light AUDI A8 2015 Owner's Guide

42 Opening and closing
Closing the windows
.,. Pull the switch to the first stop and hold it
until the window reaches the desired posi­
tion .
.,. Pull the switch briefly to the
second stop to
automatically close the window.
Power window switches
@ Driver's door
@ Passenger's door
© Left rear door
@ Right rear door
® Safety button (or two safety buttons in
vehicles w ith power child safety locks
r::!) page 41)
Child safety lock
When the safety button®¢ fig. 35 is press­
ed, the LED in the button lights up. The fol­
lowing features are switched off:
- The power windows in the rear doors,
- The buttons for the power sun shades * in
the side windows,
- The buttons for the power sun shade* in the
rear window,
- Front passenger power seat adjustment*
button.
&_ WARNING
- When you leave your veh icle - even if on­
ly brief ly - always take the ignition key
with you. This applies particularly when children remain in the veh icle. Otherwise
the chi ldren could start the engine or op­
erate electrical equipment (e.g. power
w indows). The power windows are func­
tional until the driver's door or passeng­
er's door has been opened .
- Be careful when closing the windows.
C heck to see that no one is in the way, or
serious injury could result!
- When locking the vehicle from outside,
the vehicle must be unoccupied since the
windows can no longer be opened in an
emergency.
(D Tips
- The driver can lower or raise the power
sun shades* in the s ide windows by using
switches © and @.
- After the ignition has been switched
off,
the windows can sti ll be opened or
closed for about 10 minutes. The power
w indows are not switched off until the
dr iver's door or passenger's door has
been opened .
What to do after a malfunction
The one-touch open and close function must
be reactivated if the battery has been discon­
nected .
.,. Pull and hold the power window switch until
the window is fully closed .
.,. Release the sw itch and then pull it again for
at least one second.
Valet parking
The valet parking feature protects the lug­
gage compartment from unauthorized ac­
cess .
Fig. 36 Valet parking button
With "valet parking" activated , the luggage
compartment lid cannot be opened .
.,. Remove the mechanica l key
¢ page 32.
.,. Open the glove compartment and activate
¢ fig. 36 the "valet parking" feature by
pressing the
j VA LETi button . The indicator
light in the sw itch illuminates .
.,. Close the glove compartment and lock it
w ith the mechanical key . .,.

46 Clear vis ion
Clear vision
Lights
Switching the headlights on and off
Fig . 40 Instr ument pane l: lig ht sw itc h w it h all -weath­
er lig hts
The headlights only wo rk when the ignition is
sw itched on. Wh ile start ing the eng ine or
when switching off the ig nition, the head­
lights will go off and on ly the s ide marker
lights w ill be on .
I f the sys tem is not operating properly, a
warn ing symbol in the dr iver information dis­
p lay is displayed <=>page
22 .
Light switch -~ -
Turn the switch <=>fig. 40 to the co rrespond ing
position . When the lights a re switched on , the
:o o: symbo l turns on .
0 -The lights are off or the dayt ime run ning
lights are on:
- US A model s: The daytime running ligh ts
will come on automatically when the igni­
t ion is on and the light switch<=> fig .
40 is in
the
O posit ion or the A UTO position (only in
daylight cond itions) . T he
Daytime running
lights
function can be turned on and off in
the MMI <=> page
47, <=> .& .
-Canada model s: T he daytime running lig hts
will come on automa tically when the igni ­
t ion is on and the light switch<=> fig .
40 is in
the
O posit ion, the :oo~ position or the AUTO
posit ion (on ly in daylight conditions)<=>.& .
AUTO -Automatic headlights swi tch on and
off depend ing o n brightness , fo r example in
twi light, during rain or in tunnels<=>.& .
:oo~ -Side marker lights
io -Low beam head lights
~ -All-weather lights
@!l -Rear fog lights *. When th e rear fog lights
a re on , the symbol
0$ on the sw itch will i llu­
minate .
All-weather light s
In vehicles with all -weather lights, the front
lights are ad justed automatically so that you
are less like ly to see glare from your own
headlig hts, for example when driving on a wet
road .
