light AUDI A8 2015 User Guide

,....,
N ,....,
N
0 J:
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Instruments and warning/indicator lights 17
t Safety belts
This warning/indicator light reminds you to
put on your safety belt.
The. warning/ind icator light illuminates
when the ignition is switched on to rem ind
the dr iver and any front passenger to put on
the safety belt. Add itionally, an acoustic warn­
ing (gong) will also sound.
For more Information
c:> page 143, ~ Safety
belt warning light .
~ Engine oil pressure malfunction
The red engine oil pressure warning symbol
requires immediate service or repair . Driving
with a low-oil-pressure indication is likely to
inflict severe damage to the engine.
• Switch off engine and check oil level
If the indicator light turns on and the mes­
sage appears, the oil pressure is too low.
.. Pull
off the road.
.. Stop the vehicle .
.. Turn
off the engine.
.. Check the engine oil level c:> page 233.
.,. If the engine oil level is too low, add engine
o il
c:> page 234. Make sure that the oil pres­
sure warning symbol. appears no longer
in the display before you start driving again.
.,. If the engine oil level is correct and the indi­
cator light still turns on, turn the engine
off
and do not continue driving. Seek professio­
nal assistance.
(D Tips
- The engine oil pressure symbol. is
not an indicator for a low engine oil lev­
el. Do not rely on it. Instead, check the
oil level in your engine at regular inter­
vals, preferably each time you refuel,
and always before going on a long trip.
- The yellow oil level warning indication
1111 requires oil refill or workshop serv­
ice without delay. Do not wait until the
red oil pressure warning. starts to
flash before you respond to the low oil level warning
Ill. By then,
your engine
may already have suffered serious dam­
age.
~~ Engine oil level
• WARNING: Please add oil immediately
If the indicator light and the driver message
appear, add engine oi l immediate ly
c:> page 231.
1111 Add oil, max. x qt (l). You may continue
driving
When the symbol and the driver message ap­
pear, add the amount of oil appearing in the
display at the next opportunity
c:> page 231.
@I-Steering column lock
• Do not drive vehicle: Steering defective
If the indicator light turns on and the mes­
sage appears, there is an electronic stee ring
column lock malfunction . You cannot switch
the ignition on .
Do not tow your vehicle because it cannot be
steered. Seek professiona l assistance .
1\1 Steering lock : system fault. Please con­
tact dealer
If the indicator light turns on and the mes­
sage appears, there is an electronic steering
column lock malfunct ion .
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected .
A WARNING
Your vehicle must not be towed in the
event of a malfunction in the electronic
steering column lock because it cannot be
steered due to the locked steering. If it is
towed with the steering locked, there is
the r isk of an accident.
©-Engine start system
• Engine start system fault . Please contact
dealer ..,.

18 Instruments and warning/indicator lights
If the indicator light turns on and the mes­
sage appears, do
not switch the ignition off
because you may not be able to switch it on
again.
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
Ill Engine start system fault. Please contact
dealer
If the indicator light turns on and the mes­
sage appears, there is a malfunction in the en­
gine start system.
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
0 Air suspension
• Air suspension: system fault. Can contin­
ue slowly with max. 35 mph.
There is a malfunction that can result in re­
stricted driving stability.
Carefully drive at a maximum speed of 35
mph (60 km/h) to your authorized Audi dealer
or qualified workshop to have the malfunction
corrected .
• Air suspension: service mode. Vehicle can
only be moved with restrictions
Carefully drive to your authorized Audi dealer
or qualified workshop immediately to have
the service mode deactivated.
II Air suspension fault
There is a system malfunction that can result
in restricted driving stability or reduced
ground clearance.
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
II Air suspension: vehicle too low. Ground
clearance reduced
The ground clearance is very low due to a sys­
tem malfunction . Wait until the air suspen ­
sion system has restored normal ground clear­
ance. Otherwise, conditions such as an uneven
road surface can lead to vehicle damage.
AIR/ e;, 5 f BAG -, a ety systems
The II (USA models),fll(Canada models) in­
dicator light monitors the safety systems e.g.
airbags, pretensioners and illuminates for a
few seconds each time you switch the ignition
on.
If the
II (USA models)/E,I (Canada models)
indicator light does not go out, or if it illumi­
nates while you are driving, or if it starts to
blink, then there is a malfunction somewhere
in the system.
If the light does not illuminate
when you switch the ignition on, this also means there is a malfunction.
