touched up soon after they occur to pre­
vent corrosion.
If a spot starts to rust, however, a simple
touch-up job will not be enough . The affected
surface must be sanded smooth and coated
with an anti-rust primer before the painted
finish can be restored.
The number for the origina l vehicle paint can
be found on the vehicle identification label
r::>
page 2 85.
A WARNING
Always read and heed all WARNINGS and other information
Qpage 213.
Windows
Clear vision to all sides.
Clean all windows regularly to remove road
fi lm and car wash wax buildup.
.. Remove sno w from windows using a brush.
.. Use a plastic ice scraper to remove ice from
windows and mirrors .
.. Remove other residue on the windows with
a spray -on glass cleaner.
.. Wipe the windows dry with a clean p iece of
cloth or kitchen paper towel.
The best way to remove snow from windows
and mirrors is to use a brush . Use a non-abra­
sive
plastic ice scraper -better still, a spray
deicer - to remove
ice from windows and mir­
rors . Oil, grease or silicone residue can be removed
with
glass cleaner or silicone remover . How­
ever, wax res idue requires the use of a spec ial­
ly formulated so lvent. Please contact your
Audi dealer for adv ice on safe products for
wax removal.
Windows should also be cleaned on the inside at regu lar intervals.
Never dry windows with the same chamois
that you use to dry painted surfaces . Wax resi­
due on the chamois can impair v is ion through
the windows.
A WARNING
- Always read and heed all WARNINGS and
other information
Q page 213 .
-The windsh ield must not be treated w ith
water-repellent materials. They can in­ crease glare under poor v is ib ility condi­
tions such as wetness, darkness, or when
the sun is low on the hor izon. In addi­
tion, they can cause the windshield wip­
ers to chat ter.
(D Note
- Never use warm or hot water to remove
snow and ice from windows and mirrors.
Thi s could cause the glass to crack .
- To prevent damage to the wires of the
rear defogger, do not place any adhesive
st ick ers on the inside of the rear win dow
over the wires.
- To help prevent dirt from scratching the
w ind ow, always scrape in a forward di­
rection -pushing the scraper away from
you -never back and forth .
Cast (light) alloy wheels
Cast (light) alloy wheels require special care .
.. Wash the wheels with a sponge or hose
brush every other week.
.. For deep cleaning afterwards, use only a
dedicated
acid-free cast alloy wheel cleaner.
.. Rub a coat of
liquid wax onto the rims every
three month . Be sure to reach and treat all
parts of the rim.
...

222 Cleaning and protec tio n
and can damage the leather surface as well as
weaken seams .
The leather shou ld be cleaned reg ularly as
needed. After having been used for a re latively
l ong time, your leather seats will acquire a
rich ag ed finish. This is a characteristic of nat­
ura l leather and a sign of true quality .
I n order to ma in tain the va lue of th is natura l
p rod uct over the life of your vehicle, you
should follow the recommendations below :
(U;) Note
-To keep your leather from bleaching ou t,
do not a llow it to be exposed to bright
sunlight for long periods of time .
If you
have to leave the vehicle parked outside
for long periods, cover the leather to protect it from d irect exposure to sun­
li ght.
- Sharp objects on clothing, such as zip­
pers, rivets or sharp pieces on belts can
leave permanent scratches or scrape
marks on the surface of the leather .
(D Tips
-After each t ime you clean the leather and
at regular intervals, use a leather preser ­
vat ive creme that conta ins UV-blockers
and that works into the leather. This
creme wi ll nourish and moistur ize the
l eather, helping i t to breathe and stay
supple. It also helps to b uild up a protec­
tive coating on the surface .
- Clean the leather every 2 -3 months,
and clean any areas that get soiled.
- Remove fresh mar ks made by ba llpoi nt
pens, ink, lipst ick, shoe polish, etc. as
soon as possib le .
- Preserve the colo r of the leather as need­
ed by using a special colored leather care
creme to touch up areas of uneven co lor.
Cleaning and caring for leather
upholstery and trim
Appl ies to vehicles : wi th natural lea the r
Natural leather requires special care and at­
tention .
Normal cleaning
.. Clean soiled areas with a slightly moistened
cotton or woolen cloth .
More stubborn dirt
.. More stubborn dirt can be remov ed using a
cloth saturated with a mild soap solut ion (2
tablespoons mild liquid soap).
.. Never allow the soap solution to saturate
the leather, and make certain that no water
soaks into the seams .
.. Wipe off the soap so lution with a soft, dry
cloth.
Cle aning spot s
.. Remove fresh wat er-base d spots (suc h as
coffee , tea, juices, blood) with an absorbent
cloth or paper towel.