Automatic dynamic headlight range
control *
Your vehicle is equipped with a headlight
range control sys tem so that the headligh ts
do not blind oncoming traffic if the vehicle
load cha nges . The headlight range a lso ad­
justs automatically when braking and acceler­ at ing .
Light function s
The following ligh t funct ions are available de·
pending on veh icle equipment and o nly fu nc­
t io n when the lig ht switch is i n the AUTO pos i­
t ion . You can deactivate these functions in the
MM I under
Audi adaptive light r:!> page 47 .
Static cornering light *· the cornering light
switches on automatically when the steering
wheel is turned at a certa in angle at speeds
u p to approxima tely 44 mph ( 70 km/h) and
when the t urn sign al is activated at speeds up
to approximately 25 mph (40 km/h) . The area
to the s ide of the vehicle is illuminated better
whe n turning.
Dynamic curv e light * -the curve ligh t only
f unct ions at speeds between approximately 6
mph (10 km/h) and 68 mph ( 110 km/h) and
adapts itse lf to the cu rves in the road.
Highway light function* -this function
adapts the lighting for highway driving based
o n ve hicle speed .
Ill>

_& WARNING
-Automatic headlights are only intended
to assist the driver . They do not relieve
the driver of his responsibility to check
the headlights and to turn them on man­
ually according to the current light and
visibility conditions. For example, fog
cannot be detected by the light sensors.
So always switch on the headlights
io
under these weather conditions and
when driving in the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists. Always turn on
the headlights so that you can see ahead
and so that others can see your car from
the back.
- Please observe legal regulations when
using the lighting systems described.
(D Note
The rear fog lights should only be turned
on in accordance with traffic regulation, as
the lights are bright for following traffic.
(D Tips
- The light sensor* for automatic dynamic
headlight range control* is located in the
rear view mirror mount. You should
therefore not apply any stickers to the
windshield in this area in order to pre­
vent malfunctions or failures.
- In the event of a light sensor malfunc­
tion, the driver is notified in the instru­
ment cluster display ~
page 22.
- You will hear a warning tone if you open
the driver door when the exterior lights
are switched on.
- In cool or damp weather, the inside of
the headlights, turn signals and tail
lights can fog over due to the tempera­
ture difference between the inside and
outside. They will clear shortly after
switching them on. This does not affect
the service life of the lighting. Clear vision 4
7
Emergency flasher
The emergency flasher makes other motorists
aware that you or your vehicle are in an emer­
gency situation .
Fig. 41 Center consol e: eme rge ncy flash er sw itc h
.,. Press the switch&..~ fig. 41 to turn the
emergency flashers on or off.
When the emergency flasher is on, all four
turn signals blink at the same time. The turn
signal indicator lights
B DI in the instru­
ment cluster, as well as the light in the emer­
gency flasher switch &.. blink likewise. The
emergency flasher also works when the igni­
tion is turned off.
The emergency flashers will turn on automati­
cally if you are in an accident where the airbag
has deployed.
@ Tips
You should turn on the emergency flashers
when:
- you a re the last vehicle standing in a traf­
fic jam so that any other vehicles coming
can see you, or when
- your vehicle has broken down or you are
in an emergency situation, or when
- your vehicle is being towed by a tow
truck or if you are towing another vehicle
behind you.
Adjusting the exterior lighting
The settings ore adjusted in the MMI.
.,. Select: !CAR ! function button> Car systems
control button > Vehicle settings > Exterior
lighting. ..,.

48 Clear vision
Automatic headlights
You can adjust the following settings in the
Automatic headlights menu:
Headlights a ctivation time -You can adjust if
the head lights switch on
Early , Med. or Late
according to the sensitivity of the light sensor.
Audi adaptive light* -You can switch adaptive
light
On and Off.
Automatic high beams*
You can switch the high beam assist on and
off .
Daytime running lights
USA models :
You can switch the daytime run ­
ning lights
on and off .
Canada models:
The function cannot be
turned off. It is activated automatica lly each
time the ignition is switched on . This menu
item is shown "greyed out".