A WARNING
=
If you have a malfunction in the safety sys-
tems, contact your authorized Audi dealer
immediately. Otherwise the safety sys­
tems may not work properly in an acci­
dent.
~ Brake booster
II Brake servo: limited functionality. You
can continue driving. Contact workshop
There is a brake booster malfunction. The
brake booster is still available, but its function
is limited. Because of this, the vehicle may
brake differently and the brake pedal may vi­
brate.
Drive to an authorized Audi dealer or author­
ized repair facility immediately to have the
malfunction corrected.
Y$/ C, Electronic Stabilization Control
(ESC)
If the Dl indicator light blinks while driving,
the ESC or ASR (Anti-Slip Regulation) is active­
ly regulating.
If the
Dl indicator light turns on, the system
has switched the ESC off. In this case, you can
switch the ignition off and then on to switch
the ESC on again . The indicator light turns off
when the system is functioning fully . .,,.

,....,
N ,....,
N
0 J:
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Instruments and warning/indicator lights 19
If the fl indicator light turns on, ESC was re­
stricted using the
[fil button¢ page 197.
Stabilization control (ESC/ABS): Fault! See
owner's manual
If the: G1 indicator light and the ABS indicator
light
tll1 (USA models) I ii] (Canada models)
turn on and the message appears, the ABS or
e lectronic differential lock is ma lf u nction ing.
This a lso causes the ESC to malfunction . The
brakes sti ll function with their normal power,
but ABS is not act ive .
Drive to your authorized Aud i dea ler or quali ­
fied workshop immediately to have the mal ­
function corrected.
A WARNING
If the . (USA models) . (Canada mod­
els) brake system indicator light turns on
together with the ABS and ESC indicator
lights, the ABS/ESC regulating function
may have failed. Functions that stabilize
the vehicle are no longer avai lab le. This
could cause the vehicle to swerve and in­
crease the risk of sliding. Drive carefully to
the nearest authorized Audi dealer or oth­
er qualified workshop and have the mal ­
function corrected .
(D Tips
For additional information on ESC and
ABS, refer to¢
page 197.
ABS!( @)) Anti-lock braking system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL).
The warning/ind icator light tll1 (USA mod-
e ls)
;tlJ (Canada models) will come on for a
few seconds when the ignition is switched on.
The light will go out after an automatic check
sequence is completed.
There is a malfunction in the ABS when:
- T he warning/indicator light does not illumi­
nate when you switch the ignition on. -
The warning/indicator light does not go out
after a few seconds .
- The warning/indicator light il luminates
while driving.
T he ESC indicator lig ht also illuminates if
there is a malfunction in the ABS. The mes­
sage
Stabilization control (ESC/ABS) Fault!
See owner's manual
also appears in the in­
strument cluster display and a warning tone
sounds.
The brake system will still respond even
without the assistance of the ABS system.
See your authorized Audi dealer as soon as
possible to restore full braking performance.
For more information regarding the ABS
¢pag e 197.
Malfunction in the brake system
If the brake warning light¢ page 14 and the
ABS warning illuminate
together there may be
a malfunction in the ABS, and there may a lso
be a malfunct ion in the brake system itself
¢.&. .The ABS will not work and you will no­
tice a change in braking response and per­
formance.
In the event of a malfunction in the brake
system
the warning/indicator light . (USA
models) . (Canada models) in the instru­
ment cluster flashes ¢
page 14.
Malfunction in the electronic differential
lock (EDL)
The EDL works together with the ABS. The
ABS warning light will come on if there is a
malfu nction in the EDL system ¢
page 197.
See your authorized Audi dealer as soon as
poss ible.
A WARNING
-
-If the tll1 (USA models) ;tl] (Canada
models) warning light does not go out,
or if it comes on while dr iving, the ABS
system is not working properly. The vehi­
cle can then be stopped only w ith the
standard brakes (without ABS). You w ill
not have the protect ion ABS provides. ..,.

20 Instrum ent s a nd w arn in g/i ndic ato r light s
Contact your Audi dealer as soon as pos­
sible.
-USA models: If the . war ning light, the
DJ warn ing light and the fi1 warning
light come on together, the rear wheels
could lock up first under hard braking.
Rear wheel lock-up can cause loss of ve­
hicle control and an accident. Have your
vehicle repaired immediately by your au­
thorized Aud i deale r or a qua lified wor k­
shop. Drive slowly and avo id sudden,
hard brake applications .