.. Remove fresh
gre ase or o il-ba sed spot s
(such as butter , mayonnaise, chocolate) with
an absorbent cloth or paper towel, or use
the cleaner from the leather care kit if the
spot has not yet penetrated into the surface
of the leather.
.. Use an oil/grease d issolving spray, if
oil /
gr ease spots ha ve dr ied on.
.. Remove specific k inds of spots (ballpoint
pen, felt marker, fingerna il polish, water­
based pa int, shoe polish, etc .) with a spot
remover specifically fo rmu lated for leather.
L e ather care
.. Every half year use an approved leather care
product (available from your Audi dealer) to
care for the leather .
.. App ly the product very spar ingly.
.. Wipe it off with a damp cloth.
If you have any questions about cleaning and
ca ring for the leather in your vehicle, it is best
to contact your authorized Aud i dea ler, who
will be g lad to help you and tell you abo ut o ur
f ull range of leather care products, such as : .,_

254 Tire s and wheel s
-The use of incorrect tire pressure values
can lead t o acci dents or other damage .
T herefore it is essential that t he driv er
o bserve the specified tire pressure values
for the ti res and the correct pressu res for
the f unct ion of the tire pressure mon itor­
ing system*.
- Always inflate tires to the recommended
and co rrect tire pressure befo re d riving
off.
- Driv ing with under inflated ti res bend
more, lett ing them get too hot resu lting
in t read separation, sudden t ire fa il u re
and loss o f control.
- E xcess ive speed and/ove rloading can
c ause heat bui ld-up, sudden t ire fail ure
and loss o f control.
- If the t ire p ress ure is too low or too high,
the tires w ill wear prematu rely and the
vehicle will not hand le we ll.
- If the t ire is no t flat and you do no t have
to change a wheel immed iate ly, drive at
reduced speed to the nearest service sta­
t ion to check t he tire pressure and add
air as required.
(D Note
Dr iving w ithou t va lve s tem caps can cause
damage to the tire va lves. To prevent this,
always make sure that facto ry installed
valve stem caps on all wheels are secure ly
mounted on the valve.
@ For the sake of the environment
Unde rinflated tires will a lso increase the
fue l cons umption.
Tires and vehicle load limits
There are limits to the amount of load or
weight that any vehicle and any t ire ca n car ry .
A vehicle that is overloaded w ill not handle
well and is more difficult to stop . Over load ing
can no t on ly lead to loss of veh icle contro l,
b ut can also damage impor tan t par ts of the
vehi cle and can lead to s udden tire failure, in ­
cluding a blowout and sudden deflation that
can cause the veh icle to crash. Your safety and that of your passengers also
depends on making sure that load limits are
not exceeded . Vehicle load includes everybody
and everything in and on the veh icle. These
load lim its are technically referred to as the
vehicle's
Gro ss Vehicle Weight Rating
("GVWR").
The "GVWR" includes t he weight of the basic
vehicle, a ll factory installed accessories, a full
tank of fuel, o il, coolant and other fluids plus
maximum load. The max imum load incl udes
the number of passengers that the vehicle is
i ntended to car ry ("seat ing capac ity") with an
ass umed we igh t of 150 lbs (68 kg) for e ach
passenge r at a designated seating posi tion
and the total weight of any luggage in the ve ­
hicle . If you tow a trai ler, the weight of the
trai ler hitch and the tongue weight of the
loaded tra iler must be included as part of the
vehicle load.
The
Gros s Axle Weight R ating ("GAWR") is
the maximum load that can be applied at each of the vehicle's two axles.
The Gross Vehicle Weight Rat ing and the
Gross Ax le Weight Rating are listed on the
safety comp liance sticker label located on the
driver's side B-pillar . Your Audi has 4 seat ing
pos itions, 2 in the front and 2 in the rear for
total seating capacity of 4 . In some vehicles
the re a re 5 seating pos it ions, 2 in the front
and 3 in the rear for tota l seating capacity of
5. Each seat ing position has a safety belt
¢ page 140, Safety belts .
T he fact that there is a n upper limit to yo ur
vehicle's G ross Vehicle Weight Rating means
t h at the total weig ht of whatever is bei ng car­
ried in the vehicle ( in cl udi ng the weight of a
trai ler hi tch and the tongue weight of the
l oaded trai le r) is limited . The more passen ­
gers in the vehicle or passengers who are
heavier than the standard we ights assumed
mean that less we ight can be carried as lug­
gage.
T he tire pressure label on your Audi also lists
the maximum combined weight of a ll of the
occupants and luggage or other cargo that .,..