Coming home, Leaving home
The coming home function illuminates the
area outside the vehicle when you switch the
ignition off and open the driver's door. To turn
the function on, select
Lights when leaving
car> On.
The leaving home function illuminates the
area outside the vehicle when you un lock the
ve hicle . To turn the funct ion on, select
Lights
when unlocking car > On .
The coming home and leaving home functions
on ly operate when it is dark and the light
switch is in the
AUTO position.
Turn signal and high beam lever
The lever on the left side of the steering col­
umn is used to operate the turn signals and
the high beam as well as the headlight flash­
er.
Fig. 42 Tu rn signal and high beam lever
The turn signa l and high beam lever has the
following functions:
Turn signals ¢ 9 (D@
.. Push the lever up as far as it can go to turn
on the right turn signal or down to turn on
t he left turn signal
¢ fig. 42 .
N 0 ... 'i' :r
~
.. Move the lever briefly until you meet res ist·
ance and re lease it to flash three times.
.. Move the lever (up or down) until you meet
resistance and hold it there to determine
the flashing time for the turn signals.
High beam [D @
.. Push the lever forward to switch on the high
beam (vehicles with high beam assist*
¢page49).
.. Pull the lever back towards you to switch off
the high beam .
Headlight flasher [D ©
.. Pull the lever toward the steering wheel to
use the headlight flasher.
Notes on these features
-The turn signals only work w ith the ignition
switched on. The indicator lights
ID or iPJ
in the instrument cluster ¢page 11 also
blink.
- After you have t urned a corner, the turn sig -
na l switches off automatically .
Ill>

,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-The high beam works only when the head­
lights are on. The indicator light
II in the
instrument cluster ill uminates when the
high beams are on.
- The
headlight flasher works only as long as
you hold the lever -even if there are no
lights turned on. The indicator light
II in
the instrument cluster illum inates when you
use the head light flasher .
A WARNING
Do not use the high beam o r headlight
flasher if you know t hat these could blind
on coming traffic.
High beam assist
A ppl ies to vehicles : wit h high bea m ass ist
-
The high beam assist automatically switches
the high beams on or off, depending on the
surroundings and traffic conditions.
F ig. 4 3 Tu rn signa l an d h igh beam lever: Turning on
and off t he h igh beam ass ist
Activating high beam a ssist
Requirement : The light sw itch must be in the
AUTO position, the low beam headlights must
be on and the high beam assist must be
sw itched on in the Infotainment~
page 47.
.. Press the lever forwards (Din order to acti-
vate the high beam ass ist. The indicator
light
IIJ turns on in the inst rument cluste r
display and the high beams switch on or off
automati ca lly. The indica to r ligh t
Iii turns
on if the high be ams were switched on.
Switching the high beams on /off
manually
R equi rement : Hig h beam ass ist is activated.
Clear v is ion 49
If the high beams d id not swi tch on/off auto ­
matically when expected, you may instead
switch them on/off manually:
.. To swi tch the high beams on manually, press
the lever forwa rds (D. The indicato r light
Bl
turns on.
.. To switch the high beams off manually, pull
the lever backwards @. The high beam as­
sist is deactivated .
Operating the headlight fla sher
.. To operate the flashe rs while the high beam
assist is active and the high beams are
sw itched off, pull the lever into posit ion @.
The high beam assist will remain active.
Messag es in the instrument cluster
di splay
Headlight ass ist: System fault
Drive to your authorized A udi dealer immedi­
ate ly to have the ma lfunction corrected. Yo u
can still switch the high beams on or off man­
u ally.
Headlight assi st: Unavailable . No camera
view
T he came ra v iew is b locked, for example by a
sticker o r debr is.
The sensor is loca ted between the inter io r
r earvi ew mirror and the w indshield . There­
fo re, do not p lace a ny s tick ers i n this a rea on
t h e windsh ie ld.
Service setting
There is a different sensit iv ity sett ing for serv­
ic ing . T hi s sett ing can be activated by pressing
and holding the b utton on the int erio r r ear­
view m irror for more tha n 18 seconds. The
L E D next to the button blinks th ree times.