-Canada models: If the brake warn ing
light ., the
Ji) warning light and the
ABS warning light
[ill come on together,
the rear wheels could lock up first unde r
hard braking. Rear wheel lock-up can
cause loss of vehicle control and an acci­
dent. Have your vehicle repaired immed i­
ately by your authorized Audi dealer or a
qualified wo rkshop. Dr ive slowly and
avo id sudden, hard brake applicat ions.
(0) Worn brake pads
Ei'I Brak e pa ds!
If the warn ing light illum inates, immediately
contact your authorized Audi dealer or quali­
fied workshop to have all brake pads inspect­
ed. O n USA models the wa rning light
Ei'I
comes on together with t he warn ing light •.
Both sets of b ra ke pads on an axle must a l­
ways be rep laced at the same time.
A WARNING
Dr iv ing with bad brakes can cause a colli­
sion and serious personal injury.
- If the wa rning light
Ei'I and the warning
light
. ll with the message Brake pads!
comes on in the instrument cluster dis­
play, immediately contact your author­
ized Audi dea ler or qualified workshop to
have all brake pads checked or rep laced if
necessary.
l ) . : USA mode ls on ly
EPC Electronic power control
Applies to veh icles: w ith gasoline engine
This warning/indicator light monitors the
electronic power control .
The Di warning/ indicator light (Electron ic
Power Control) illuminates when you sw itch
the ignit ion on as a function check.
(D Tips
If this warning/ indicator light illum inates
while you are driving, then there is a mal­
funct ion in the engine electronics. Have
the malfunct ion corrected as soon as pos­
s ible by your authorized Audi dealer or
qualified workshop.
W Glow plug system
Applies to veh icles: w ith diesel engine
The control light illuminates when the glow
plug system is active.
If the II ind icator light illuminates, the glow
plug system is act ive. You should start the en­
gine immediately after the ind icator light
swi tches off. The ind icator lig ht only illum i­
na tes for approximate ly 1 second if the en­
gine is warm or if the outs ide temperature is
above 46 QF (8 QC).
(D Tips
-If the glow plug indicator l ight i llum i­
nates while dr iving, there is an eng ine
cont ro l ma lfunction. The engine should
be checked immed iate ly .
- If the ind icator light does not illuminate
at a ll when switch ing the ignit ion on,
there may be a malfunction in the glow
plug system. The engine should be
checked.
' o Malfunction Indicator Lamp (MIL)
The Ma lfunction Indicator Lamp ( MIL) is part
of the On-Board Diagnost ic (080 II) system.
T he symbo l¢..,, lights up whe n the ignition is ...

,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Instruments and warning/indicator lights 21
switched on and will turn off after the engine
has started and has sett led at a constant idle
speed . This ind icates that the MIL is working
properly .
The warning light illuminates when there is a
malfunction in the engine e lectronic system .
Contact your author ized Audi dealer and have
the malfunction corrected .
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
¢page 223.
For mo re in format ion ¢ page 29.
~. Diesel particulate filter clogged
Appl ies to vehicles: with d iesel e ngine and diese l pa rticu ­
late fi lte r
II Particulate filter: System fault See own­
er's manual
When the II symbol illum inates, you can al­
ter your driving style to assist the filter self­
cleaning process. Drive for approximately 15
minutes with the selector lever in the 5 posi­
tion at a minimum speed of 37 mph (60 km/
h) and an engine speed of approximately
2,000 RPM. The temperature increase that
will resu lt from this can burn off the soot in
the filter . The symbol will switch off when the
cleaning is successful. After a successful
cleaning , there is no need to bring the car to
an author ized dealer or qualified workshop
because this is part of normal vehicle ope ra­
tion .
If the symbol
II does not switch off, see your
author ized dealer or other qualif ied workshop
to have the problem corrected.
For more information on the diesel particu­
late filter , refer to¢
page 206 .
.,&. WARNING
Always adapt your speed to the current
weather, road and traffic conditions. You
should never disobey traffic laws in order
to follow driving recommendations.
-
!'1 Engine speed limitation
App lies to veh icles: w it h e ngine speed lim itat io n
II! Engine speed maximum XXXX RPM
The engine speed is automatically limited to
the speed d isplayed in the driver information
system. This protects the engine from over·
heating.
The engine speed limitation deactivates once
the engine is no longer in the critical tempera­
ture range and you have released the accelera­
tor pedal once.
