display AUDI A8 2014 Owner's Manual

80 Warm and cold
Operation
We recommend pressing the
IAUTOI button and setting the temperature to 72 °F (22 °C) .
Fig. 81 Cockp it co ntrols
Fig. 82 four zone automat ic climate co ntrol: rea r con ·
trols
Press the buttons to turn the functions on o r
off . Use the dials to adjust the temperature,
the blower speed and the air distribution. The
LED in a button will light up when the func­
tion is sw itched on. The settings are shown in
the climate control display and are also shown in the MMI display for a few seconds . The driv ­
e r and front passenger sett ings can be adjust­
ing separately.
You can also adjust the rear left and right
sides in the four zone automat ic climate con ­
trol*
~ fig . 82.
IOFF i Switching the climate control
system on/off
The I O FFI button switches the climate co ntrol
system on or off .
It also switches on when you
turn the dial or press any button. Airflow from outside is
blocked when the climate control
system is switched off .
You can activate the residual heat function
whe n the ignition is off by pressing and hold­
ing the ~ button. The residual heat from the
coolant is used to heat the vehicle interior .
The resid ua l heat function switches off a uto­
matically after about 30 minutes.
iAIC i Switching cooling mode on/off
The air is not coo led and humidity is not re­
moved when cooling mode is switched off.
T his can cause fog on the windows. Cooling
mode switches off automatically when the
outside temperature is be low zero .
1-1 Switching recirculation mode on/off
In recircu lation mode, the air inside the vehi­
cle is circulated and filtered . This prevents the
u nfiltered air outside the vehicle from enter ­
ing the vehicle interior . We recommend
switching recirculation mode on when driving
through a tunne l or when sitting in traffic
q .&. .
The !AUTO I button or~ button switches reci r­
cu lation mode off.
iAUTOi Switching automatic mode on
Automat ic mode maintains a constant tem­
perature inside the vehicle. Air temperature, .,._

82 Warm and cold
(D Note
To avoid damage to the heating e lements
in the seats, do not kneel on the seats or
place heavy loads on a small area of the
seat .
Setup
The climate control system setup is accessed
through the MMI.
.. Se lect : ICAR !function button> C ar sys tems
control button > A/C.
Rear c abin settings *
When this function is selected, all se tt ings fo r
the rear ca n be adjusted through the climate
contro l system in the cockpit . The climate
control system settings cannot be adjusted in
the rear seat at the same time. This function
switches off after a certain period of time or
when one of the dials in the cockp it is press­
ed .
Auto re ci rculati on* Solar roof*
Pa
rking ventilation is cont ro ll ed automatically
in the
auto setting .
When the ignition is off, solar-powered park­
i ng ventilat io n may sw itch on, as long as
- there is sufficient sunlight,
- the outside temperature is not too low,
- the sunroof is closed or tilted and
- auto (MMI) is selected .
Ii!] Steering wheel heating
Applies to vehicles: wit h heated s tee rin g wheel
The steering wheel rim can be heated.
Fig. 83 Steer ing col umn: steering w heel h eat ing but-
The sensitivity level of the automatic reci rcu-to n
lation mode can be set at various leve ls from
off to sensiti ve . The recirculation mode I""' ! is
controlled on automatically. You must press
the ~ button if fog forms on the w indows.
Fo otwell temperature
You can a dju st the footwell temperat ure so
that it is cooler or warmer.
Windshield heat*
When the defroster~ is swi tched on an d the
Aut o sett ing is selected, the windshie ld de ­
froster is controlled automatically .
Supplementary heater*
The supplementary heater warms the interio r
of vehicles with diesel engines* mo re q uic kly.
The supplementa ry heater is contro lled auto­
matica lly in the
Aut o setting. ..
Press the~ button to switch steer ing whee l
heati ng on/off. The message
Steerin g wheel
h eating on! /Steering wheel heating off!
appears in the instr ument cl uster display .
T he tempera ture is main tained a t a constant
level when stee ring wheel hea ting is switc hed
on .
The steer ing wheel heating sett ings a re stor­
ed automat ica lly and assigned to the remote
c ontrol key that is in use.

Stee ring lock
The stee ring locks when you t urn the engine
off us ing the
I S TAR T ENGINE STOP! button
and open the driver 's door . The locked steer­
i ng he lps pr event ve hicle theft.