If
yo u have accidentally se lec ted this service
function, the origi nal sensitivity will be auto­
matically restored the next t ime yo u sw itch
the ignit ion on.
IJ>,

50 Clear vis ion
& WARNING
H igh beam assist is only intended to assist
the driver. The driver is still responsible for controlling the headlights and sw itching
th e high beams on and off manually de­
pending on traffic, l ighting and visibility
condi tions. Failure to intervene manually
may lead to ris k of accident . It may be nec­
essary to operate the high beams man ua l­
ly in the following situat ions, e.g .:
- For adverse weather conditions such as
fog, heavy rain, blowing snow or spraying
water .
- On roads where oncoming traffic may be
partia lly obsc ured such as expressways .
-If there are individuals on the road with
no light ing or poor lighting, such as cy ­
cl ists .
- In tight c urves and on steep s lopes .
- In poorly lit areas.
- With strong reflectors su ch as signs.
- If the area of the windshie ld nea r th e
sensor is fogged over, dirty, icy or cov­
ered w ith a st icker.
(D Tips
- The high beam ass ist is active above a
speed of approx . 25 mph (40 km/h).
- If afte r activation, your speed falls below
approx . 15 mp h (24 km/h), the high
beams w ill automatically be switched
off.
Interior lights
Front and rear interior lighting
Fi g. 44 Headliner: Front interior lights
F ig. 45 Rear headli ner : Read ing light
Press the app ropriate button ~ fig . 44:
~ -Inter ior light ing on/off
l!l -Door contact switch. The interior lighting
turns on automatically when you u nlock the
vehicle, open a door or switch the ignition off.
The interior light ing turns off several seconds
after you close the doors, when you lock the
vehicle or when you switch the ignition on.
When a doo r is open, the light turns off after
a few min utes.
~ -Read ing lights on/off
~ - Switching the rear reading lights on/off
from the cockpit .
I REAR MODEi* -Switching the rear readi ng
li ghts on/off from the cockpit : press the
I REAR MODE ! button and then th e appropriate
button ~ in the cockpit.
Ambience lighting
Applies to veh icles: w it h amb ience l ig h ting
You can select a color profile and brightness
for the ambie nce lighting in various areas of
the ve hicle, called zones.
Turning ambience lighting on
.. Select in the MMI: ICAR ! function button >
Car systems control button > Vehicle set·
tings > Interior light ing > On .
Adjusting /turning off the brightness
• Sele ct in the MM I: ICARI fu nction button >
Car sy stems control b utton > V ehicle set­
ting s> Inte rior light ing > Brightness .

.. Turn the knob to the desired vehicle area
and press the knob . The bar that appears in­
dicates the selected brightness .
.. To increase or reduce the brightness, turn
the knob and press it.
S electing a color profile*
.. Se lect in the MMI:
!CAR ! function b utton >
Ca r sys tems control button > Vehi cle se t­
tings
> In terior light ing > Colo r profile .
The amb ience lig hti ng turns on when the
function is activated in the MMI and when you
turn the headlights on whi le the ignition is
switched on.
Adjusting the b rightness
You can ad just the brightness for the four
zones Front top , Fr ont f ootwell , Rear top and
Rear footwell or for All area s at the same
time.
Selecting a color pr ofile
You ca n select from the Ivory, Polar and Ru­
b y/ Polar color profiles .
(I) Tips
The settings are automati cally sto red and
a ssigne d to the remote con tro l key that is
in use.
Instrument illumination
You can adjust the brightness of the instru­
ment and display illumina tion as well as the
Head-up Display*.
F ig. 46 Instrument illum ination
.,. Press the knob to release it.
Clear vi sion 51
.. Turn the knob toward" -" or "+" to reduce or
i ncrease the brightness .
.. Press the knob aga in to return it to its origi­
nal position.
(D Tips
The instrument illumination (for dials and needles) lights on when the ignition is
switched on and the vehicle lights are
turned off. As the daylight fades, t he illu­
mination of the dials li kewise d ims a uto­
matically and w ill go out completely when
the outs ide light is very low. Th is feature is
meant to rem ind you to sw itch on the
headligh ts when ou tside ligh t conditions
b ecome poor .