If the engine speed limitation was activated
by an engine control malfunction, the indica­
tor light
13:a also turns on . Make sure that the
speed does not go above the speed disp layed.
Drive to your authorized Audi dealer immedi­
ate ly to have the malfunction corrected.
~v, Engine oil sensor
• Oil level! Sensor defective
If the symbol illum ina tes, contact your au­
thorized Audi dea le r and have the oil sensor
inspected. Until you have this done, check the
oi l level each time you refue l just to be on the
safe side
¢ page 233.
f Request to warm engine by driving
0 Please warm up engine
Fuel has entered the engine o il because of low
outside temperat ures or frequent short
drives . Drive until the engine is warm so that
the fuel in the engine oil will vapori ze. Avoid
high eng ine speeds, full acceleration and
heavy engine load when doing this .
Bu Fuel level indicator
liD Please refuel
If the indicator light turns on for the firs t
time and the message appears, there are
about 4 gallons ( 15 liters) of fuel left in the
tank. Time to refuel
¢page 222 .
Ill Tank system malfunction! Contact dealer IJIJ,

22 Instruments and warning/indicator lights
If the indicator light t urns on and th is mes ­
sage ap pears, the re is a ma lfunction in the
tan k system.
D rive to yo ur aut hori zed Au di dealer i mmedi­
ate ly to have the mal func tion cor rected .
¢,- $ Please refill washer fluid
If th e sym bol illum inates, add w indshield
washer fluid to the was her system/ headlight
washer system* ~
page 244 .
6 Windshield wipers
m Windshield wiper defective
There is a mal func tion with the w indshield
wipers.
D rive to yo ur authorized Aud i dea le r i mmedi­
a te ly to h ave the mal fu ncti on cor re ct ed .
~ /}D /0$ Defective light bulb warning
J:J-I f the ind icator light tu rns on, a bulb has
failed. The message indicates the location of
the bulb .
Im-if a fog lamp* h as f ailed , the indic ator
lig ht tu rns on to indica te the location on t he
ve hicl e.
IJ -if a rear fog lam p has fai led , the indic ator
li g ht tu rn s o n to in dicat e the locat ion on t he
ve hicl e.
Vehicle lights: malfunction
If the message appea rs, there is a malfunc­
tion in the headlights or light switch .
Drive to yo ur authorized Aud i dea ler immedi ­
ately to have t he malfunction corrected.
A WARNING
- light bu lbs are pressurized and co uld ex ­
plode while they a re being changed caus­
ing ser ious p erso na l in ju ry.
- Work w it h due care when handling the
hig h-voltage section of gas discha rge (
x enon) lights . Failure to do so cou ld re­
sult in death o r serious injury .
(D Tips
Have the b ulb replaced or the conne ct io n
r epaire d by your authorized A udi Se rvice
department.
~0 Headlight range control
1\1 Headlight range control: defective!
If the symbol illuminates, the headlig ht ran ge
control is no lo nger work ing pro per ly . Have
the system checked and repaired at yo ur A udi
dealer.
§0 Adaptive Light
Applies to vehicles: with Adaptive light
FJl Audi adaptive light: system fault
If the indicator light turns on and this mes­
sage appears, there is a malfunct ion in the
adaptive light system. The headlights still
funct ion .
Go to an authorized dealersh ip to have the
headlights o r the co ntrol un it for the Adaptive
Light repa ired.
@:> Light/rain sensor
£1 Automatic headlights /automatic wipers :
system fault
If the indicator light turns on and this mes­
sage appears , the light/ rain senso r is not
f unct ion ing corr ect ly .
For sa fety reasons the low beams are t urned
o n permanently wit h the sw itch in
AUTO .
However, you can continue to turn the lights
on and off us ing the light switch . Yo u can st ill
co ntrol all func tions that a re independent of
t h e ra in sensor th roug h the w indshi eld wipe r
l ever .
Co ntact your aut horized Aud i dea ler as soon
as possible to have the problem co rrec ted .

Instrument s and warning /indicator lights 23
I--: Sport differential
IIJ Sport differential: system fault
There is a malfunction with the sport differen­
tial.
Drive to your authorized Audi dea ler immedi­
ately to have the malfunction corrected.
IIJ Sport differential: overheating
The transmission temperature has increased
sign ificantly due to the sporty dr iving manner .
D rive in a less sporty manner until the tem­
perature returns to the normal range and the
indicato r light switches of .