256 Tires and wheels
6. If your vehicle will be towing
a trailer, load from your trail­
er will be transferred to your
vehi cle. Consult thi s manual
to determine how this re­
duces the available car go
and luggage lo ad capacity of
yo ur vehicle .
.,. Check the tire sidewall
(9 fig . 200 ) to de termine the
de signated load rating for a
s pe cifi c tir e.
Tire service life
The s ervi ce life of tires dep ends on a lot of
different things including proper installation
and balancing, correc t tire pressu re and driv­
ing style.
Fig. 198 Tire tread: tread wea r ind icators ( TWI)
Fi g. 1 99 Rotat ing t ires fo r m ore eve n wear
Tread W ear Indicator (TWI)
The o rigi na l t ires on your ve hicle have
1/16 inch (1.6 mm) high "wear indicators" ¢
fig. 198 r
u nning across the tread. Depend­
ing on the make, t here will be six to eight of
them even ly placed aro und the tire. Marks on
the tire sidewall (for examp le "TWI" or other
symbols) ind icate the positions of the tread
wear indicato rs . Wor n tires must be rep laced.
D iffere nt f igures may apply in othe r countr ies
Q ,&. .
Tire pressure
Incorrect t ire pressure ca uses premature wear
and can cause sudde n tire blow-out. For this
reason, tire pressure must be checked at least
o nce a month ¢
page 2 52.
Driving style
Driving fast around c urves, heavy acce lerat ion
and hard braking increase tire wear .
Rotating tires for more even wear
Fo r all four tires on your ve hicle to have the
same service life, we recommend that the
front and rear t ires a re rotated according to
the tire manu fact urer's suggested tire rota­
tion intervals. Please remember the follow­
ing :
- Tire rotation intervals may differ from t he
veh icle service interva ls outlined in your
Warranty
& M aintenance booklet.
- The longer one tire is used in one location
o n t he vehicle, the more it wears at certain
points; theref ore, we recommend t hat y ou
follow the tire manufacturer's suggested
tire rotation int ervals .
- Veh icles w ith front-wheel dr ive experience
more tread wear on the fro nt wheels com­
pa red to a ll-wheel drive ( quattro ®).
- Please rotate tires as shown¢
fig. 199.
- Extra care must be taken when rotating di-
rection-specific tires ¢
page 274.
Wheel balancing
The wheels on new ve hicles are balance d.
Howeve r, various s ituations during everyday
dr iv ing can cause them to become unba l­
anced, resulti ng in vibrations you can usually
feel th rough the steer ing wheel.
liJJ,-

What do I do now? Emergency warning
triangle
App lies to vehicles: with emerge ncy warning triangle
The warning triangle is located on the inside
of the trunk lid .
"' M ~
D -~ .. m
!I l
Fig. 203 Trun k lid: Warn ing triang le
.,. To open the cover, turn the locking mecha­
nism and pull the cover downward .
.,. Remove the warning triangle from its hold­
er.
The rear lid is only designed to ho ld the warn­
ing triangle offered by the original accessories
program. If you would like to retrofit your ve­
hicle with a warning triangle, p lease contact
your authorized Audi dealer.
Vehicle tool kit
Vehicle tool kit and jack
The vehicle tool kit is located in the luggage
compartment under the cargo floor cover.
F ig . 204 Luggage compa rtment: cargo floo r cover
folded upward/spa re tire
What do I d o now ? 267
Fig. 20 5 Trunk lid: Veh icle too l kit
.,. Fold the floor to the seatback with the help
of the handle .
.,. Turn the handwheel counter- clockwise
q fig. 204 and remove the spare t ire to
reach the vehicle tool kit.
T he onboard tool k it includes:
- Hooks to remove the whee l covers*
- Plastic hook to remove wheel bolt covers*
- Wheel bolt wrench
-Alignment pin for changing wheels
- Screwdriver with reversib le blade
- Tow ing loop
-Jack
Before storing the jack, make sure it is wound
back down as far as it will go.
A WARNING
Im proper use of the vehicle jack can cause
serious personal injuries.
- Never use the screw driver hex head to
tighten w heel bolts, since the bolts can­
not attain the necessary tighten ing tor­
que if you use the hex head, potentially
causing an ac cident.
- The factory-supplied jack is intended on­
ly for yo ur vehicle model. Under no c ir­
cumstances sho uld it be used to lift
heavy ve hicles o r other loads; yo u risk in­
juring yo urself.
- Never start the engine when the vehicle
is raised, wh ich co uld cause an acc ident.
- Support the vehicle secu rely with appro­
pria te stands if wor k is to be per formed
underneath the vehicle; otherwise, there
is a potentia l risk for injury.