Vision
Sun visors
Fig. 4 7 Sun visor
E )
-' @
The sun visors for the driver and passenger
can be re leased from their brackets and
turned toward the doors
c> fig. 47@. They
can a lso be moved back and forth lengthwise
in th is position .
The mirror light switches on when the cover
over the vanity m irror @opens.
There is a shade between the dr iver's and pas­
senger's s un v isors that can be used to cover
the gap above the rearview mirror.

52 Clear vision
Sun shade
Fig. 48 Cockp it : Sun shade switc h
Fig. 49 Rear door: S un shade button
Extending/retracting the rear window
shade*
~ To extend or retract the sun shade from the
cockpit,
press the r.t.l button in the center
console
c> fig . 48 .
~ To extend or retract the sun shade from the
rear of the vehicle ,
press the rn button in
the door
c> fig. 49.
Extending the rear door sun shades*
~ Close the window in the rear door.
~ To extend th e sun shade from the driver's
seat,
pull the left/r ight rear power window
switch~ in the driver's door .
~ To extend the sun shade from the rear of
the vehicle,
pull the power window sw itch
11:. in the left/right rear door.
Retracting the rear door sun shades*
~ To retract the sun shade from the driver's
seat ,
press the left/ right rear power window
switch~ in the driver's door .
~ To retract the sun shade from the rear of the
vehicle,
press the power window switch~
i n the left/ right rear door. You
can adjust the settings for the rear sun
shade so the shade retracts automatically
when you select the reverse gear. Select:
CAR
function button > Car systems control button
> Vehicle settings > Automatic rear blind >
On. The settings are automatically stored and
ass igned to the remote control key. The sun
shade extends again as soon as the vehicle be­
gins traveling forward at a speed greater than
9 mph (15 km/h), as long as the ignition has
not been sw itched off in the meantime .
_&. WARNING ~
When lowering or raising the sunshade,
make sure there is nothing in its way and
that it has a free path to travel. This could
cause personal injury.
(D Tips
-
- Pressing the button~ several times
consecutively can trigger the overload
protection. The sun shade can only be ex­
tended/retracted again after a brief wait­
ing period.
- The rear window sun shade only func­
tions when the vehicle interio r is warmer
than
14°F (-10°() .
· Vanity mirror in the rear
Applies to vehicles: with vanity mirrors in the rear
Fig. 50 Rear headliner : vani ty mirro r
~ Press the button to fold the mirror open .
The mirror lighting turns on automatically.
~ To change the mirror's ang le, move it for­
ward/back w ith your hand.

Wiper and washer system
Switching the windshield wipers on
Fig. Sl W indshield wiper leve r
Move the windshield wiper lever to the corre­
spond ing pos ition:
@ -Windshie ld w ipers
off
(D -Rain sensor mode. The w indshie ld w ipers
switch on once the vehicle speed exceeds ap­
proximately 2 mph (4 km/h) and it is raining.
The higher the rain sensor sensitivity is set
(switch @to the right), the earlier the w ind­
shield wipers react to moisture on the wind­
shie ld. You can deact ivate rain sensor mode in
the MMI, which w ill then activate intermittent
mode. Select:
ICARI function button > Car sys­
t e m s
control button > Dri ver ass is t > Ra in
s en sor
> Off . In intermittent mode, you can
adjust the interval time using the switch @.
@ -Slow wiping
@-Fast wiping
©-Single wipe. If you hold the lever in this
position longer, the wipers switch from slow
wiping to fast wip ing .
® -Clean the windshield . The wipers wipe
one time after several seconds of driving to
remove water drop lets. You can switch this
function
off by moving the lever to position ®
within 10 seconds after the afterw ipe . The af­
terw ipe f unction is react ivated the next time
you switch the ig nition on.
Cleaning the headlights . The headlight wash­
er system* only functions when the headlights
are on. If you move the lever to position ®,
Clear vi sion 5 3
the headlights and the night vision system
camera* are washed in intervals.
A WARNING
-The rain sensor is only designed to assist
and support the driver.