.&_ WARNING
-
Contact your authorized Audi dealer or a
qualified workshop if the sport different ial
is faulty or ma lfunctioning. The repa ir
must be performed by trained personnel
using the correct oil in order to ensure
safety.
¢ Q Turn signals
The indicator light blinks when you use either
turn signal.
Whenever you use the left Nor the right a
turn signal, the indicator light blinks. When
you use the emergency flashers, both indica­
tor lights flash .
If one of the turn signal light bulbs burn out,
the turn signal will blink tw ice as fast as nor­
mal. Carefully drive to your authorized Audi
dealer immediately to have the malfunct ion
corrected. The indicator light does not indi­
cate a malfunction if a turn signa l on the trail­
er or on the vehicle fails in trailer towing
mode.
(D Tips
For more information on the turn signals,
refer to¢
page 48.
Driver information
display
Overv iew
Fig . 4 Drive r info rmation system in the inst rument
cluster
Fig. 5 Display: examp le of the info rmat ion lin e
The driver information system contains infor ­
mation @ that is displayed on tabs @
¢ fig. 4. The following content is possible de­
pending on vehicle equipment:
@
®
Tab Content
1 Vehicle
functions :
On-board computer ¢ page 25
Efficiency program*¢ page 26
Digital speedometer
Cruise control*¢
page 90
Adaptive cruise control and braking
guard* ¢
page 92
Audi active lane ass ist* <=> page 101
Display darkened ...

24 Instruments and warning/indicator lights
® ®
Tab Content
2 Indicator lights and messages
Warning when a door, the hood or the rear lid is not closed
c:::>page29
Service interval display c:::>page 27
Speed warning system c:::> page 90
3 Night vis ion assistant* c:::> page 111
4 Audio/video
5 Telephone*
6 Nav
igation *
The second and third tabs are only visib le if at
least one indicator light or message is shown
or if that system is switched on.
The status line© is located in the bottom
part of the display
c:::> fig. 4. It displays the ex­
terior temperature, time, selector lever posi­
tion, trip odometer and odometer.
F or some ve hicle functions, you can access the
trip information from the temporary memory
c:::> page 25 in the line(!) c:::> fig. 5 .
.&_ WARNING
-
-Never rely exclusively on the outside
temperature display to determine if a road surface is icy or not. Keep in mind
that road surfaces, especially bridges and overpasses, could be ice covered and
slippery even at an outside temperature
above 41 °F (+5 °().
- Always reduce your speed and drive with
special care in cold weather conditions
when the chance of encountering icy
road surfaces increases.
(D Tips
-You can select the un its used for temper·
ature, speed and other measurements in
the
MMI.
- If the vehicle is stat ionary, or if you are
driving at a
very low speed, the tempera­
ture shown in the display might be
slightly higher than the actual outside temperature.
This is caused by the heat
being radiated from the engine.
- At temperatures below 41 °F
(+ 5 °C) a
snowf lake symbol appears ahead of the
temperature display
c:::> .&. .
-For information on the audio/video and
navigation* functions, refer to the sepa­
rate
MMI owner's manua l.
Operation
The driver information system is operated us­
ing the buttons on the multifunction steering wheel.
en ..,
8
--------± ~
Fig. 6 Multifunction steering wheel: operating the driv ·
er information system
Fig. 7 Driver information system: open ing the vehicle
func tions men u
Operating concept
.,. Switch the ignition on .
.,. To switch between the tabs, press the rocker
switch ® to the left or right
c:::> fig. 6 .
.,. To access additional information below or
above, rotate the thumbwheel @ down or
up .
.,. To confirm a selection, press the thumb­
wheel @.

Instrument s and warning /indicator lights 25
Access ing Vehicle functions
• Se lect the firs t tab with the rocker sw itch
@ .
• Pr ess the button ~-Th e Vehicle functions
menu app ears <=>fig. 7.
• To select a menu item, tu rn and press the
th umbwheel @.
Resetting values to zero
• Se lect the on-board computer / Efficiency
program
menu item in the Vehicle func­
tions
menu.
• You can now select between the long-term
memory and shor t-term memory .
• To reset the values in a memory, press and
ho ld the thumbwhee l
® for one second .
The last function se lected displays when you
switch the igni tion on.
(D Tips
- All stored va lues w ill be lost if the veh i­
cle battery is disconnected.
- Fuel consumptions (average and cur ­
r ent), range and speed are displayed in
metric units on Canadian models .