E mergenc y off
If necessary , the eng ine can be sw itched off
with the selector leve r in the R, Dor S pos i­
tions . The engine stops i f you press the
I S TART ENGINE STOP! button at speeds below
6 mph (10 km/h) .
.&_ WARNING
- Never turn off the eng ine before the ve­
hicle has come to a complete stop. The
full function of the brake booster and the power steering is not quaranteed. You
must use mo re force to turn or brake if
necessary. Because you cannot steer and
brake as you usua lly would, this could
lead to crashes and serious injur ies.
- For safety reasons, you shou ld always
par k your vehicle with the se lector lever
in P. Otherwise, the veh icle co uld inad ­
vertent ly roll away .
- After the engine has been switched off,
the radiator fan can continue to r un for
up to 10 mi nutes -even with the ignition
switched off.
It can a lso switch on aga in
after some time if the coolant tempera­
ture rises as the result of a heat buildup
or if the engine is hot and the engine
compartment is addit ionally heated by
the sun's rays .
0 Note
Do not stop the engine immed iate ly after
hard or extended dr iving . Keep the engine
r u nning for approximately two minutes to
prevent excessive heat build-up.
Driver message in the instrument
cluster display
Turn off ignition before leaving car
On th e ro ad 85
This message appears and a warning tone
sounds if you open the driver's door when the
ignition is sw itched on.
Pre ss brak e pedal t o sta rt engine
This message appears if yo u press the
I STAR T ENG IN E S TOP I button to start the en­
gine and do not dep ress the br ake pedal. The
engine can only be s tarte d if the brake pedal
is depressed.
I!! I s key in th e vehi cle?
If the indicator light turns on and the mes­
sage appears, the remote control key was re­
moved from the vehicle whi le the engine was
run ning . If the ignition key is not in the veh i­
cl e you will not be able to swi tch on the igni­
tion or res tart the engine after i t has been
switched off. You will a lso not be able to lock
the ve hicle from the outsid e.
Shift to P, oth erwi se v ehicle can roll aw ay.
Do ors d o n ot lo ck if lever is not in P .
This dr iver message appears for safety rea­
sons if the transmission has not bee n shifted
to the P position when you switc h the ign ition
off . Move the selec to r l ever to the P posi tion .
Otherwise the vehicle is not protected from
ro lling and cannot be locked.
fl Key is not r ecognized. Hold back of key
again st marked area . See ow ner' s m anu al.
If the indicato r light turns on and this mes­
sage appea rs, there is a malfunct ion
~ page 86.
Turn off ign ition before lea ving ca r. Battery
is d is c harging
This message appears if the driver's door is
opened wh ile the ignition is switched on . Al­
ways switch off the ign it ion if you a re leav ing
the ve hicle . See also
Q page 90 .
Shift to P and turn off ignition before lea v­
ing car, otherwi se v ehicle can roll away
T his messag e app ears if the driver's door is
opened wh ile the ignition is switched on and
the selector lever is not in the P posit ion. Shift
the selecto r lever into the P pos ition and .,..

Emergency brake function
An emergency brake ensures that the vehicle
can be slowed down even if the
normal brakes
fail
c::> page 88, Emergency broking.
Ind icator light s
-If the par king b rake is closed w ith the igni­
t ion
s wit ched on the indicator lights come
on - (USA models)/ . (Canada models)
in the instrument cluster and in the switch.
- If the par king brake is closed w ith the igni ­
tion
s witc hed off the indicator lights come
on - (USA models)/ . (Canada models)
in the instr ument cluster and in the switch
for about 20 seconds.
A WARNING
Do not press the accelerator peda l inadver­
tently if the vehicle is stat ionary but the
eng ine is running and a gear is selected.
Otherw ise the vehicle will start to move
immediately and cou ld result in a crash.
(D Note
If the symbol . in the display or the ind i­
cato r light
1111 (USA models) . (Cana­
da models) in the instrument cluster flash­
es, the re is a malfunction in the bra ke sys­
tem. Please refer to t he detai led descr ip­
t ion of the indicator lights¢
page 14.
- If the indicato r light - (USA mod-
els) . (Canada mode ls) or
IIJ t ur ns
on, there may be a malfunction in the
parking brake
r=> poge 15.
@ Tips
-You can apply the pa rking brake at any
time -even w ith the ignition swi tched
off. The ignition must be on and the
brake pedal must be pressed in order to
release the parking brake.