It remains entire­
ly the driver's responsibility to monitor
outs ide weather cond itions and to man­
ually activate the wipers as soon as rain
or drizzle reduces visibility through the
windshie ld.
- The windsh ield must not be treated w ith
wate r-repellent mate rials. They can in­
crease glare unde r poo r vis ibility condi­
tions such a s wetness, d arkness, or w hen
the sun is low on the hori zon. In addi ­
tion, they can cause the w indshield wip­
ers to chatter.
- Properly f unctioning windshield wiper
blades are req uired for a clear v iew and
safe driving
¢ page 54, Replacing
windshield wiper blades.
(D Note
- In the case of frost, check whether the
windshield wiper blades are frozen to
the windshield. Switching on the wind­
shield wipers can damage the wiper
blades!
- Prior to us ing a car wash, the w indshield
w iper system must be sw itched off ( lever
in posit ion @). T his he lps to prevent un­
intentional switching on and damage to
the windsh ield wiper system.
- Do not use the wipers to clear a frosted
w indow. Us ing the wipers as a conve n­
ient ice scrape r will destroy the wiper
blades.
(D Tips
- The windshield wipers are sw itched off
when the ign it ion is off . Activate the
w indshield wipe rs after the ignition is
switched back o n by movi ng the w ind­
shield wiper lever to any positi on.
- Worn or d irty wi ndshield wipe r blades
result in streaking. This ca n affec t the

54 Clear vis ion
rain se nsor f unction . Check yo ur
winds hield wiper b lades regularly.
- The washer fluid nozzles of the wind­
sh ield washer system are heated at low
temperatures when the ignition is on .
- When stopping temporarily, e .g . at a
traffic light, the set speed of the wind­
s h ield wipers is automatically red uced by
one speed.
Cleaning w indshield wiper blades
Clean the w indshield wiper blades when they
begin to leave streaks . Use a soft cloth and
g lass cleaner to clean the windsh ield wiper
b lades.
.. Place the windshield wiper arms in the serv­
ice position . Refer to ¢
page 54.
.. Lift the w iper arm away from the front win­
dow.
_& WARNING
Dirty w indshie ld w iper blades can impa ir
your view. Thi5 can lead to acc ident5 .
Replacing windshield wiper blades
Fig. 52 Removi ng w inds hield w ipe r blades
Wiper ser vice position / Blade
replacem ent position
-
.. Switch the ign ition off and move the w ind­
shield wipe r leve r to posi tion @ ¢
page 53,
fig. 51. The windshield wipe rs move into the
service position.
.. To bring the wipe rs back into the original
position, switch the ignition on and press
the windshie ld wiper lever. You can also t
urn the se rv ice position on or off
in the MMI:
.. Switch the windshie ld wipers
off (position
@ ¢page 53, fig. 51) .
.. Select: !CARI function button> Car systems
contro l butto n > Serv icing & checks > Wip er
serv ice position
> On.
R emo ving the wipe r blade
.. Lift the windshield wiper arm up from the
w indshield.
.. Press the locking knob
(D ¢ fig. 52 on the
w iper blade. Hold the wiper blade firmly .
.. Remove the wipe r blade in the d irection of
the arrow .
Attaching the wipe r blade
.. Insta ll the new wiper blade in the reta iner
on the wiper arm @unt il you hear it click in­
to place on the w iper arm .
.. Place the w iper arm back on the windshield .
.. Tu rn the se rvice position
off.
_& WARNING
-
F or your s afety, you shou ld rep lace the
wiper b lades once or twice a yea r. See your
a uthorized Audi dea ler fo r replacement
b lades .
(D Note
- The windsh ie ld wiper b lades m ust only
be folded away when in the service posi­
tion! Otherwise, yo u ris k damaging the
paint on the hood or the windshie ld w ip­
er motor.
- Yo u should not move your vehicle or
press the windshie ld wiper lever when
the wiper arms are folded away from the
windshield. The windsh ield wipers wou ld
move back into their or iginal position
and co uld damage the hood and wind­
shield.
- To help prevent damage to the w iper sys­
tem, always loosen blades w hich are fro­
zen to the windshield before operating
w ipers. .,.