On-board computer
F ig. 8 I n str u m en t cl uster : fu el co nsumpt io n
You can call u p the following information in
the on-board computer:
- Date
- Drivi ng time (h) from the s hort- term memo-
ry
- Ave rag e consumption in MPG (l/100 km)
from the sho rt-term memo ry - Average speed in m
ph (km/h) from the
short-term memory
- Dis tan ce driven in miles (km) from the
short-term memory
- Cur re nt fu e l c on sump tion in MPG (l/100
km)
- Short-te rm memory overview
- Long-te rm memory ove rview
The short-term memory collects driv ing infor­
mation from the time the ign it io n is switched
on until it is swi tched off . If you continue driv­
i ng withi n two ho urs after sw itch ing the ig ni­
ti on off, the new values are in clu ded when cal­
cu lat ing the current trip info rm ation .
Unlik e the s hort-term memory, t he long-term
memo ry is not erased automatically . You can
sele ct th e time pe riod for evalua tin g trip in­
f ormat io n yo urse lf.
Fo r some vehicle f unctions, you can access t he
t rip informa tion from t he tempo rary memory
i n t he line
(Dr=> page 23, fig . 5.
Fuel consumption
The current fue l cons umption can be d is­
played using a ba r<=> fig.
8. The ave rage con­
s u mption (mpg) stored in the sho rt-term
memo ry is also displ ayed. W he n t he ba r tu rns
green, yo ur vehicle saves fue l by one of the
f o ll ow ing func tions:
- Recuperation : When the v ehicle is coast ing
or dr iving dow nhill, elec trica l energy can be
s to red in the b attery . T he b ar will move to­
ward
0 .
-Cylinder on demand System* : whe n the de ­
mand fo r p ower is low and ot he r co ndit ions
are met, the engi ne au tomatically deacti­
vates fo ur cyli nders (4 .0 T FSI) or s ix cylin­
ders
(6 .3 F SI). The driver and passengers
w ill not even notice th is. The message
4 cyl­
inder mode
(4 .0 TFSI) or 6 cylinder mode
(6.3 FSI) appears under the bar. The cylin­
ders switch on again when mor e powe r is
needed .

26 Instruments and warning /indicator lights
Efficiency program
App lies to vehicles: with efficiency program
Fig . 9 Tri p com puter: ot her equipment
Fig. 10 D isplay: example of a f uel eco no m y message
The effic iency program can help you to use
l ess fuel.
It shows other eq uipment influenc­
ing consumpt ion and fue l economy messages
p rov ide tips f or efficient driv ing . The efficiency
prog ram uses distance a nd consumption data
from tr ip compute r
1.
To display the efficiency program, ca ll up Ve­
hicle functions
and select the menu option
Efficiency program .
Other equipment
Other equipment that is currently affecting
fuel consumption is listed in t he v iew
Con ­
sumer .
The display shows up to three other
items of equipment @¢
fig. 9. The equip ­
ment us ing the most fuel is listed f irst . If
mo re than three it ems using fue l ar e swit ch ed
on, the eq uip ment th at is cur ren tly using the
most fuel is d isp laye d.
A scale @also shows the cu rrent total con­
sumpt ion of all other equ ipme nt.
Fuel economy messages
F ue l economy messages are disp layed when
fue l consumption is increased by certain con- di
tions ¢
fig. 10 . If you follow these fuel
economy messages, you can reduce you r vehi­
cle's consumpt io n of fuel. The messages ap ­
pear automatically and are on ly disp layed in
t h e efficiency program . The f uel economy
messages tu rn
off automatically after a cer ­
ta in period of ti me.
To turn an economy message
off i mmediately
after it appears, press any button on t he mul­
t if u nct ion steer ing whee l.
@ Tips
- If the data are deleted in the efficiency
program , those values a re a lso reset i n
t rip computer.
- Once you have turned a fuel economy
message
off, it will on ly appear agai n af­
ter you turn the ig nition on again .
- The f uel economy messages are not dis­
played in every instance, but rather in in ­
t ervals over a period of time .
Odometer
Fig. 11 Instrume nt cluster O do m eter a nd r eset button
The odometer shows you how many m iles
(k ilomete rs) you have drive n. You can switch
the d isplay from miles to ki lometers and v ice
versa via the MMI.
Upper odometer
The trip odometer shows the distance driven
since it was last reset . It can be used to meas­
u re s hort dista nces . The last digit indicates
1/10 of a mile (100 meters).
You can reset the trip odometer to zero by pressing the Reset button~-