- Occasiona l noises when the parking
brake is applied and re leased are norma l
and are not a ca use for concern.
- When the vehicle is parked, the parking
brake goes through a se lf-test cycle at
On th e ro ad 87
regular inte rva ls. Any associated noises
are normal.
· Parking
.. Press the brake pedal to stop the veh icle.
.. Pull the switch(®) to set the parking brake.
.. Select the P selector lever posit io n
c::> poge 116.
.. Tu rn the engine off c::> .&_ .
.,. When on inclines o r declines, tur n the steer­
ing wheel so that your veh icle w ill ro ll into
t he c urb if it beg ins to move.
A WARNING
-==
- When you leave your vehicle -even if on-
ly briefly -always take the ignition key
with you. This applies particularly when
children remain in the vehicle. Otherwise
the children cou ld start the engine, re­
lease the parking brake or operate elec­
trical equipment (e.g. powe r wi ndows).
T here is the r is k of an accident.
- When the veh icle is locked, no one -par­
ticularly not children should rema in in
the vehicle. Locked doors ma ke i t mo re
diff icult for emergency wo rke rs to ge t in­
to the veh icle -putt ing lives at risk.
Starting from rest
The starting assist function ensures that the
parking broke is released automatically upon starting.
Stopping and applying park ing brake
.. Pull the sw itch(®) to apply the parking
brake .
Starting and automatic ally releasing the
parking brake
.. When you sta rt to dr ive as usual, the park­
ing brake is automatically released and your
veh icle begi ns to move.
When stopping at a traffic signal or stopping in city traff ic, the parking brake can be ap-
plied . The vehicle does not have to be he ld
IJ>-

(D Tips
If you switch the system off during a stop
phase, the engine will start again auto­
mat ically.
Messages in the instrument cluster
display
App lies to vehicles: with Start -Stop-System
Start-Stop system deactivated: Please re­
start engine manually
This message appears when specific condi­
tions are not met dur ing a stop phase and the
Start-Stop-System will
not be able to restart
the engine.
If the Dor R selector lever posi ­
tions were engaged, P will be selected auto­
matica lly. The engine must be sta rted with
the
! S TAR T ENGINE ST OPI button.
Start-Stop system: System fault! Function
unavailable
There is a malfunct ion in the Start-Stop-Sys­
tem . Dr ive the veh icle to an authorized repair
fac ility for servicing as soon as possible to cor­
r ect the malfunction.
Speed warning system
Introduction
The speed warning system helps you to stay
under a specified maximum speed.
The speed warning system warns you if you
are exceeding the maximum speed that you
have set. You will hear a warning tone when
your speed exceeds the stored value by ap­ prox imately 3 mph (3 km/h) . An indicator
light . (USA models)/ . (Canada models) in
the instrument cluster display also turns on at
the same time . The indicator light ••
turns off when the speed decreases below the
stored maximum speed.
Sett ing a thresho ld is recommended if you
wou ld like to be reminded when you reach a
cer tain maximum speed. Situations where you
may want to do so include driving in a country
On the road 91
with a general speed limit or if there is a
specified max imum speed for winter tires .
@ Tips
Even though your vehicle is eq uipp ed w ith
a speed warning system, you should still
watch the speedometer to make sure you
are not dr iv ing faster than the speed limit.
Setting the threshold
You can set, change and delete the threshold
in the MMI.
.. Select: !CAR I function button> Car systems
cont rol button > Driver assist > Speed warn·
ing .
You can set any threshold between 20 mph
(30 km/h) and 150 mph (240 km/h) . Sett ings
can each be ad justed in increments of 5 mph
(10 km/h).
Cruise control
Switching on
The cruise control system makes it possible to
drive at a constant speed starting at 20 mph (30 km/h) .
0
f
~
0
Fig. 91 Contro l le ver with s et bu tto n
Fig. 92 Disp lay: Se lecte d speed

92 On the road
• Pull the lever to position CD ¢ fig . 91 to
switch the system on.
• Drive at the speed you wish to set .
• Press button @to set that speed.
The stored spee d and the ind icator light
[ij;(i)~i~ (US mode ls) ,ii (Canadian mode ls) ap­
pear in the instrument cluster d isplay
¢ fig. 92. The display may vary, depending on
the type of d isplay in your vehicle .
The speed is kept constant via an engine o ut­
p ut adjustment or act ive brake intervention .
A WARNING
-Always pay attention to traffic even when
the cruise control is switched on . You are
always responsible for your speed and
the distance between your vehicle and other vehicles.
- For safety reasons, the cruise control
should not be used in the city, in stop­
and-go t raff ic, on twist ing roads and
when ro ad conditions are poor (such as
ice , fog, grave l, heavy rain and hydro­
planing) -risk of accident.
- T urn off the cruise control tempor aril y
when entering turn lanes, highway exit lanes or in construction zones.
- Please note tha t inadvertent ly "rest ing"
yo ur foot on the accelerator peda l causes
the cruise control not to brake. This is
because the cr uise control is overridden
by t he driver 's acce lerat ion.
- If a brake system malfunction such as
overheat ing occurs when the cru ise con­
tro l system is sw itched on, the braking
function in the system may be switched
off . The other cruise control functions re­
ma in active as long as t he indicator light
[ij;rn~i~ (US models) Iii.I (Canad ian mod­
els) is on.
(D Tips
The b rake lights illuminate as soon as the
brakes decelerate automat ica lly.
Changing speed
• To increase/decrease the speed in inc re ­
men ts, tap the lever in the
0 10 direction
¢ page 91, fig. 91 .
• To increase/decrease the speed quick ly, hold
the lever in the
0 10 direction until the de ­
sired speed is displayed.
You can also press the accelerator pedal down
to increase yo ur speed, e.g . if you want to
pass someone . The speed you saved earlier
will res ume as soon as you release the acce ler­
ator pedal.
If, however, you exceed your saved speed by
6 mph (10 km/h) for longer than 5 minutes,
the cr uise control w ill turn off temporari ly.
The green symbol
[ij;(l)~i~ (US mode ls) ,ii in
the d isplay is replaced with a white symbol.
T he saved speed remains the same .
Presetting your speed
You can preset your desired speed while the
vehicle is not moving.
• Switch on the ign ition.
• Pull lever into position
CD ¢ page 91,
fig . 91 .
• Press the lever in t he 0 o r 0 direction to
increase or decrease your speed .
• Release t he lever to save that speed .
Th is function makes it possib le, for examp le,
to save the speed you want before dr iv ing on
the highway. Once on the h ighway, act ivate
the cr uise con trol by pulling the leve r toward
CD -
Switching the system off
Temporary deactivation
• Press the brake pe dal , or
• Press the lever into posi tion @(not cl icked
into p lace)
¢ page 91, fig. 91, or
• Drive for longer t han S m in utes at more
than 5 mph (10 km/h) above the stored
speed.

96 Audi adaptive cruise control and braking guard
@ is located in front of that vehicle, the sys­
tem will not react to the stationary vehicl e.
Audi adaptive cruise
control
Description
Applies to vehicles: with Audi adaptive cruise control
Fig. 96 Detectio n range
What can adaptive cruise control do?
The adaptive cruise control system uses video,
radar and ultrasou nd . Moving vehicles ahead
can be recognized up to about 650 feet (200 m) away.
On open roads w ith no traffic, adaptive cruise
control works like a regular cruise control sys­
tem . The stored speed is maintained . When
approaching a moving vehicle detected up
ahead, the adaptive cruise control system au­
tomatically s lows down to match that vehi­
cle's speed and then maintains the distance
that the driver previous ly stored. As soon as
the system does not detect a vehicle up
ahead, adaptive cruise control accelerates
back up to the stored speed.
In stop-and-go traffic, adapt ive cru ise control
can brake until the vehicle stops and acceler ­
ate again under certain conditions and if this
is possible within the system's limits and ca­
pabilities ¢
page 98. Adaptive cru ise control
will not make an emergency stop .
Which functions can be controlled?
When you switch adaptive cruise contro l on,
you can set the current speed as the "control speed" ¢
page 96, Swi tching on and off.
When driving, you can stop cruise control
¢
poge 98 or change the speed¢ page 97
at any time .
You can also set the distance to the object
ahead and set the adaptive cruise control driv­
ing program ¢
page 98.
Switching on and off
Applies to vehicles: with Audi adaptive cruise control
Fig. 97 Se le cto r lever: swit chin g on /off
Fig. 98 Instrume nt cl uste r: adapt ive cruis e cont rol
You can set any speed between 20 mph and
95 mp h (30 and 150 km/h) .
Ind icator lamps and messages in the instru ­
ment cluster d isplay inform you about the cur­
rent system status and settings .
Switching adaptive cruise control on
... Pull the leve r toward you into position (D
¢ fig. 97 . ACC standby appears in the in­
strument cluster display .
Setting the speed and activating
regulation
... To set the current speed, press the ISETI bu t­
ton ¢
fig. 97. T he set speed is shown in the
tachometer @and is a lso shown br iefly in
the display @¢
fig. 98 . ...,

Audi adaptive cruise control and braking guard 97
.. You must also press the b rake pedal when
the vehicle is stopped.
Switching adaptive cruise control off
.. Push the lever away from you into position
@ until it clicks into place. The message
ACC off appears.
@ Indicator lights
fl -Adaptive cruise control is switched on. No
vehicles are detected up ahead . The stored
speed is ma intained.
I -A moving vehicle is detected up ahead .
The adaptive cruise control system regulates
the speed and distance to the moving vehicle
ahead and acce lerates/brakes automatica lly.
f¥i -Adaptive cruise control is switched on. A
mov ing vehicle up ahead was detected . Your
veh icle remains stopped .
I· When automatic braking is not able to
keep enough distance to a previously detected
mov ing vehicle up ahead, you must take con­
trol and brake
c:::> page 99, Prompt for driver
intervention.
© Display
If adaptive cruise control is not shown in the
d isplay, you can call it up with the multifunc­
tion steering wheel buttons¢
page 24 .
Based on the symbols in the display, you can
determine if the system is maintaining a dis­
tance to the vehicle ahead and what that dis ­
tance is.
No vehicle -No vehicle ahead was detected.
White vehicle -A vehicle ahead was detected.
Red vehicle -Prompt for the driver to take ac­
tion
c:::> page 99.
Both
arrows o n the scale © indicate the dis­
tance to the vehicle ahead . No arrow appears
when the vehicle is on an open road and there
is no object ahead.
If an object is detected
ahead, the arrow moves on the scale.
The green zone on the scale shows the stored
distance. For information on changing the stored distance, refer to
c:::> page 98
. If the
distance selected is too close or may soon be­
come too close, the arrows move into the red
z one on the sca le .
A WARNING
Improper use of the adaptive cruise con­
trol can cause collisions, other accidents
and serious personal injuries.
- Pressing the
!SET ! button when driv ing at
speeds below 20 mph (30 km/h), w ill au­
tomatically accelerate the vehicle to 20
mph (30 km/h), which is the minimum
speed that can be set.
@ Tips
-If you switch the ignit ion or the adaptive
cruise control off, the set speed is erased
from the system memory.
- You cannot switch the Electronic Stabili­
zation Control (ESC) to the SPORT mode
when adaptive cruise control is switched
on.
Changing the speed
App lies to veh icles: w it h A ud i ada ptive c ruise co ntrol
0
f
• 0
Fig. 99 Selector lever: changing the speed
.. To increase or reduce the speed in incre­
ments,
tap the lever up or down.
.,. To increase or reduce the speed q uickly,
hold
the lever up or down until the red LED @
reaches the desired speed
c:::> page 96,
fig. 98.
Follow ing any changes, the new stored speed
will be displayed briefly in the display @
c:::> page 96, fig. 98.

98 Audi adaptive cruise control and braking guard
Driv ing in stop-and-go traff ic
A pplies to vehicles: with Audi adaptive cruise control
The adaptive cruise co ntro l system a lso as­
sis ts you in stop- and -go traff ic. If a previo us
detec ted veh icle ahead s tops, yo ur vehicle will
brake to a stop, within the limits o f the sys ­
tem .
,,. To res ume dr iv ing wi th adap tive cruise con­
t ro l, tap the accelerator pe dal or
,,. Pull the lever toward yo u into posit ion @
¢page 98 , fig. 100.
@ Tips
-If ada ptive cruise con trol is a ctive an d
you r vehicle does not start driving as ex­
pected after pulling the lever once, you
can start out aga in by tapp ing the accel­
erato r pedal.
- If an obstacle is detected when yo ur ve­
h icle starts dr iv ing, the system w ill
prompt you to take over
¢ page 99.
Your veh icle w ill drive more s low ly when
star ting . This may a lso happe n in some
s ituation s whe n no obstacle is apparent.
Interrupting cruise control
Applies to vehicles: with Audi adaptive cruise co ntrol
Fi g. 100 Selecto r lever
Requ irement : adaptive cruise control must be
sw itched on .
Overriding crui se control
,,. To accelerate ma nually, pull the lever to­
ward you into position @and hold it there .
The message
ACC override appears . Or
,,. press th e accelerator peda l. ,,.
To resume cruise cont ro l, re lease the lever
or take your foot off the accelerato r pedal.
Canceling cruise control while driving
,,. Move the lever in to posi tion @. T he mes­
sa ge
ACC standby ap pears. Or
,,. press the brake pedal.
,,. To resume the stored speed, move the lever
into position @.
Canceling cruise control when stopped
,,. Push the lever away from you i nto posit io n
@ . Th e message
ACC standby appe ars.
,,. To resume cruise contro l, press the brake
pedal an d pu ll the lever toward you into po­
sition @.
A WARNING
• -
Never resume the stored speed if the
sp eed is too high for p revailing r oad, traf­
f ic or weat her condit io ns.
Setting the distance
App lies to vehicles: wit h Audi ada ptive c ruise contro l
Fig. 101 Selector lever: setting t he dista nce
,,. Tap the switch to display the current set dis­
tance
r::!> fig. 101 .
,,. To increase or reduce the d istance by incre­
ments, tap the switch again to the left or
r ight. The d istance between the two vehicles
w ill change in the instrument cluste r dis­
p lay .
When approach ing a mov ing vehicle up ahead,
the adaptive cruise control system automati­ ca lly brakes to match that object's speed and
Ill>

Audi adaptive cruise control and braking guard 99
then maintains the stored distance. If the ve­
hicle ahead accelerates, adaptive cr uise con­
trol will also accelerate up to the stored
speed.
The higher the speed, the greater the distance
in yards (meters) ¢.&. . The
Distance 3 setting
is recommended .
The distances prov ided are spec ified values.
Depending on the driving situation and the
how the vehicle ahead is driving, the actual
d istance may be more or less than these tar­
get distances.
The various symbols for the time increments
appear briefly in the information line @
¢ page 96, fig. 98 when you change the set­
tings.
~ -~ --- Distance 1: This setting corre­
sponds to a distance of 92 feet/28 meters
when traveling at 62 mph (100 km/h), or a
time interva l of
l second.
~ -- ~-- Distance 2: This setting corre­
sponds to a distance of 118 feet/36 meters
when traveling at 62 mph (100 km/h), or a
time interva l of 1.3 seconds .
~--- ~-Distance 3: This setting corre ­
sponds to a distance of 164 feet/SO meters
when traveling at 62 mph (100 km/h), or a
time interva l of 1.8 seconds .
~---- ~ Distance 4: This setting corre ­
sponds to a distance of 210 feet/64 meters
when traveling at 62 mph (100 km/h), or a
time interva l of 2.3 seconds .
A WARNING
Following other vehicles too closely in­
creases the risk of collisions and serious
personal injury.
- Setting short distances to the traffic
ahead reduces the time and distance
available to br ing your vehicle to a safe
stop and makes it even more necessary
to pay close attention to traffic.
- Always obey applicable traffic laws, use
good judgment, and select a safe follow- ing distance
for the traffic, road and
weather conditions.
@ Tips
- Distance 3 is set automatically each time
you switch the ignition on.
- Your standard settings are automatically
stored and assigned to the remote con­
tro l key being used.
Selecting the driving mode
Applies to vehicles: with Aud i adapt ive c ruise contro l
.,. Select the desired driving mode in drive se­
lect¢
page 110.
(0 Tips
Your settings are automat ica lly stored and
assigned to the remote control key being
used.
Prompt for driver intervention
Applies to vehicles: with Audi adapt ive cru ise contro l
Fig. 102 Instrument cluster: request fo r drive r in ter­
vent ion
In certa in situations, the system will prompt
you to take action . Th is could happen, for ex­
amp le, if braking by the adaptive cruise con­
trol system is not enough to maintain enough
distance to the vehicle ahead.
The indicator light
I and the symbol in the
display will warn you about the situation
¢ fig. 102. You will also hea r an acoustic sig­
nal.
- Press the brake pedal to slow your vehicle
down.